ページ1に含まれる内容の要旨
EasiCut 420/EasiCut 450/
EasiCut 500/EasiCut 510
EasiCut 600XT
Original Instructions
EasiCut 420/450/500/510
EasiCut 600XT
For all customer enquiries or for replacement parts, contact:-
01325 300303
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
ページ2に含まれる内容の要旨
Carton Contents EasiCut 420/450/500/510 Handguard blade cover instruction manual belt clip EasiCut 600XT Handguard blade cover instruction manual belt clip IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct Telephone : 01325 300303 Fax : 01325 302530
ページ3に含まれる内容の要旨
Safety If not used properly this product can be dangerous! This product can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warning and safety instructions in this manual and on the product. Explanation of Symbols on your product Remove plug from the mains immediately Warning. if the cable is damaged or cut. Do not expose to rain
ページ4に含まれる内容の要旨
Safety cont’ use. Many accidents are caused by poorly hedge trimmer. maintained power tools. 6. Always switch off at the mains before disconnecting f) Keep cutting tools sharp and clean. Properly any plug, cable connector or extension cable. maintained cutting tools with sharp cutting edges 7. Switch off, remove plug from mains and examine are less likely to bind and are easier to control. electric supply cable for damage or ageing before g) Use the power tool, accessories and tool bits winding
ページ5に含まれる内容の要旨
Cables CABLES 1. No earth required. Our products are double insu- IMPORTANT lated to EN60745 and under no circumstances 2 Use only 1.00mm size cable up to 40 metres length should an earth be connected to any part of the prod- maximum. uct. Maximum rating : 2. Ensure the mains voltage suits your product 2 1.00mm size cable, 10 amps 250 volts AC. 3. IMPORTANT! • YOUR HEDGETRIMMER IS SUPPLIED WITH The wires in the mains lead are coloured in accor- CABLE WIRED DIRECTLY INTO THE PRODUCT. d
ページ6に含まれる内容の要旨
Before Use B1 B2 B3 C1 C2 D Before starting your hedge trimmer. 4. Form a loop in the mains cable and push the loop Securing the cable in the Belt Clip helps keep the through the hole in the Belt Clip (C1) ensuring the coil cable away from blade. in the cable is close to the clip. 5. To secure, position the loop over the hook and pull 1. Push up the hook on the Belt Clip (B1) 2. Place the rear section of the Belt Clip behind your back (C2). belt (B2) 6. Connect to mains and switch on 3. Push d
ページ7に含まれる内容の要旨
How to Use How to Use your hedge trimmer 1. Inspect area to be cut before each use - remove ob- M jects which can be thrown or become entangled in the cutting blades. 2. Always keep the hedge trimmer in front of your body. Hold handle firmly with both hands and stand in a se- cure and stable position. 3. Allow the cutting blades to reach full speed before en- tering the material to be cut. 4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc. 5
ページ8に含まれる内容の要旨
Environmental Information • Awareness of the environment must be considered when tronic equipment. By ensuring this product is disposed disposing of ʻend-of-lifeʼ product. of correctly, you will help prevent potential negative con- • If necessary, contact your local authority for disposal sequences for the environment and human health, information. which could otherwise be caused by inappropriate waste handling of this product. For more detailed information The symbol on the product or
ページ9に含まれる内容の要旨
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category............................Hedgetrimmer Type(s) ............................EC420, EC450, EC500, EC510, EC600 Identification of Series.......See Product Rating Label Year of Construction..........See Product Rating Label Conforms to the essential requirements & provisions of the following EC Directives: 98/37/E
