ページ1に含まれる内容の要旨
i2022 ISDN Teleset
8-20-04
i2022 Series
ISDN Teleset
User’s Guide
i2022 Comcodes
Black: 300130358
004-LUC-I0005-B
Misty Cream: 300131679
ページ2に含まれる内容の要旨
i2022 ISDN Teleset Mandatory Customer Information Federal Communications Commission (FCC) Requirements This equipment complies with Part 68 of the FCC Rules. The FCC registration information is located on a label affixed to the bottom of the Teleset. If requested, you must provide the telephone company with the following information: Facilities interface Code (FIC) 02IS5, Service Order Code 6.0Y, and Registered Jack RJ-49C*. When the i2022 Teleset is equipped with an S Interface Modul
ページ3に含まれる内容の要旨
i2022 ISDN Teleset INTRODUCTION ................................................................................................................................................................. 2 ISDN i2022 S/T Teleset ...........................................................................................................................................................2 About This Manual ....................................................................................................
ページ4に含まれる内容の要旨
i2022 ISDN Teleset TABLE OF FIGURES FIGURE 1: LINE AND POWER JACKS............................................................................................................................................ 5 FIGURE 2: NT1 LEADS .............................................................................................................................................................. 6 FIGURE 3: S INTERFACE MODULE ...........................................................................
ページ5に含まれる内容の要旨
i2022 ISDN Teleset FEATURES The i2022 Teleset offers an extensive list of features. They include the following: Cross-Compatibility ® The Telesets work with several different switches: the Lucent Technologies 5ESS (Custom and National ISDN), the ® ® ® Nortel DMS-100 (National ISDN), the Siemens EWSD (National ISDN), and the AG Communication Systems GTD-5 . Programmable Features and Options An extensive array of options/features may be provisioned via menus. Programmable Hardkeys
ページ6に含まれる内容の要旨
i2022 ISDN Teleset Call Timer On each new call, the timer displays the elapsed time of the call. Placing a new call resets the timer for the new call. Headset Jack Inserting the headset plug into this jack enables the headset, and disables the speakerphone. The i2022 Teleset contains an amplifier controlled by the volume key. Network Features Your Teleset can provide advanced network features. Such features as Call Forwarding, Auto-Callback and Call Pickup, may be available through y
ページ7に含まれる内容の要旨
i2022 ISDN Teleset ISDN INTERFACES A little background information sometimes helps. Your ISDN service comes to you over ordinary telephone line wiring. That makes it less expensive and simple to install. There are a number of interfaces defined in Basic Rate ISDN. The most common of these interfaces are designated U, S, and T. The letters U, S and T do not mean anything, they are reference points. Your service provider (telephone company) will normally provide a 2-wire connection, cal
ページ8に含まれる内容の要旨
i2022 ISDN Teleset Figure 2: NT1 Leads PS1/PS2 SWITCH SETTINGS The i2022 requires PS2 power. Always leave the PS1/PS2 switch in the PS2 position. Figure 3: S Interface Module Power Switch PS 2 PS 1 NOTE: PS 2 is the mandatory Power Switch setting. TERMINATING RESISTOR SETTINGS Options 1 2 3 4 5 Open OFF OFF - - - 100 Ω ON ON - - - The default setting is 100 Ω (ohm) termination Table 2 Powering the i2022 Locally The i2022 can use a significant amou
ページ9に含まれる内容の要旨
i2022 ISDN Teleset Pin 4-5: S/T Interface Pin 4-5: S/T Pin 3-6: S/T Interface Interface Pin 3-6: S/T IN OUT Interface Pin 7-8: Power TIS-1215B Power Adapter AUX AC 120V Lucent EM-32 EM-32 i2022 Figure 4: Using Lucent 1215B Power Supply NOTE: Because of the high power requirements of the 2022, it is recommended powering telesets equipped with EM-32 modules locally. U Interface U Interface S/T Interface S/T Interface Pin 4-5: S/T
ページ10に含まれる内容の要旨
i2022 ISDN Teleset TERMINATING RESISTORS The i2022Teleset S Interface module has built-in Terminating Resistors. The Terminating Resistor switches are located on the top of the Interface Module. When the switches are in the ON position, the Terminating Resistors are installed. The value of the resistors is 100 Ohms. NOTE: The S Interface Module must be removed from the Teleset to gain access to the option switches. POINT-TO-POINT CIRCUITS A point-to-point application typically has
ページ11に含まれる内容の要旨
