ページ8に含まれる内容の要旨
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No SEE “MANUAL LINE FEED” ing? OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT No Has line been removed from and re-fit spool and cap. SEE OR cleat? “CUTTING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is the
ページ9に含まれる内容の要旨
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category............................Electric Lawn Trimmer Type(s) ............................PTXT25 Identification of Series.......See Product Rating Label Year of Construction..........See Product Rating Label Conforms to the essential requirements & provisions of the following EC Directives: 98/37/EC (until 31.12.09)
ページ1に含まれる内容の要旨
Power Trim
500 XT
Original Instructions
For all customer enquiries or for replacement parts, contact:-
01325 300303
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
360º 1 Carton Contents Switch Handle Steady Handle Tube Instruction Manual Electric Cable with moulded on plug Safety- Guard Trimmer Head Plant and Tree Guard IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct Telephone : 01325 300303 Fax : 01325 302530 Safety If not used properly this trimmer can be dangerous! This trimmer can cause serious injury to th
ページ3に含まれる内容の要旨
2 7. Do not pull cable around sharp objects. other than grass. 8. Always switch off at the mains before disconnecting 8. Never operate the trimmer with damaged guards or any plug, cable connector or extension cable. without guards in place. 9. Never pull on the cable to disconnect any of the plugs. 9. Never fit metal cutting elements. 10.Switch off, remove plug from mains and examine electric 10.Keep hands and feet away from the cutting means at supply cable for damage or ageing before winding c
ページ4に含まれる内容の要旨
3 Assembly Instructions cont’ B1 B2 Safety Guard Assembly (B1) & (B2) 1. Locate the safety guard over the cutting head. Ensure the nylon line is fed through the hole in the safety guard as illustrated in fig B1. 2. Push into location and turn safety guard in the direc- tion illustrated in Fig B2, until a click is heard and the safety guard is securely locked in position. ENSURE THE SAFETY GUARD IS SECURELY IN PLACE BY ATTEMPTING TO TWIST GUARD. Steady Handle Assembly (C) 1. Depress the two bu
ページ5に含まれる内容の要旨
How to use G H1 WARNING The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTE- NANCE OR ADJUSTMENT. BEFORE USE Make sure that both lines are fed out. Make sure motor
ページ6に含まれる内容の要旨
Using the Shrubbing position N 1. By pressing the lever (N1) with your foot, the handle can be lowered into three different positions to enable the use of the product under shrubs and low obstacles (P). P 1 Manual line feed To manually feed the nylon line (Q) Q 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on one of the lines until the line reaches the line cutter. 3. When the required amount of line is fed out, gentl
ページ7に含まれる内容の要旨
Maintenance V WARNING Disconnect from the mains electricity supply, be- fore attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your product W After you have finished using your product follow the pro- cedure below: AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM MAINS AND KEEP FEET AWAY FROM THE SWITCH LEVER WHEN: CLEANING AROUND THE IN- SIDE OF T
