ページ1に含まれる内容の要旨
RGB 500 AKM
RGB 560 AKM
Architectural Series Universal Interfaces
with Audio and ADSP™
68-468-02
Printed in the USA
ページ2に含まれる内容の要旨
Precautions Safety Instructions • English Warning Power sources This equipment should be operated only from the power source indicated on the This symbol is intended to alert the user of important operating and maintenance product. This equipment is intended to be used with a main power system with a grounded (servicing) instructions in the literature provided with the equipment. (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or This symbol is inte
ページ3に含まれる内容の要旨
Table of Contents Chapter 1 • Introduction ....................................................................................................... 1-1 About the Interfaces ....................................................................................................... 1-2 Features................................................................................................................................... 1-2 RGB 500 AKM and RGB 560 AKM features........................................
ページ4に含まれる内容の要旨
Table of Contents, cont’d ii RGB 500 AKM and RGB 560 AKM Table of Contents
ページ5に含まれる内容の要旨
RGB 500 AKM and RGB 560 AKM Chapter One 1 Introduction About the Interfaces Features
ページ6に含まれる内容の要旨
H. SHIFT MIN/MAX ID PIN 11 LOCAL OUT ID PIN 4 TM RGB 558 AKM with ADSP Intr Introduction, cont’d oduction About the Interfaces Extron’s RGB 500 AKM and RGB 560 AKM interfaces are universal, analog, computer-video interfaces with 300 MHz (-3dB) video bandwidth. The interfaces feature Extron’s ADSP™ (Advanced Digital Sync Processing™) to ensure stable sync signal output, while allowing trouble-free centering control. Up to three interfaces can be installed in an Ackermann floor tank. Ackermann Fl
ページ7に含まれる内容の要旨
Serration pulse switch — This DIP switch-selectable feature adds or strips the serration pulses from the signal to make it compatible with digital display devices. Use the serration pulse switch if flagging or bending occurs at the top of the video display. Gain/peaking adjustment — Output gain and peaking levels may be adjusted individually for red, green, and blue channels by using jumpers that are accessible inside the enclosure. Sync polarity adjustment — Horizontal and vertical sync out
ページ8に含まれる内容の要旨
Introduction, cont’d 1-4 RGB 500 AKM and RGB 560 AKM Introduction
ページ9に含まれる内容の要旨
RGB 500 AKM and RGB 560 AKM Chapter Two 2 Installation and Operation Front Panel Features Installation Overview Installation and Operation Instructions
ページ10に含まれる内容の要旨
Installation and Operation, cont’d Installation and Operation Front Panel Features 2 3 4 5 6 7 AUDIO INPUT H. SHIFT HIGH Z MIN/MAX TM RGB 500 AKM with ADSP 8 1 Figure 2 — RGB 500 AKM front panel 3 6 9 2 7 4 AUDIO INPUT H. SHIFT BUFFERED MIN/MAX LOCAL OUT TM RGB 560 AKM with ADSP 10 11 1 Figure 3 — RGB 560 AKM front panel Signal output and interface power cables — Five BNC female connectors 1 for video output: red, green, blue, horizontal sync (black), and vertical sync (yellow); one 5-pole 3.5mm
ページ11に含まれる内容の要旨
5 Video input termination toggle switch (RGB 500 AKM only) — The toggle switch on the front panel allows you to select video input impedance. Set the toggle switch to the top position for high Z when a local monitor is connected, or set it to the bottom position for 75 ohm impedance when no local monitor is connected. 6 DIP switch access cover and DIP switches — Use a screwdriver to remove the cover to gain access to the DIP switches. These ON eight DIP switches, numbered 1 through 8 from left
ページ12に含まれる内容の要旨
Installation and Operation, cont’d 6 — Vertical sync pulse width For some digital display devices, if no picture appears, the picture cuts in and out, or the picture is scrambled, you may need to select the wide vertical sync pulse width. ON — When this switch is set to On, narrow sync pulse width is selected. OFF — When this switch is set to Off, wide sync pulse width is selected. (Default setting.) 7 & 8 — Composite sync routing These are used for routing local monitor signals for Macintosh 1
ページ13に含まれる内容の要旨
Installation Overview To install the interface, follow these basic steps: Set the DIP switches, located inside the access panel (see page 2-3), and the 1 gain/peaking adjustment jumpers, located inside the enclosure. (See below.) Set the front panel video termination toggle switch on the RGB 500 AKM, or 2 set the front panel ID bit DIP switches on the RGB 560 AKM. (See page 2-4.) Connect the signal output and power cables. (See “Attaching output 3 cables” on page 2-6.) 4 Temporarily connect t
ページ14に含まれる内容の要旨
Installation and Operation, cont’d AUDIO INPUT H. SHIFT BUFFERED MIN/MAX LOCAL OUT TM RGB 560 AKM with ADSP Remove (2) Remove (2) Screws Remove (2) J18 Screws Screws J17 J16 Use Needlenose Pliers to move jumpers PC Board Front Face (Inside) Figure 4 — Setting the gain/peaking jumpers 2. Locate the gain/peaking jumpers on the wider of the two circuit boards attached to the back of the faceplate (figure 4). J16 controls blue gain/peaking, J17 controls red, and J18 controls green. 3. Using needlen
ページ15に含まれる内容の要旨
Connect the sleeve to ground (GND). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits. Unbalanced Output Tip See Warning Sleeve (GND) Tip See Warning Balanced Output Tip Ring Sleeve (GND) Tip Ring Figure 5 — Wiring for audio output Power connector Attach the 3-pole, 3.5 mm captive screw power connector to a 12 to 24VDC or 12 to 24VAC, .5A (minimum), external power supply, such as Extron’s #70-055-01. The center pole contains no conductor. Connect conductors
ページ16に含まれる内容の要旨
Installation and Operation, cont’d 3. If the image appears, but it looks scrambled or cuts in and out, check the DIP switch settings. If all switches are already set to what should be the correct settings for the connected input and output devices, try different settings. If the display device is digital (including LCD, DLP, and plasma devices), try changing the vertical sync pulse width (see page 2-4). Next, try changing the sync options (sync on green, composite sync output), sync polarity, o
ページ17に含まれる内容の要旨
RGB 500 AKM and RGB 560 AKM Appendix A A Specifications
ページ18に含まれる内容の要旨
Specifications, cont’d Specifications Video Gain ................................................ Unity (0.70V p-p), (0.725V p-p) 50% peaking, (0.75V p-p) 100% peaking Bandwidth ..................................... 300 MHz (-3dB) Video input Number/signal type ................... 1 analog RGBHV, RGBS, RGsB, RsGsBs Connectors RGB 500 AKM 1 9-pin D male, MBC/LBC cable or buffer RGB 560 AKM 1 15-pin HD female Minimum/maximum levels ....... Analog ....... 0.3V to 1.5V p-p with no offset Impedan
ページ19に含まれる内容の要旨
Audio input Number/signal type ................... 1 PC level stereo, unbalanced Connectors ................................... 1 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) Impedance .................................... 10 kohms, DC coupled Maximum level ............................ +8.5dBu, (unbalanced) at stated %THD+N Audio output Number/signal type ................... 1 stereo (2 channel), balanced/unbalanced Connectors ................................... 1 3.5 mm s
ページ20に含まれる内容の要旨
Specifications, cont’d A-4 RGB 500 AKM and RGB 560 AKM Specifications
