ページ1に含まれる内容の要旨
HP Slate 21 All-in-One
User Guide
ページ2に含まれる内容の要旨
© 2013 Hewlett-Packard Development Company, L.P. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services . Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translate
ページ3に含まれる内容の要旨
About This Guide This guide provides information on setting up and using the HP Slate 21 All-in-One. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information. iii
ページ4に含まれる内容の要旨
iv About This Guide
ページ5に含まれる内容の要旨
Table of contents 1 Product features ............................................................................................................................................. 1 Front components ................................................................................................................................ 2 Rear components ................................................................................................................................. 3 2 Setting up the hard
ページ6に含まれる内容の要旨
Factory data reset .............................................................................................................. 21 Enabling input method editor (IME) .................................................................................................... 21 4 Safety and Maintenance Guidelines ............................................................................................................ 22 Important Safety Information ..................................................
ページ7に含まれる内容の要旨
1 Product features The HP Slate 21 All-in-One provides easy, simple access to the internet, and streaming views of media content (video, audio, photos). The all-in-one has an active matrix, thin-film transistor (TFT) panel. Features include: ● Android 4.2 operating system with multi-user support ● 54.6 cm (21.5-inch) diagonal viewable area LED display with 1920 x 1080 resolution ● 5 ms response time, 250 nits, 178/178 viewing angle, 1000:1 contrast ratio ● Tilt capability from 15 to 70 degrees ●
ページ8に含まれる内容の要旨
Front components Component Function (1) Webcam Records video and captures still photographs (2) Internal microphone Records sound (3) Webcam light On: The webcam is in use (4) Volume up button Increases volume (5) Volume down button Decreases volume (6) Brightness up button Increases display brightness (7) Brightness down button Decreases display brightness (8) Power button Turns the all-in-one on and off (9) Speakers Produce sound 2 Chapter 1 Product features
ページ9に含まれる内容の要旨
Rear components Component Function (1) SD card reader Reads data from and writes data to Secure Digital (SD) memory cards (2) USB 2.0 connector Connects external USB devices to the all-in-one (3) Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, or a headset (4) DC power connector Connects the DC-in cable from the AC power adapter (5) Ethernet connector Connects an Ethernet cable to the all-in-one (6) USB 2.0 connector Connects ext
ページ10に含まれる内容の要旨
2 Setting up the hardware You can install the all-in-one on a desktop or mount it to a mounting fixture such as a wall mount or swing arm. Be sure to place the all-in-one in a convenient, well-ventilated location. Connect the cables after you have installed the all-in-one to a mounting fixture. To set up the all-in-one, ensure that the power is turned off to the all-in-one and all attached accessories, and then follow the instructions below for your configuration. Preparing for desk use To assem
ページ11に含まれる内容の要旨
2. Lift and rotate the stand until it is positioned straight up so you can access the screw that secures the stand to the all-in-one. 3. Remove the two screws that secure the stand to the all-in-one (1), and then lift up the bottom of the stand slightly and remove it from the all-in one (2). Preparing for wall mounting 5
ページ12に含まれる内容の要旨
4. Align the screw holes on the mounting fixture with the VESA holes on the back of the all-in-one, and then insert four 10 mm screws (not provided) through the holes on the mounting fixture and into the mounting holes on the all-in-one. CAUTION: This all-in-one supports the VESA industry standard 100 mm mounting holes. To attach a third-party mounting solution to the all-in-one, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer screws must not be used because they may damage the
ページ13に含まれる内容の要旨
Connecting the cables The cable connections required depend on whether you are using a keyboard and mouse or wired (Ethernet) or wireless connection. 1. Place the all-in-one in a convenient, well-ventilated location. 2. Remove the rear I/O cover from the all-in-one. 3. If you want to use a wired network connection, connect an Ethernet cable to the Ethernet port on the all-in-one’s rear panel (1), and then to an active Ethernet jack (2). For more information, see Connecting to wired networks on p
ページ14に含まれる内容の要旨
4. If you want to use a keyboard and/or mouse, connect the keyboard and mouse to the USB ports on the all-in-one's rear panel. 8 Chapter 2 Setting up the hardware
ページ15に含まれる内容の要旨
5. Connect the DC-in cable on the back of the all-in-one (1), and then connect the power cord into the AC adapter (2) and the other end to an electrical wall outlet (3). WARNING! To reduce the risk of electric shock or damage to the equipment: - Do not disable the power cord grounding plug. The grounding plug is an important safety feature. - Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. - Disconnect power from the equipment by unpluggin
ページ16に含まれる内容の要旨
Adjusting the tilt For optimal viewing, adjust the screen tilt to your own preference. 1. Face the rear of the all-in-one and hold it so that you do not topple it while changing the tilt. 2. Without touching the screen, adjust the tilt by rotating the stand up and down. 10 Chapter 2 Setting up the hardware
ページ17に含まれる内容の要旨
Turning on the all-in-one for the first time NOTE: For a seamless experience, the Startup Wizard requires an internet connection. Before powering on the all-in-one, please be prepared to establish a wired (Ethernet) or wireless (Wi-Fi) internet connection. After connecting the cables, press the power button on the right side of the all-in-one to turn it on. CAUTION: Burn-in image damage may occur on displays that show the same static image on screen for a prolonged period of time.* To avoid burn
ページ18に含まれる内容の要旨
Using the touchscreen A touch screen device allows you to control items on the screen directly with your fingers. TIP: On touch screen devices, you can also perform on-screen actions with a keyboard and mouse. One-finger slide The one-finger slide is mostly used to pan or scroll through lists and pages, but you can use it for other interactions, too, such as moving an object. ● To scroll across the screen, lightly slide one finger across the screen in the direction you want to move. ● To drag, p
ページ19に含まれる内容の要旨
Rotating Rotating allows you to turn items such as photos. Anchor the forefinger of your left hand on the object you want to rotate. Using your right hand, slide your forefinger around in a sweeping motion from 12 o’clock to 3 o’clock. To reverse the rotation, move your forefinger from 3 o’clock to 12 o’clock. NOTE: Rotate is intended for specific apps where you can manipulate an object or image. Rotate may not be functional for all apps. Swipes With swipes you can flip between screens or images
ページ20に含まれる内容の要旨
Connecting to networks You can connect to networks with either a wired (Ethernet) or wireless (Wi-Fi) connection. You cannot enable Ethernet and Wi-Fi connections at the same time. Connecting to wireless networks The all-in-one’s wireless network capability lets you connect the all-in-one to wireless local area networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs). In a WLAN, the mobile wireless module in your all-in-one communicates with a wireless router or a wireless acce
