ページ1に含まれる内容の要旨
SIP IP Phone
-- with PSTN Connectivity
User’s Manual
ページ2に含まれる内容の要旨
Table of Contents Chapter 1 Overview of the VIP-150T ...............................................................................................1 1.1 Hardware Overview................................................................................................ 1 1.1.1 Front View and Keypad function .................................................................. 1 1.1.2 Back View ...........................................................
ページ3に含まれる内容の要旨
4.12 [sysconf] command ............................................................................................ 35 4.13 [sip] command.................................................................................................... 36 4.14 [security] command ............................................................................................ 37 4.15 [voice] command ..........................................................................
ページ4に含まれる内容の要旨
Chapter 1 Overview of the VIP-150T VIP-150T is a full-featured IP-based telephone set via Ethernet base communication. Over the office LAN connection, it provides IP-PBX solution such as station-to-station call, IP call and local PSTN/PBX Extension call via PSTN Gateway. VIP-150T provides two 10/100BaseT switch/hub RJ-45 ports allow connecting to office LAN and PC simultaneously. It is compatible with ADSL or Cable Modem provided by ITSP, ISP o
ページ5に含まれる内容の要旨
♦ LCD: 2 lines, 24 character Dot Matrix display. ♦ C: Jump out current LCD menu. ♦ ç : Move to previous selection or clear previous data. ♦ è : Move to right or next selection. ♦ OK: Press OK to confirm the modification. ♦ Direct Line (DL) Button 1 – 10: User press DL button after off-hook to do speed dial according to phone book data from 1-10 (please refer to LCD configuration-3.Phone Book; Advanced Configurations via Telnet- 5.[pbook] command, o
ページ6に含まれる内容の要旨
♦ HOLD: To hold a call, after press HOLD button, both sides will hear hold tone. ♦ SPEED: Press SPEED and number (Phone book index) after off-hook can do speed dial according to phone book data (please refer to 3.LCD configuration-6. Phone Book or Advanced Configurations via 4.Telnet- 5.[pbook] command). ♦ FORWARD: Forward an incoming call to another IP device. (Please refer to LCD configuration-Forward Type) (**) ♦ MESSAGE and its indicated LED
ページ7に含まれる内容の要旨
1.1.2 Back View ♦ DC 9V: DC 9V power input outlet ♦ LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable. ♦ PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable ♦ Line: RJ-11 connector, connected directly to the PSTN analog line. There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port. When network status is regular, LED of LINK/ACT will light on; when ? VI
ページ8に含まれる内容の要旨
1.2 Software Features and Specification Application: l ISP/ITSP (Internet Telephony Service Provider) l IP-PBX with office telephony services l Multi-nation enterprise communication l SOHO Telephony Calling Features l Call Hold l Call Transfer l Call Forward (**) l 10 sets last number Redial l Ten configurable speed dials Network Supported l Fixed IP l Dynamic Host Configuration Protocol (DHCP) l PPPoE connection (When PPPoE disconn
ページ9に含まれる内容の要旨
Provisioning and Configuration l SIP (RFC3261) compliance l LCD configuration password protection l Provide Proxy Mode or Peer-to-Peer Mode (Non Proxy Server needed) selection l Ring tone, Speaker and Handset volume adjustable l Dial path selection (PSTN or IP mode) l Support DNS server inquiry Management Features: l Software Upgrade: TFTP/FTP download l Three easy ways for system configuration - LCD Front Panel - Web Browser - TELNET
ページ10に含まれる内容の要旨
Chapter 2 Configuring the VIP-150T through LCD Phone menus 1. After any configuration is made for the VIP-150T, user has to do Reboot in the selection 7 “Reboot”. ? 2. We suggest user to set IP address via LCD menu 5→2.3.4.5 first, then Note: go to chapter 3 to do other detail configurations via web browser. 2.1 Initialize VIP-150T 1. When power on the VIP-150T, the LCD screen shows as below. Now VIP-150T is running Boot sector program.
