ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Congratulations on your purchase of the CL600 Emergency Connect Telephone from ClearSounds Communications™. Please read this User Manual carefully in order to get the very best results from your telephone. Keep the manual near the telephone for easy reference. Please visit our web site at www.clearsounds.com to: · Register your product It’s easy! Click on the Warranty Registration Tab, complete the form and click “submit”. It’s that simple! · Download additional manuals and troubles
ページ3に含まれる内容の要旨
WARNING: The CL600 Emergency Connect Telephone should be tested regularly to ensure proper delivery of your pre-recorded emergency message when activated by the Emergency Button or the Remote Band. This is your responsibility as the user of the product. WARNING: Using the CL600 does not guarantee that you will make contact or receive help. The CL600 is only an aid to assist you in calling for help. WARNING: Certain structures within the household may block the transmitter signal. It is up t
ページ4に含まれる内容の要旨
Table of Contents Product Overview Page 2 Limitation of Liability Page 2 Conditions For Use Page 2 Table of Contents Page 4 Features & Functions Top View Page 6 Left side, Right side & Back side Views Page 7 Handset & Bottom View Page 8 LCD Screen Page 9 Screen Display Page 9 Installation Steps Components Page 10 Installing the optional batteries Page 10 Phone mounting – desk & wall use Pages 11-12 Setting the dialing mode Page
ページ5に含まれる内容の要旨
Using the volume reset override Page 24 Using the outgoing speech volume Page 25 Using the last number redial Page 25 Using the flash button Page 25 Using the mute button Page 25 CL600 Caller ID Operation Viewing your Caller ID display Page 26 Viewing incoming calls Page 27 New calls / message waiting indicator Page 28 Remove call record(s) from Caller ID A specific call record Page 28 All call records Pages 28-29 Turn on the Call Waiting
ページ6に含まれる内容の要旨
Features & Functions Figure #2 11 26 5 1 2 3 4 27 8 6 7 9 10 25 12 24 13 14 15 28 16 31 X 29 30 Front 23 22 21 20 18 17 19 1. C (delete) button 13. PROG – Program (save) 21. FLASH button button 22. REDIAL button 2. (up) button 14. STOP – Cancels emer- 23. In use indicator 3. (down) button gency connect dial button 24. Speaker 4. OK (accept) button 15. – Active emergency 25. Large keypad 5. – Priority memory button connect dial button 26. Hook switch 6. – Priorit
ページ7に含まれる内容の要旨
Features & Functions Figure #3 2 3 Left side 4 5 1 Right side Back 11 10 9 8 7 6 1. Speakerphone volume adjustment 2. Antenna 3. Outgoing speech volume select switch (LO/NORMAL/HI) 4. Ringer Volume select switch (HI/LO/OFF) 5. Ringer / shaker / strobe select mode 6. Phone line jack 7. AC power adapter jack 8. Volume reset override switch (ON/OFF) 9. Optional bed shaker jack 10. Optional Audio/Neckloop jack (3.5mm jack) 11. Optional Telephone jack (2.5mm hands-free) 7
ページ8に含まれる内容の要旨
Figure #4 Bottom Handset 1234 1. Handset Boost button 2. Memory card to record speed dial numbers 3. Phone keyholes (mounts) 4. Battery compartment 8
ページ9に含まれる内容の要旨
Figure #5 2 1 3 4 9 8 5 7 6 Screen example (on hook position) 5. Validation button 1. Hours 6. UP / DOWN arrow buttons 2. Minutes 7. Cancel / Clear button 3. Power network icon 8. Month 4. Number of calls 9. Day OK button is used to confirm action or a choice on the screen. “UP / DOWN arrow” buttons are used to highlight or scroll through the menu. C button is used to cancel or confirm an action/entry or clear a stored Caller ID call. Your CL600 Phone has a screen with different icons, which
ページ10に含まれる内容の要旨
Installation Steps Installation of your ClearSounds™ CL600 Emergency Connect Phone is easy. There are some basic steps you need to take when you set-up your CL600 Emergency Connect Phone for the first time. 1. Check parts list. 2. Install (4) AAA Alkaline batteries (not included). Batteries are necessary in case of network power failure to save stored numbers in memory and are required for the “Phone Book” use. 3. Choose desktop or wall mount. 4. Set the dialing mode. 5. Set ringer and
ページ11に含まれる内容の要旨
PHONE MOUNTING INSTALLATIONS Choose a location for the CL600 Emergency Connect Telephone that is as central as possible in the house, while providing access to a modular jack and an AC outlet. The telephone may be placed on a shelf or table, or may be fixed to a wall using the mounting bracket. Plug the AC Adapter into the AC power back on the back of your phone, then into an electrical outlet or surge protector, if you are using one. NOTE: The adapter is required for the telephone to work c
