ページ1に含まれる内容の要旨
OPERATOR’S MANUAL
30cc String Trimmers and Brushcutters
SS30
RY30240
CS30
RY30220
BC30
RY30260
Your new trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFEREN
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Introduction ..................................................................................................................................................................... 2 � General Safety Rules ....................................................................................................................................................... 3 � Specific Safety Rules ................................................................................................
ページ3に含まれる内容の要旨
GENERAL SAFETY RULES � Do not touch area around the muffler or cylinder of the WARNING: unit, these parts get hot from operation. Always stop the engine and remove the spark plug wire Read and understand all instructions. Failure to follow all before making any adjustments or repairs except for instructions listed below may result in electric shock, fire carburetor adjustments. Wear your protective equipment and/or serious personal injury. and observe all safety instructions. When the
ページ4に含まれる内容の要旨
SPECIFIC SAFETY RULES Replace any blade that has been damaged. Always make SPECIFIC SAFETY RULES FOR TRIMMER sure blade is installed correctly and securely fastened USE before each use. Failure to do so can cause serious Replace string head if cracked, chipped, or damaged injury. in any way. Be sure the string head or blade is properly ® Use only the manufacturer’s replacement Tri-Arc blade installed and securely fastened. Failure to do so can cause intended for use on this brushcu
ページ5に含まれる内容の要旨
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning for safe operation of this product. SYMBOL NAME EXPLANATION Safety Alert Symbol Precautions that involve your safety. To reduce the risk of injury, user must read and under- Read the Operator’s Manual stand operator’s manual before using this product. Wear eye protection which is marked to comply Wear Eye and Hearing Protection with ANSI Z87.1 as well as hearing protection when operati
ページ6に含まれる内容の要旨
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ページ7に含まれる内容の要旨
FEATURES PRODUCT SPECIFICATIONS Weight - (without fuel) CS30 ....................................................................................................................................................10.7 lbs. (4.9 kg.) SS30 ....................................................................................................................................................12.1 lbs. (5.4 kg.) BC30 ..........................................................................................
ページ8に含まれる内容の要旨
FEATURES SS30 STARTER GRIP AND ROPE REAR HANDLE TRIGGER LOCK PRIMER BULB COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSING FRONT HANDLE STRING HEAD KNOB STRAIGHT SHAFT GRASS DEFLECTOR Fig. 1b BC30 STARTER GRIP AND ROPE REAR HANDLE TRIGGER LOCK “J” HANDLE PRIMER BULB COUPLER THROTTLE TRIGGER DRIVE SHAFT HOUSING KNOB BLADE SHOULDER HARNESS BRUSHCUTTER GUARD Fig. 1c 8
ページ9に含まれる内容の要旨
FEATURES KNOW YOUR STRING TRIMMER GRASS DEFLECTOR See Figures 1a - 1c. The trimmer includes a grass deflector that helps protect The safe use of this product requires an understanding of you from flying debris. the information on the tool and in this operator’s manual as TOP-MOUNTED MOTOR well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating The top-mounted motor improves balance and is located features and safety rules. a
ページ10に含まれる内容の要旨
ASSEMBLY INSTALLING THE POWER HEAD TO THE STRING TRIMMER ATTACHMENT SHAFT See Figure 2. COUPLER GUIDE WARNING: RECESS Never install, remove, or adjust any attachment while power head is running. Failure to stop the engine can BUTTON cause serious personal injury. The attachment connects to the power head by means of a coupler device. Loosen the knob on the coupler of the power head shaft and remove the end cap from the attachment. POSITIONING Push in the button located on the attach
ページ11に含まれる内容の要旨
ASSEMBLY ATTACHING THE FRONT HANDLE - CS30 AND SS30 FRONT HANDLE See Figure 4. Remove 2 wing nuts, 2 bolts, and clamp from the front handle. Install the front handle onto the top side of the drive shaft housing and move it to a comfortable position. Place the bolt through the front handle. NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle. Reinstall the clamp, bolts, and wing nuts. BOLT Tighten wing nut securely. WING ATTACHING THE “J” HANDL