ページ11に含まれる内容の要旨
mode. (**) VIP-150T PSTN 10:10:10 AM 6. Press ç or è to enter configuration mode then press OK button to enter sub menus; press C can jump out current menu to previous level. 1. Call List (**) 2. Forward Type 3. Phone Book 4. Ringer Settings 5. Network 6. Advanced Settings (protected by password) 7. Reboot 2.2 LCD Menu Configuration User can set the following configurations by LCD keypad. 1. Press TRANSFE
ページ12に含まれる内容の要旨
2. Forward Type (**) There are 3 selections in Forward type, user must select under which condition to forward calls. (1) Busy When VIP-150T is in busy status, the incoming call will be forwarded to the assigned phone number. A. Activate Enter a forwarded phone number to activate busy forward function. B. Deactivate Deactivate Busy Forward function. (2) No Response When VIP-150T hasn’t been picked up for around 10 seconds, the incoming c
ページ13に含まれる内容の要旨
Add a new record of name, telephone number, and IP address of the phone address book. 4. Ringer Settings 1. Volume User can adjust ring volume by press ç or è on the keypad to decrease or increase ringer volume. 2. Style There are three tone styles for VIP-150T. Move the “>” symbol by press ç or è on the keypad to select the tone style preferred, then press OK to confirm it. 5. Network 1. Information User can press ç or è to check
ページ14に含まれる内容の要旨
(3) Auto Re-connect Choose ON or OFF to enable or disable this function. If user enables this function, after PPPoE disconnected, VIP-150T will automatically reboot to re-connect, and after reboot, if VIP-150T still can’t connect with server, VIP-150T will keep trying to connect. On the other hand, if user disables this function, VIP-150T won’t reboot and keep trying to connect. 8. SNTP Configuration (1) SNTP Mode: User can set SNTP function t
ページ15に含まれる内容の要旨
Select SIP connection mode to be peer-to-peer mode or Proxy mode. (2) Proxy A. Proxy Set Proxy IP address or Domain Name. B. Outbound proxy Set Outbound Proxy IP address or Domain Name. C. Proxy port Set Proxy port for VIP-150T to send messages. D. Expire (in seconds) Set expire time of registration, in the duration of 2/3 expire time, VIP-150T will re-register to Proxy Server again. (3) User Info A. User Name Set User Name of VIP-150T to reg
ページ16に含まれる内容の要旨
(5) Start to Upgrade Select YES or NO to start upgrade. After download is finished, press OK then VIP-150T will ask if need to reboot. (**) (6) Firmware Version Show versions of all software and hardware. (**) ? Download via LCD command can only upgrade new application rom file. Note: 2. LCD Menu Password Set entry password of phone LCD menu. 7. Reboot Reboot machine. It is necessary and important for user to reboot VIP-150T after any
ページ17に含まれる内容の要旨
Chapter 3 Configuring the VIP-150T through Web Pages The HTTPD web management interface provides user an easier way to configure rather than command line method through TELNET. The configuration function and steps are similar with the way through command line. Please refer to the chapter 4- Configuring the VIP-150T through Telnet command lines for more detail information. Below is a guide for user to configure via web interface. Step 1. Bro
ページ18に含まれる内容の要旨
Step 3. Enter the web interface main screen After enter login name and password, user can see web interface main screen as below. Step 4. Start to configure Most important items are Network Interface, SIP Configurations, and Phone Book (in Peer-to-Peer mode). Please remember to configure these commands before start to work with VIP-150T. After change any settings, please remember to reboot VIP-150T so that ? changes can take effect.
ページ19に含まれる内容の要旨
1. Network Interface Please refer to chapter 4.9 [ifaddr] command. - IP Address: Set IP Address of VIP-150T - Subnet Mask: Set the Subnet Mask of VIP-150T - Default routing gateway: Set Default routing gateway of VIP-150T - Get IP Mode: User has to set VIP-150T to use which network mode. 1. Fixed IP: User has to assign a fixed IP to VIP-150T. 2. DHCP: When DHCP function enables, VIP-150T will automatically search DHCP server after reboot.
ページ20に含まれる内容の要旨
- SNTP: Enable / Disable the Simple Network Time Protocol function PLANET VIP-150T User’s Manual 17
