ページ1に含まれる内容の要旨
USER’S MANUAL
Part 2
1
Two-Line Speakerphone 952
Fold open this manual for information about this
telephone’s installation and operation. Please
also read Part 1 — Important Product Information.
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
© 2001 Advanced American Telephones. All rights reserved.
Printed in China. Issue 1AT&T 7/01
ページ2に含まれる内容の要旨
INSTALLATION Batteries Before You Install Before using the telephone, you should install four NOTE: To use this product as a two-line phone, AA batteries (not included). If you are connecting you must have a two-line modular jack or two only Line 1 or only Line 2, use two batteries, as separate one-line modular jacks. To use both lines indicated on the bottom of the phone. If you are of a two-line telephone, your local telephone connecting both lines, use four batteries. company must provide tw
ページ3に含まれる内容の要旨
INSTALLATION Table/Desk 1 Connect line cord(s) to telephone. 4 Connect handset to telephone. • If you have a two-line jack, use only the line 5 Set Dial Mode. cord with the clear modular plugs on each This product comes set for touch tone dialing. end. Plug one end into the jack labeled L1 Make sure you choose the correct dialing method OR L1/L2 on the back of the telephone. (TONE or PULSE); dial pulse dialing will not work • If you have two separate jacks, use both line if you have touch tone s
ページ4に含まれる内容の要旨
INSTALLATION Wall 1 Connect bundled line cord(s) to the telephone. 3 Reverse handset tab. Leave the telephone line cord(s) bundled. To mount the telephone on a wall, you must reverse the handset tab. This tab holds the • If you have a two-line wall jack, use only handset when you hang up. the line cord with the clear modular plugs on each end. Plug one end into the jack labeled Hold down the switchhook, and slide the tab L1 OR L2 on the back of the telephone. up and out of its slot. Turn the t
ページ5に含まれる内容の要旨
TELEPHONE OPERATION Line Status Lights RINGER Volume Red on: line in use Set each switch Red flashing: line on hold to OFF, LO or HI. Green flashing: line ringing You can dial and answer calls normally with one or both Flash switches set Press F instead to OFF. of pressing the switchhook to activate services such Hold as Call Waiting or Press to put a line on 3-Way Calling. You hold. You can hang may have to press up the handset. To other buttons before return to the call, or after F as p
ページ6に含まれる内容の要旨
TELEPHONE OPERATION Automatic Redial Conference Calls This phone can automatically and repeatedly redial You can use both lines at the same time to set up the last number you called. Press L or l, then a three-way conference call. press a without lifting the handset or 1 Make or answer a call and press H. pressing K or h. You will hear the 2 Establish a call on the other line. numbers being dialed. When the call is answered, you 3 Press C. must either lift the handset or press K or 4 Hang up to
ページ7に含まれる内容の要旨
TELEPHONE MEMORY Storing Memory Numbers Directory Card 1 Lift the handset. Remove the plastic 2 Press and release P. cover and the directory card. 3 Enter the telephone Write your number you want to store telephone (up to 24 digits) or press numbers in the a to store the last spaces provided, number dialed.You will and write the hear a beep each time you telephone press a button. Press P numbers (or to store a three-second names) that you dialing delay. want to store in 4 Press and release a
ページ8に含まれる内容の要旨
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try Difficulty Storing Numbers In Memory the suggestions below. For Customer Service, • Review “Storing Memory Numbers” under visit our website at www.telephones.att.com or TELEPHONE MEMORY to make sure you are call 1 800 222–3111. Please retain your receipt pressing the correct sequence of buttons. as your proof of purchase. • If you are interrupted by a recorded announcement telling you to hang up (or a loud buzzing noise),
