ページ1に含まれる内容の要旨
POWER TRIM
600 HD
Original Instructions
For all customer enquiries or for replacement parts, contact:-
01325 300303
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
360º 1 Carton Contents Switch Handle Steady Handle Tube Trimmer Head Instruction Electric Cable with Manual moulded on plug Guard IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct Telephone : 01325 300303, Fax : 01325 302530 Safety If not used properly this trimmer can be dangerous! This trimmer can cause serious injury to the opera- tor and others, th
ページ3に含まれる内容の要旨
2 4. Immediately disconnect from the mains electricity sup- trip. Walk never run. ply if the cable is cut, or the insulation is damaged. Do 6. Keep cutting head below waist level. not touch the electric cable until the electrical supply 7. Never operate the trimmer with damaged guards or has been disconnected. Do not repair a cut or dam- without guards in place. aged cable. Replace it with a new one. 8. Never fit metal cutting elements. 5. Your extension cable must be uncoiled, coiled cables
ページ4に含まれる内容の要旨
3 Assembly Instructions A1 A2 Assembly of Switch Handle to Tube (A1) Ensure that the internal cable is not twisted. 1. Insert the tube into the switch handle. 2. Push until it clicks into position. ENSURE THAT THE TUBE IS FULLY LOCATED BY ATTEMPTING TO REMOVE IT. Assembly of Trimmer Head to Tube (A2) Ensure that the internal cable is not twisted. 1. Insert the tube into the trimmer head. 2. Push until it clicks into position. ENSURE THAT THE TUBE IS FULLY LOCATED BY B1 B2 ATTEMPTING
ページ5に含まれる内容の要旨
How to trim and edge G H WARNING The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTE- NANCE OR ADJUSTMENT. BEFORE USE J Make sure that both lines are fed out. Make sure
ページ6に含まれる内容の要旨
Manual line feed M To manually feed the nylon line (M) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed but- ton, whilst gently pulling on one of the lines until the line reaches the line cutter. 3. When the required amount of line is fed out, gently pull on the second line (there is no need to press the manual line feed button again). 4. If the line extends past the line cutter, too much line has been fed out. 5. If too much line is fed out, remove
ページ7に含まれる内容の要旨
Maintenance R WARNING Disconnect from the mains electricity supply, be- fore attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Power Trim After you have finished using your Flymo Power Trim fol- low the procedure below: S AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM MAINS AND KEEP FEET AWAY FROM THE SWITCH LEVER WHEN: CLEANING AROUND THE I
ページ8に含まれる内容の要旨
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No ing? SEE “MANUAL LINE FEED” OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. SEE OR cleat? “CUTTING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is the
ページ9に含まれる内容の要旨
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category............................Electric Lawn Trimmer Type(s) ............................PTHD26 Identification of Series.......See Product Rating Label Year of Construction..........See Product Rating Label Conforms to the essential requirements & provisions of the following EC Directives: 98/37/EC (until 31.12.09)
