ページ1に含まれる内容の要旨
5850-93110 (9809)
OWNER/OPERATOR MANUAL
TRIMMERS / STICK EDGERS
BT2200LDC
BC2200E
BC2200LDC
HE2200LDC
BT2200LDC BC2200E BC2200LDC HE2200LDC
IMPORTANT :
WARNING
Before operating your RedMax product,
read this manual carefully and completely.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Thank you for choosing a RedMax trimmer / stick edger. This manual will provide you with full understanding of the necessary instructions for assembly, operation and maintenance of the equipment. Please read this manual carefully before starting operation. For continued safe and reliable operation, use ONLY original RedMax parts and accessories, Adhere to all notes and warnings. CONTENTS FOR SAFE OPERATION · · · · · · · · · · · · · · · · · · · · · · 2 SETUP · · · · · · · · · · · · · · · · ·
ページ4に含まれる内容の要旨
FOR SAFE OPERATION ■ KNOW YOUR UNIT ■ OPERATE YOUR UNIT SAFELY 1.Read this Owner's Manual carefully until 1.Inspect the entire unit before each use for you completely understand and can follow worn, loose, or damaged parts. Do not use all safety rules, precautions, and operating until the unit is in proper working order. instructions before operating the unit. 2.Keep the handles free of oil and fuel. 2.Restrict your unit to users who understand 3.Never start or run the engine inside a and fol
ページ5に含まれる内容の要旨
SETUP ■ HE2200LDC 1.Install the driveshaft assembly to the engine 1.Install the blade guard to the gear case with unit. Clamp it securely with the attached the provided 3 screws. bolt and nut. HE2200LDC 2.Place the blade between the cutter holders 2.Connect the throttle cable to the engine. (A) and (B) while locking the gear shaft by putting the bar , one of the tools provided, through the key holes on the holder(A) and the gearcase. Use the socket and the bar as shown in the picture below to ti
ページ6に含まれる内容の要旨
FUEL The RedMax engines are lubricated by oil ■ FUELING UNIT specially formulated for air-cooled 2-cycle 1.Untwist and remove the fuel cap. Rest the gasoline engine use. When RedMax oil is not cap on a dustless place. available, use an anti-oxidant added quality oil 2.Put fuel into the fuel tank to 8O% of the full formulated for air-cooled 2-cycle engine use. capacity. RECOMMENDED MIXING RATIO 3.Fasten the fuel cap securely and wipe up GASOLINE 32 : OIL 1 any fuel spillage around the unit.
ページ7に含まれる内容の要旨
OPERATION ■ STARTING ENGINE NOTE : Avoid pulling the rope to its dead end or WARING!!! returning it by releasing the knob. Such Keep the cutting head off the ground and actions can cause starter failures. clear of surrounding objects as it will start 4.When the engine has started, move the rotating upon starting of the engine. choke lever gradually upward to open 1.Press the primer bulb until fuel flows out in choke. the clear tube (5 to 7 times). Lace the 5.Allow the engine to warm up for a
ページ8に含まれる内容の要旨
OPERATION ■ LINE HEAD USAGE • ADJUSTING LINE LENGTH Your trimmer is equipped with a bump head • HOW TO USE that allows the operator to advance the line WARING!!! without stopping the engine. When the line becomes short, lightly tap the head on the 1.Always wear eye protection such as ground while running the engine at full safety goggles. Never lean over the throttle. Each time the head is bumped, the rotating cutting head. Rocks or other line advances about 1 inch (25.4 mm). For debris could
ページ9に含まれる内容の要旨
OPERATION ■ METAL BLADE USAGE WARING!!! NOTE : The operator must keep his own path of Do not use the Metal Cutting Blade for advance clear due to the possibility of model BT2200LDC and BC2200E swinging around and seriously injuring a bystander or helper. • Always cut by guiding the head from your right to left. CONTROLLING BLADE BOUNCE • When mowing a wide area, start working Blade bounce can cause serious personal from the left side to avoid interference of cut injury. Carefully study this sect
ページ10に含まれる内容の要旨
OPERATION g.Cut only from your right to your left. TO SHARPEN BLADE : h.Keep your path of advance clear of 1.Grind away each cutting edge and its back material that has been cut and other evenly and maintain similar shape to debris. original. 3. How you can maintain the best control: 2.Sharpen each cutting edge and make sure the bottom corner is rounded. a.Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and .10"R left hands completely a