ページ12に含まれる内容の要旨
5. Holding the phone slightly above the mounting screws on the wall jack, push the phone against the mounting screws so they are hooked into upper and lower key- hole slots on the back of the phone. Slowly slide the phone down until it snaps into place (See diagram #10). 6. Connect the handset coil cord (curly cord) to the handset and to the telephone. 7. Lift the handset and listen for a dial tone. If you hear a dial tone, your phone is ready to use. If there is no dial tone, check all your
ページ13に含まれる内容の要旨
PROGRAMMING THE RINGER & AUXILIARY ALERT Ringer Volume: You can adjust the ringer volume of your CL600 as high as 95+ dB. The ringer volume adjustment is located on the right side of the telephone. The settings are OFF, LO, HI, (See diagram #11). Your phone comes with the ringer switched to HI. In additional to volume, you can adjust the tone or melody of the ring. : Off, : Low, : Hi DIAGRAM #11 – Ringer Volume Switch Ring Style: Your CL600 Phone allows you to choose from four diff
ページ14に含まれる内容の要旨
Your CL600 Phone is equipped with a bright STROBE light, which flashes a very bright strobe when the phone rings (See diagram #13). It’s almost impossible to miss telephone calls when you select the Strobe Ringer. DIAGRAM #13 – Strobe Ringer (Flashing incoming call indicator) If you purchased the optional Bed Shaker, simply plug it into the shaker jack (See diagram #14) and place it between your mattress and box spring. Caution: For safety and correct functionality considerations, your CL600
ページ15に含まれる内容の要旨
To program your one-touch memory dial buttons please follow instructions below: 1. Lift the handset. 2. Press the PROG (program) button (See diagram #16). 3. Using the keypad, dial the number you would like to save, including “1” and the area code (if applicable). (See diagram #17). 4. Press one of the Priority or Memory Dial buttons (M1 – M6) located on top of the phone (See diagram #18). Each button can be programmed (or reprogrammed using the same procedure) for a phone number. 5. The Ca
ページ16に含まれる内容の要旨
CL600 Emergency Connect Phone Operation The ClearSounds™ CL600 Emergency Connect Phone allows you to ask for help con- veniently when there is an emergency. To activate the function, you need to preset the emergency connect SOS number and record an emergency connect SOS message, which will be heard by the person you contact. It is suggested to turn “ON” both the Remote Audio Monitoring & Auto On Hook features of the CL600. Programming emergency connect SOS number The CL600 Phone provides s
ページ17に含まれる内容の要旨
In the hook position, 1. Press the MUTE button. 2. Using the or arrow buttons, highlight <>. 3. Press the OK button to confirm. 4. Using the or arrow buttons, scroll to select <>. 5. Press the OK button. 6. Using the arrows button select << RECORD SOUND>>. 7. Press the OK button. 8. Record your emergency connect SOS message by speaking clearly into the speak- erphone at a distance less than 1 ft. You can record up to 10 seconds of speech. You may wish to use this mess
ページ18に含まれる内容の要旨
Phone will dial the next emergency connect SOS number automatically. NOTE: The friend, relative or neighbor whom you have chosen are required to have touch- tone phone service and a phone that will generate touch-tone code. Test the CL600 emergency connect phone 1. Make sure the phone numbers and your message have been entered. 2. Call your friends, family or neighbors to let them know you are going to test the CL600. Be sure that they understand that this is not a real emergency. 3. After
ページ19に含まれる内容の要旨
IMPORTANT: This feature will not work with answering machines or voice mail services. All answering machine or systems connected to the same phone number as your CL600 must be unplugged. Activate the Remote Audio Monitoring Feature In the hook position, 1. Press the MUTE button. 2. Using the or arrow buttons, highlight <>. 3. Press the OK button to confirm. 4. Using the or arrow buttons, scroll to select <>. 5. Press the OK button. 6. Using the arrow buttons select <
ページ20に含まれる内容の要旨
AUTO ON HOOK When the Auto On Hook feature is ON, Your ClearSounds CL600 will automatically discon- nect the line after 5 - 8 minutes if the phone is left off the hook. This will restore your line to be able to receive another call even if you leave the handset off the base. In the hook position, 1. Press the MUTE button to access the Programming Menu. 2. Using the or arrow buttons, highlight <> then press the OK button to confirm. 3. Using the or arrow buttons, scroll to selec
