ページ1に含まれる内容の要旨
Hover Vac
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 01325 300303
www.flymo.com
eop.customer.services@electrolux.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
Carton Contents switchbox start/stop lever cable clip upper handle washers bolt handle knob bolt nut electric cable cable clip with moulded handle knob on plug lower handle fixing pin instruction manual fixing pin plastic cutters IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety If not used
ページ3に含まれる内容の要旨
4. Immediately disconnect from the mains electricity sup- 6. Exercise extreme caution when changing direction ply if the cable is cut, or the insulation is damaged. on slopes. Do not touch the electric cable until the electrical sup- 7. Using on banks and slopes can be dangerous. Do ply has been disconnected. Do not repair a cut or not use on banks or steep slopes. damaged cable. Replace it with a new one. 8. Do not walk backwards whilst operating your prod- 5. Your cable must be uncoiled,
ページ4に含まれる内容の要旨
Assembly Instructions Assembly of lower handle to hood (A) A 1. Place the ends of the lower handle into the slots 2. Secure lower handle to hood by firmly pushing fix- ing pin through holes in hood and handle (A1). 3. Repeat on the other side. • NOTE 1 Should a problem occur when securing handle with the fixing pin, carefully lever the pin out of location and repeat steps 1 to 3 above. B lock-off handle button knob Fitting Upper Handles to Lower Handles (B) 1. Ensure the upper handle is located
ページ5に含まれる内容の要旨
Adjusting the Cutting Height HIGHEST J This symbol visible • THERE ARE 2 CUTTING HEIGHTS (J & K) • Height of cut is adjusted by turning over the cutting head. LOWEST K This symbol visible • Disconnect from the mains electricity supply and wait until the cutting head has stopped rotating. Turn your product upside down. L 1 • To Remove the Cutting Head and Fan (L) Hold the fan firmly and twist the cutting head anti- clockwise as illustrated. Hold the cutting head in the centre and remove as illus
ページ6に含まれる内容の要旨
Grassbox • For optimum performance your product is P grassbox is full designed to be used with the grassbox fitted. Grassbox full Indicator (P) • IMPORTANT The machine must be switched on for the grassbox is empty grassbox full indicator to operate. 1. When the ball reaches the top of the indicator win- dow, it is time to empty the grassbox. See figure N. 2. When the ball is NOT visible in the indicator win- dow, grass is being collected. See figure N. Emptying the Grassbox (Q) Q • Stop the pr
ページ7に含まれる内容の要旨
Caring W • It is very important that you keep your product clean. Grass clippings left in any of the air intakes or under the hood could become a potential fire hazard. Cleaning (W) • USE GLOVES 1. Remove grass from under the hood with a piece of wood or similar. 2. Using a soft brush - remove grass clippings from all air intakes, the roller, grassbox and grassbox lid. 3. Remove the cutting head, see Figure L, to gain access to the fan and clean with a soft brush. 4. Wipe over the surface of you
ページ8に含まれる内容の要旨
Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life. • Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling. • Awareness of the environment must be considered when disposin