ページ11に含まれる内容の要旨
MAINTENANCE I. Bump head for BT2200LDC and BC2200E ■ REPLACING TRIMMING LINE To refill a new trimming line either ; A : Install the prewound reel #153577 or B : Rewind the existing reel. For replacement line, use a diameter of .080 in (2.03 mm). The engine may overheat and fail if you use a larger line. For safety reason, • WINDING NEW LINE do not use metal-reinforced line. 1.Take 25 ft (7.6 m) of new trimming line, insert one end through either hole on the A : REWINDING THE EXISTING SPOOL inne
ページ12に含まれる内容の要旨
MAINTENANCE • INSTALLING THE REEL 2.Hold the inner reel in place and screw in the 1.Insert each end of the line through the Bump Knob bolt in the correct direction eyelet on the outer spool. Then pull the end (clockwise for BT2200LDC and firmly to release the line from the holding BC2200E). slot. B : INSTALLING A PREWOUND REEL 1.Follow the instructions in DISASSEM- BLING THE HEAD. 2.Follow the instructions in INSTALLING THE REEL. II. Bump head for BC2200LDC 1 4 6 2 5 7 3.8m (12.5') 7.6m (25')
ページ13に含まれる内容の要旨
MAINTENANCE 8 11 14 THIS SIDE UP WIND LINE 1 9 2 THIS 10 12 15 SIDE UP 13 11
ページ14に含まれる内容の要旨
MAINTENANCE ■ AIR FILTER ■ SPARK PLUG The air filter, if clogged, will reduce the engine Starting failure and mis-firing are often caused performance. Every 30 days, check and clean by a fouled spark plug. Periodically clean the the filter element in warm, soapy water as spark plug and check that the spark gap is required. Dry completely before installing. If within the correct range. the element is broken or shrunk, replace with For a replacement plug, use Champion a new one. RCJ6Y or the equ
ページ15に含まれる内容の要旨
SPECFICATIONS ■ BT2200LDC Overall size (LxWxH) ···························································································62.2x9.7x17.9 (in) Dry weight ·························································································································10.1 (lbs) Engine Type ························································································Air-cooled 2-stroke gasoline Model ·································································
ページ16に含まれる内容の要旨
PARTS LIST Fig.1 TRIMMER UNIT FOR BT2200LDC Fig.1 TRIMMER UNIT FOR BT2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty ————— 1 Curved shaft ass'y 1 17 Guard mount screw 153318 1 ————— 2Flex.drive shaft 1 18 Guard ass'y 683445 1 3 Throttle housing ass'y 181125 1 19 Blade ass'y 682061 1 4 Throttle lever 180975 1 20 Anti-rotation screw 145569 1 5Screw 145569 1 21 Spool shaft 153313 1 6Screw 147544 5 22 Outer spool ass'y 153619 1 7 Spring 610314 1 23 Eyelet 145566 2 8 Handl
ページ17に含まれる内容の要旨
Fig.2 TRIMMER UNIT FOR BC2200E Fig.2 TRIMMER UNIT FOR BC2200E Key# Description Part Number Q'ty Key# Description Part Number Q'ty ————— 1 Straight shaft ass'y 1 16 Clamp assembly 153597 1 ————— 2Flex drive shaft 1 17 Screw, Anti-rotation 145569 1 3 Throttle housing ass'y 181125 1 18 Spool, Outer w/eyelet 153619 1 (include item 20) 4 Throttle lever 180975 1 19 Eyelet 145566 1 5 Spring 610314 1 20 Retainer 610660 1 6Screw 145569 1 21 Spring 610317 1 7Screw 147544 5 22 Reel, inner 153600 1 8 Handle
ページ18に含まれる内容の要旨
Fig.3 TRIMMER UNIT FOR BC2200LDC Fig.3 TRIMMER UNIT FOR BC2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty ————— 1 Straight shaft ass'y 1 18 Housing UBTR-06 1 ————— 2Flex.drive shaft 1 19 Eyelet UBT-9 2 3 Gear box ass'y 147488 1 20 NUT UBTR-F10 1 ————— 1 4Screw 21 Spring UBT-4 1 5 Screw set 147677 1 22 Spool UBT-3 1 6Blade driver 147489 1 23 Button UBT-2 1 7 Lower retaining washer 147490 1 24 Cover UBT-1 1 8 Throttle housing ass'y 181125 1 25 Guard ass'y 6778-24000 1 9
ページ19に含まれる内容の要旨
Fig.4 STICK EDGER UNIT FOR HE2200LDC Fig.4 STICK EDGER UNIT FOR HE2200LDC Key# Description Part Number Q'ty Key# Description Part Number Q'ty ————— 1 Curved shaft ass'y 1 17 Retaining washer 613222 1 ————— 2Flex drive shaft 1 18 Retaining nut 613221 1 6779-24100 3 Throttle housing ass'y 181125 1 19 Guard Ass'y 1 4 Throttle lever 180975 1 20 Plate, rubber 6779-24120 1 5 Spring 610314 1 21 Plate 6779-24130 1 6Screw 145569 1 22 Bolt 00225-30512 2 7Screw 147544 5 23 Mounting Bolt assambly set 684070
ページ20に含まれる内容の要旨
Fig.5 ENGINE GROUP FOR BT2200LDC. BC2200E. BC2200LDC. HE2200LDC 18
