MTD MP426CSの取扱説明書

デバイスMTD MP426CSの取扱説明書

デバイス: MTD MP426CS
カテゴリ: トリマー
メーカー: MTD
サイズ: 6.21 MB
追加した日付: 1/29/2014
ページ数: 76
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスMTD MP426CSの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、MTD MP426CSに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書MTD MP426CSをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書MTD MP426CSのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - MTD MP426CSの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
MTD MP426CS 取扱説明書 - Online PDF
Advertisement
« Page 1 of 76 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書MTD MP426CSを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書MTD MP426CSの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

English
Operator’s Manual
Curved Shaft,
4-Cycle Trimmer
Model
MP426CS
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
PART NO. 769-02175 (01/06)

ページ2に含まれる内容の要旨

TABLE OF CONTENTS Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Know Your Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ページ3に含まれる内容の要旨

SPARK ARRESTOR NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention of fire. Check with

ページ4に含まれる内容の要旨

• Be aware of risk of injury to the head, hands and feet. • Be sure the cutting attachment is not in contact with anything before starting the unit. • Clear the area to be cut before each use. Remove rocks, broken glass, nails, wire, string and other • Use the unit only in daylight or good artificial light. objects which may be thrown or become entangled in • Avoid accidental starting. Remain in the starting the cutting attachment. Clear the area of children, position whenever pulling the starte

ページ5に含まれる内容の要旨

SECTION 1b: SAFETY & INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING SYMBOL MEANING • THROWN OBJECTS AND • SAFETY ALERT SYMBOL ROTATING CUTTER CAN Indicates danger, warning or caution. CAUSE SEVERE INJURY May be used in conjunction with other WARNING: Do not operate without symbols or

ページ6に含まれる内容の要旨

SECTION 2: KNOW YOUR UNIT Spark Arrestor Spark Plug Applications As a trimmer: Muffler • Cutting grass and light weeds • Decorative trimming around trees, fences, etc. Muffler Guard Starter Rope Grip Fuel Cap Shaft Grip On/Off Stop Control Throttle Control J-Handle Spark Plug Shaft Housing Air Filter Cover Primer Bulb Cutting Attachment Shield Line Cutting Blade Oil Fill Plug / Dipstick Cutting Attachment Engine Feet 6

ページ7に含まれる内容の要旨

SECTION 3: ASSEMBLY INSTRUCTIONS On some units, the J-handle may be pre-installed. Go to Installing the Cutting Attachment Shield step 5 if the J-handle is pre-installed. Use the following instructions if the cutting attachment shield on your unit is not installed. Install and Adjust the J-handle WARNING: To prevent serious personal 1. Place the J-handle between the top and middle injury, never operate the trimmer without clamp pieces. See Figure 1. the cutting attachment shield in place. (4) Sc

ページ8に含まれる内容の要旨

SECTION 4: OIL AND FUEL INFORMATION DANGER: OVERFILLING OIL CRANKCASE 2. Place the unit on a flat level surface. MAY CAUSE SERIOUS PERSONAL INJURY. 3. Remove the oil plug / dipstick from the crankcase. Check and maintain the proper oil level in See Figure 7. the crank case; it is important and cannot be overemphasized. Check the oil before each use and change it as needed. See Changing the Oil. RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase O-Ring is extremely impo

ページ9に含まれる内容の要旨

Unleaded Gasoline SECTION 4: OIL AND FUEL INFORMATION RECOMMENDED FUEL TYPE FUELING THE UNIT WARNING: Gasoline is extremely flammable Old fuel is the primary reason for improper unit and its vapors can explode if ignited. To avoid performance. Be sure to use fresh, clean, unleaded serious personal injury, always stop the engine gasoline. and allow it to cool before filling the fuel tank. NOTE: This is a four cycle engine. In order to avoid Do not smoke while filling the tank. Keep damage to the

ページ10に含まれる内容の要旨

SECTION 5: STARTING/STOPPING INSTRUCTIONS Stop/Off (O) WARNING: Operate this unit only in a well- Start/On ( I ) ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 9). To avoid serious injury, the operator and unit must be in a stable position while starting. Throttle To avoid serious personal injury, ensure any Control Add-On being used is inst

ページ11に含まれる内容の要旨

SECTION 6: OPERATING INSTRUCTIONS NOTE: Do not rest the bump knob on the ground while Holding the Trimmer the unit is running. WARNING: Always wear eye, hearing, foot CAUTION: Do not remove or alter the line and body protection to reduce the risk of cutting blade assembly. Excessive line injury when operating this unit. length may make the unit overheat. Before operating the unit, stand in the operating Some line breakage will occur from: position. See Figure 14. Check for the following: • Entan

ページ12に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS Maintenance Schedule NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by Perform these required maintenance procedures at the any non-road engine repair establishment, individual frequency stated in the table. These procedures should or authorized service dealer. also be a part of any seasonal tune-up. WARNING: To prevent serious injury, never NOTE: Some maintenance procedures may require perform

