ページ1に含まれる内容の要旨
BIG Button phone
Userfriendly
Guide
ページ2に含まれる内容の要旨
Lift flap
ページ3に含まれる内容の要旨
Handset hook S (secrecy) button When the phone has been Held down, this button allows you to speak wall-mounted it keeps the to someone in the same room without the At a glance handset in place. person on the other end of the line hearing your conversation. Handset park When the BIG Button phone is wall- Indicator light mounted, you can hook the handset This will flash when the phone rings. on this if you need to temporarily move away from the phone. One-touch memory buttons R (recall) button E
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Introduction Your BIG Button phone is designed for ease of use and made to the high standards set by BT We thank you for making Contents the right choice and expect that your phone will give you many years At a glance 2 of quality service. Introduction 3 Please read the Installing your instructions carefully BIG Button phone 4 before use, and keep this User Guide for future Using your reference. BIG Button phone 8 This user guide is Wall-mounting 14 available in the following Technical formats
ページ6に含まれる内容の要旨
Installing your BIG Button phone The emergency services IMPORTANT can be contacted in the Check that your UK by dialling 999. You BIG Button phone is may also dial 112, which complete. When you is valid in any country unpack you should that is a member of the find: European Community. BIG Button phone with You may not be able to telephone line cable make an emergency call attached and a plinth in certain situations: 3 • If the telephone line is disconnected. • If there is a fault on the line f
ページ7に含まれる内容の要旨
Plan where you will Warning put your BIG Button phone Your BIG Button phone is only designed to be operated in a normal domestic or office environment. It should It should be within two metres of a phone not be used in bathrooms or socket. near water. Do not stand it on carpets or other similar Plug your BIG Button surfaces that generate phone into the wall fibres as this may reduce socket the ringing sound and clog inside mechanisms. Your BIG Button phone can be positioned in three alternativ
ページ8に含まれる内容の要旨
Ringer volume Ringer tone select Switch found on base of Switch found on base of phone. phone. Set the volume of the This switch allows you to ringer to select the pitch required Either High, Low or Off. for the ringer. R1: For a low pitched tone. R2: For a medium pitched tone. R3: For a high pitched tone. 6 Installing
ページ9に含まれる内容の要旨
Time Break Recall Amplify selection and Earth Recall selection Switch found on base of Switch found on base of phone. phone. Choose between either Your phone will already incoming or outgoing be set to TB. If you are a settings. Incoming makes residential customer this the caller’s voice louder. will help you to use some Outgoing makes your Network Services such voice louder at the other as Call Waiting, as long end of the call. as you subscribe to this service. Using the Amplify button Call BT
ページ10に含まれる内容の要旨
Using your BIG Button phone To redial the last To make a call number dialled 1 Lift the handset. 1 Lift the handset and listen for a dialling tone. 2 Press the REDIAL button. The phone will 2 Dial the number you automatically redial the require. last number dialled. To end the call, replace the handset. To receive a call When the phone rings pick up the handset and speak. 8 Using
ページ11に含まれる内容の要旨
1 Lift up the handset. To store phone numbers in the ‘one-touch’ memory 2 Push label to the left. 3 Press the STORE button. Your BIG Button phone has three ‘one-touch’ memory buttons. 4 Press the ‘one-touch’ These allow you to store memory button under three numbers that may which you wish to store be dialled at the touch of the number. a button. These should be your most commonly used numbers. 5 You can store a phone Enter the number you number under each wish to store. of these buttons and d
ページ12に含まれる内容の要旨
Each memory location To store phone can store a maximum of numbers in the 21 digits (numbers). Quickdial memory You can write the name of the person with which you wish to associate Your BIG Button phone the number on the label also has 10 ‘two-touch’ provided or perhaps insert memory locations in the a small photo. keypad, which are dialled by using the QUICKDIAL To dial a number button. stored in the ‘one-touch’ 1 Lift the handset. memory 2 Lift the handset. 1 Press the STORE button. 2 3 Pre
ページ13に含まれる内容の要旨
5 Enter the number you Quickdial want to store. memory label 6 Press the STORE button. Use the memory label to keep a record of which 0-9 location code you have used for each The phone number is now number. stored. Please replace the handset. A large print version of this is included at the end Repeat these steps for of this user guide. See any other numbers you ‘Quickdial memory label’ want to store, using a on page 19. different 0-9 location for each one. To dial a number stored in the Store
ページ14に含まれる内容の要旨
3 Press the 0-9 location To change under which the number numbers stored in you require is stored. the memory 0...9 To change numbers The phone number is stored in the memory, dialled automatically. simply repeat the process of storing the original numbers but enter the You may hear the new number. The number telephone exchange say stored in that location is ÔPlease hang up and try automatically replaced by againÕ. This message does the new number. NOT necessarily mean your storing of numbers
ページ15に含まれる内容の要旨
To increase the amplification press the To use your + button. Amplify button To decrease, press the – button. Press the Amplify button to turn amplification on. To return to the normal setting, just press the Amplify – and + allows amplify button again. you to select an appropriate setting The red LED will light up between normal and to show when amplify is maximum. switched on. There are a total of four settings. The standard setting is for the amplify to be off. The setting last used on
ページ16に含まれる内容の要旨
Wall-mounting 1 Your BIG Button phone Drill two holes (diameter can be wall-mounted 8mm) for the screws using the screws and wall vertically apart. Insert plugs provided. the wall plugs provided (if required). Use the plinth of the WALL PLUG SCREW BIG Button phone as your wall-mounting template to pencil on the wall a guide WALL for the drill holes. 102 mm Before you wall-mount 2 Drive the screws into the your BIG Button phone, wall, leaving about 5mm check that: free on which to hang the • the
ページ17に含まれる内容の要旨
4 6 Rotate the handset hook Feed the phone line 180°, so that you can through the bottom of hang up the handset the wall mounted plinth when the phone is wall- to allow the cable to rest mounted. flat against the wall. 5 Hang the holes on the back of the phone over the screwheads and gently pull the phone downward to make sure it is securely in place. 15 Wall-mounting
ページ18に含まれる内容の要旨
Technical information Connection How many phones information can you have? All items of telephone Your BIG Button phone equipment have a Ringer may be connected to Equivalence Number public networks in the (REN), which is used to United Kingdom. calculate the number of items that may be It may also be connected connected to any one to switching systems that telephone line. Your BIG use tone (MF) signalling, Button phone has a REN with timed break or of 1.5. A total REN of 4 is earth recall. If
ページ19に含まれる内容の要旨
The goods have not been For your records tampered with or repaired by anyone other than BT, its staff or agents. Date of purchase: If a fault does occur in this product, and you Place of purchase: bought the unit yourself, provided that you return it to the place of purchase Serial number: and produce your receipt, (on base of the it will either be repaired telephone) or replaced free of charge. The terms and conditions of this Purchase price: guarantee do not affect your statutory rights. (for
ページ20に含まれる内容の要旨
Index Amplify 7,13 Dialling, one-touch 10 Dialling, Quickdial 11 Earth Recall 7 Emergency numbers 4 Guarantee 17 Labels,Quickdial 11,19 Make a call 8 Memory, Quickdial 10 Memory,changing 12 Memory,one-touch 9 Quickdial 10,11 R button 12 Receive a call 8 Redial 8 REN 16 Ringer tone 6 Storing numbers 9,10 Switchboards 16 Telephone socket 5 Timed Break Recall 7 Volume, ringer 6 Volume, increasing 6,7 Wall mounting 14 18 Index
