ページ1に含まれる内容の要旨
SAMURAI 1000XT
AUTO-
MATIC SPEED
CONTROL FOR
YOUR SAFETY AND
COMFORT
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
360º Carton Contents Cable Shoulder Management Harness Location Electric Cable with moulded on plug Handle Lock-off Clamp button Instruction Cable Management Manual Adjustable Shoulder Switch Harness Handle Hexagon Drive Tool Guard (with bolt and nut) Steady Handle IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct:- Telephone : 0870 609 1901 Fax
ページ3に含まれる内容の要旨
3. Do not use the product if the electric cables are non-slip footwear. 5. Do not walk backwards when operating, you could damaged or worn. trip. Walk never run. 4. Immediately disconnect from the mains electricity sup- 6. Keep cutting head below waist level. ply if the cable is cut, or the insulation is damaged. 7. Never operate the product with damaged guards or Do not touch the electric cable until the electrical sup- without guards in place. ply has been disconnected. Do not repair a cut o
ページ4に含まれる内容の要旨
Assembly Instructions A Switch Handle and Handle Tube Assembly (A), (B) & (C) 3 4 1. Loosen the four bolts on the Handle Clamp (A). 2 1 B1 2. Insert the Switch Handle and the Steady Handle into the holes at the side of the Handle Clamp (B1 Right Handed) (B2 Left Handed) - using the Hex Drive Tool to turn the switch handle (B3) B3 B2 C 3. Adjust the Handles to the most comfortable operating position by moving the Handle Clamp up or down the tube. 4. Secure the Handle Clamp by tightening the 3 4 f
ページ5に含まれる内容の要旨
Assembly Instructions cont’ Cable Restraint J1 J2 1. Form loop in mains cable and push the loop through the slot (J1). 2. To secure, position loop over the hook and pull the cable back through the slot (J2). Adjustable Shoulder Harness 1. Attach the clip on the Shoulder Harness to one of the holes in the Shoulder Harness Location (K1) to enable the correct and most comfortable balance when using the product with the harness fitted across the body (K2) Line Cutter Cover 1. Remove the cover on the
ページ6に含まれる内容の要旨
Cutting Head Q To replace nylon line. For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Husqvarna Outdoor Products stockists. 2 To fit spool and line complete: 1. Remove the Cap (Q1) and Spool Holder (Q2) 2. Remove old spool.(R) 1 3. Place new spool into spoolholder.(R) 4. Release one line from cleat (W). 5. Secure line into eyelet (S1). R Cap 6. Repeat for second line. 7. Refit the Spoolholder and fit the Cap ens
ページ7に含まれる内容の要旨
Maintenance • WARNING 5. Inspect the product carefully, especially the Disconnect from the mains electricity sup- parts of the cutting head. ply, before attempting any maintenance or 6. If your product is damaged in any way con- adjustment. Cutting head continues to tact your local approved service centre. rotate after the trimmer has been • Never use a damaged product. switched off. Keep fingers and hands 7. Store in a cool, dry place and out of reach of clear of the line cutter on leading ed
ページ8に含まれる内容の要旨
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Remove cap and spool, free line Is the line fed out and visible? LINE NOT FEEDING No and re-fit spool and cap. SEE Has line been removed from OR “CUTTING HEAD” cleat? LINE TOO SHORT The line may be jammed on the OR Is the automatic line feed work- spool. Rewind line to remove No ing? TRIMMER VIBRATES crossed loops. Check that line is in correct section o
ページ9に含まれる内容の要旨
Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture Failures not covered by guarantee within the guarantee period, Husqvarna Outdoor Products, * Replacing Nylon Line. through its Authorised Service Repairers will effect the repair or * Failures as a result of not reporting an initial fault. replacement to the customer free of charge providing: * Failures as a result of sudden impact. (a) The fault is reported directly to the Authorised Repairer. * Failures