ページ13に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS 3. Pull old line out of the line loading and line locking 7. Repeat procedures 4-6 with the second piece of line. holes (Fig. 16 and 17). 8. Hold the outer spool. Wind the inner reel 4. Insert a piece of trimming line straight into one of the counterclockwise until approximately four (4) inches two eyelets in the outer spool. Push it up through the (102 mm) of line remain (Fig. 19). line loading hole in the inner reel (Fig. 16). Do not NOTE: Do not

ページ14に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS 2. Pull the old inner reel with existing line from the outer 3. Remove any existing line from the inner reel before spool. cleaning. Remove any debris or grass from the knob, spring, inner reel and foam seal. Wash the inner reel 3. Insert the ends of the prewound inner reel line into with warm soapy water (Fig. 24). the outer spool eyelets (Fig. 22). Push the new inner reel, arrow side up, into the outer spool. Inner Reel Fig. 24 4. Clean the shaft

ページ15に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS CHECKING THE OIL LEVEL CHANGING THE OIL The importance of checking and maintaining the proper For a new engine, change the oil after the first 10 hours of CAUTION: To prevent extensive engine operation. Change the oil while the engine is still warm. The wear and damage to the unit, always oil will flow freely and carry away more impurities. maintain the proper oil level in the crankcase. Never operate the unit with the CAUTION: Wear gloves to preven

ページ16に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS AIR FILTER MAINTENANCE Cleaning the Air Filter WARNING: To avoid serious personal injury, always turn your trimmer off and allow it to cool before you clean or service it. Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain the air filter will VOID the warranty. Figure 32 Figure 33 1. Open the air filter cover. Push the tab on the right side of the cover inward. Then pull the air filt

ページ17に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS Clean Air Filter ROCKER ARM CLEARANCE The condition of the air filter is important to the operation This requires disassembly of the engine. If you feel of the unit. A dirty air filter will restrict air flow and change unsure or unqualified to perform this, take the unit to an the air/fuel mixture. This is often mistaken for an out of authorized service center. adjustment carburetor. Check the condition of the air filter before adjusting the idle sp

ページ18に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS 3. Remove the screw behind the engine cover. See Adjusting Nuts Figure 38. Rocker Arms INTAKE Screw EXHAUST Feeler Gauge Figure 38 4. Disconnect the spark plug wire. Figure 40 5. Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise. Adjusting Nut 6. Remove the engine cover. See Figure 37. Rocker Arm 7. Clean dirt from around the rocker arm cover. Remove the screw holding the

ページ19に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS Replacing the Spark Plug SPARK ARRESTOR MAINTENANCE Use a Champion RDZ19H spark plug (or equivalent). The 1. Remove the muffler cover. See Rocker Arm Clearance. correct air gap is 0.025 inch (0.655 mm). Remove the 2. With a flat blade screwdriver or Torx T-20 bit, plug after every 25 hours of operation and check its remove the screw attaching the spark arrestor cover condition. to the muffler. See Figure 43. 1. Stop the engine and allow it to cool.

ページ20に含まれる内容の要旨

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS 3. Allow the engine to cool. Remove the spark plug and Cleaning put 1 oz. (30 ml) of any high quality motor oil or 2- WARNING: To avoid serious personal injury, cycle oil into the cylinder. Pull the starter rope slowly always turn your trimmer off and allow it to to distribute the oil. Reinstall the spark plug. cool before you clean or service it. NOTE: Remove the spark plug and drain all of the oil Use a small brush to clean off the outside of the


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 MTD 22K 取扱説明書 トリマー 18
2 MTD 243-540 取扱説明書 トリマー 9
3 MTD 244-600A 取扱説明書 トリマー 2
4 MTD 2079r 取扱説明書 トリマー 2
5 MTD 25P 取扱説明書 トリマー 3
6 MTD 18K 取扱説明書 トリマー 0
7 MTD 60-2310-6 取扱説明書 トリマー 1
8 MTD 316.745400 取扱説明書 トリマー 3
9 MTD 700 取扱説明書 トリマー 403
10 MTD 704r 取扱説明書 トリマー 0
11 MTD 60-2311-4 取扱説明書 トリマー 1
12 MTD 700rVP 取扱説明書 トリマー 2
13 MTD 60-2312-2 取扱説明書 トリマー 1
14 MTD 700r 取扱説明書 トリマー 21
15 MTD 705r 取扱説明書 トリマー 2
16 Sony PCS-G70P 取扱説明書 トリマー 12
17 Sony PCS-G70 取扱説明書 トリマー 12
18 ABC Office 440 取扱説明書 トリマー 2
19 Sony 370A 取扱説明書 トリマー 83
20 ABC Office 448 取扱説明書 トリマー 2