i2022 ISDN Teleset In the following application, the NT1 is equal in distance to both i2022 phones. The Terminating Resistors are set to “On” at one of the phones and at the NT1. Figure 8: Equal Distance Telesets i2022 EQUIPPED WITH A U INTERFACE MODULE The i2022 is available with an optional U Interface Module. Actually, the U Interface Module is an NT1 device, therefore, the Teleset does not require an external NT1 device. Fig. 9 shows the i2022 equipped with a U Interface Module
ページ12に含まれる内容の要旨
i2022 ISDN Teleset 1. If the S Interface Jack is not used and the i2022 is the only device, set the Terminating Resistor switches to 50 Ω. 2. If there is a device connected to the S Interface, set the Terminating Resistor switches to 100 Ω. 3. If the S Interface Jack is not used and the i2022 is the only device, set the Timing Switch to Adaptive. 4. If there is a device connected to the S Interface, and if the distance between the U Interface Module and the point at which the device is conn
ページ13に含まれる内容の要旨
i2022 ISDN Teleset INSTALLING THE LOGO PLATE ASSEMBLING THE i2022 Inserting and removing the modules The i2022 Teleset requires either an S Interface module or a U Interface Module. There are also optional Data Modules available. There are two slots on the bottom of the i2022. The S and U modules fit in the left slot (as viewed from the rear with the i2022 upside down) and the Data Modules fit in the right slot. Different size connectors prevent the modules
ページ14に含まれる内容の要旨
i2022 ISDN Teleset SOFTKEYS Directly below the display are four softkeys, vertically-oriented to the display. The location of these keys corresponds to menu choices that appear directly above them in the LCD window. For example, pressing the softkey below the “clock” menu reveals the options for setting the time of day and date. They are called softkeys because their function changes according to the menu. In one menu a key may set the time, while in another menu the same
ページ15に含まれる内容の要旨
i2022 ISDN Teleset Example: Press the softkey under Directory - shown below by highlighting (bold type) the word “DIR” and highlighting the softkey below that menu item. Pressing the Directory softkey brings up the second menu with additional choices. In our example we chose Search next - shown in bold type. The selected menu items are shown in bold type for emphasis. The softkey under Search is highlighted to indicate the chosen softkey. Choosing Search returns the next screen, a
ページ16に含まれる内容の要旨
i2022 ISDN Teleset NOTE: You may abort the Auto-Install by pressing the Menu key at any time The Auto-Install programming choices are: Adjust Contrast – Select Yes or No. The i2022 may display a wait message and start a countdown. This is the T- Wait timer. NOTE You can abort the T-Wait countdown timer at any time by pressing the Speaker key or any touchtone keypad digit. SPID – If the switch supports Auto-SPID you will be prompted to choose a SPID. If your switch does not
ページ17に含まれる内容の要旨
i2022 ISDN Teleset If the switch supports Auto-SPID, the i2022 will display all of the SPIDs available on the line in the following format: If the SPID displayed is not the correct SPID for your application, press the Next key. Pressing the Detail softkey will display the SPID, the Primary Directory Number, and the Bearer Services assigned to the SPID. The detail information is as follows: 1 : SPID=84755547360101 DN=8475554736 Bearer: Speech Next Prev Select Prompt
ページ18に含まれる内容の要旨
i2022 ISDN Teleset Connecting the I2022- Manual-install 1. Assemble the i2022 NOTE: Make sure the logo plate is installed 2. Verify the PS1/PS2 switch located on the Interface Module is in the PS2 position. See page 6 for further information on setting the PS1/PS2 switch. 3. Verify the Terminating Resistor (TR) switch is set correctly. See page 8 for further information on setting the TR switch. 4. Connect one end of the eight-pin mounting cord to the ISDN Line-In jack on the bottom
ページ19に含まれる内容の要旨
i2022 ISDN Teleset 4. Up to twenty digits can be entered as the SPID. After entering the digits, press Save to enter into non-volatile memory. If an error is made use the Bkspc (backspace) key to edit. Enter the corrected digits and press Save. 5. Choose the Service you require. (Voice is the default) See Table 4. Serviced as Voice SPID1 = 84755547360101 [(P+D)=POTS+Data] POTS (P+D) Data MORE is flashing Press MENU to exit. When the SPID entr
ページ20に含まれる内容の要旨
i2022 ISDN Teleset Manually Programming Call Appearances Take a look at the layout of the Line and Call Appearance keys. These (32) keys are located on the far-right hand side of the phone. The upper-left-hand key is the default or primary key. This key must remain a Call Appearance key. All of the other 31 keys are programmable. It is important to check with your system administrator to see how your Teleset is provisioned at the switch. You will have at least one Directory Number (DN