ページ12に含まれる内容の要旨
ASSEMBLY ATTACHING THE GRASS DEFLECTOR HEX GRASS SCREW DEFLECTOR WARNING: The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury. BRACKET TO ATTACH THE CURVED SHAFT GRASS LOCK DEFLECTOR - CS30 WASHER See Figure 6. Remove hex screw, flat washer, lock washer, and wing nut from grass deflector. Press the grass deflector onto the bottom of the curved FLAT shaft as shown. WASHER WING NUT Fig. 6
ページ13に含まれる内容の要旨
ASSEMBLY ATTACHING THE SHOULDER HARNESS - LATCH BC30 See Figure 9. Connect the latch on the shoulder harness to the strap hanger. Adjust the strap to a comfortable position. STRAP HANGER CONVERTING FROM BRUSHCUTTER TO STRING TRIMMER - BC30 To convert from the brushcutter to the string trimmer, remove SHOULDER the blade and brushcutter guard, attach the straight shaft HARNESS Fig. 9 grass deflector and install the string head. ® REMOVING THE TRI-ARC BLADE AND BRUSHCUTTER GUARD See Fig
ページ14に含まれる内容の要旨
ASSEMBLY REMOVING THE STRAIGHT SHAFT GRASS GEAR HEAD DEFLECTOR AND STRING HEAD FLANGED WASHER See Figures 10 - 13. Align the slot in the flanged washer with the slot in the STRING HEAD gear head. ASSEMBLY Place the gear head locking tool through the slot in the flanged washer and gear head. SLOT Remove the string head assembly. Remove the flanged washer and retain it for the blade installation. Remove the screw securing the grass deflector. Remove the grass deflector. NOTE: St
ページ15に含まれる内容の要旨
OPERATION FUELING AND REFUELING THE TRIMMER WARNING: FUEL MIXTURE To avoid burns from hot surfaces, never operate unit with This product is powered by a 2-cycle engine and requires the bottom of the engine above waist level. pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gaso- line and 2-cycle engine oil in a clean 1 gallon container ap- Hold the trimmer with your right hand on the rear handle and proved for gasoline. your left hand on the front handle. Keep a firm grip with both Reco
ページ16に含まれる内容の要旨
OPERATION CURVED SHAFT TRIMMER WARNING: Always hold the string trimmer away from the body keep- DANGEROUS ing clearance between the body and the product. Any CUTTING AREA DIRECTION OF contact with the housing or string trimmer cutting head can ROTATION result in burns and/or other serious personal injury. TO ADVANCE THE CUTTING LINE String advance is controlled by tapping the string head on grass while running engine at full throttle. Run engine at full throttle. Tap the spool retainer
ページ17に含まれる内容の要旨
OPERATION Inspect and clear the area of any hidden objects such as OPERATING THE BRUSHCUTTER glass, rocks, concrete, fencing, wire, wood, metal, etc. See Figures 19 - 20. Hold the brushcutter with your right hand on the rear handle Never use blades near sidewalks, fencing, posts, build- and the your hand on the “J” Barrier Handle. Keep a firm ings or other immovable objects. grip with both hands while in operation. Brushcutter should Never use a blade after hitting a hard object without
ページ18に含まれる内容の要旨
OPERATION STARTING AND STOPPING See Figures 21 - 23. PRIMER BULB TO START A COLD ENGINE: DO NOT squeeze the throttle trigger until the engine starts and runs. Lay the trimmer on a flat, bare surface. PRIME - Press the primer bulb 7 times. SET the start lever to the START position. PULL the rope until the engine starts. IGNITION Wait 6-10 seconds, then squeeze the trigger to run. SWITCH NOTE: Squeezing the throttle trigger releases the start lever to the RUN position. TO START A
ページ19に含まれる内容の要旨
MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. SPOOL WARNING: RETAINER Always wear safety goggles or safety glasses with side Fig. 24 shields during tool operation. If operation is dusty, also SPRING wear a dust mask. WARNING: SLOTS Before inspecting, cleaning, or servicing the machine, shut off engine, wait for all moving parts to stop, and disconnect spark plug wire and move it away from spark
ページ20に含まれる内容の要旨
MAINTENANCE To install the spool retainer: Turn the spool retainer clockwise for model CS30. Turn SPRING SPOOL the spool retainer counterclockwise for models SS30 and BC30. ARROWS ON Pull the strings again to rotate the spool into cutting SPOOL position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head. ANCHOR STRING REPLACEMENT HOLE See Figures 26 - 28. Use only monofilament string. Use original
