ページ1に含まれる内容の要旨
SC-602 Amplifier
™
SubContractor Series
USER’S
MANUAL
SC-602 Amplifier, SC-600 IW,
SC-600 IF/IC Subwoofers
ページ2に含まれる内容の要旨
. www.v elodyne.com SC-602 Amplifier User’s Manual i
ページ3に含まれる内容の要旨
Table of Contents Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 – SC-602 Subwoofer Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 – SC-600 IW, SC-600 IF/IC Subwoofers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Setup Checklist . . . .
ページ4に含まれる内容の要旨
Congratulations Congratulations on your purchase of a Velodyne SubContractor (SC) Series 602 amplifier and subwoofer. This system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to ensure safe and proper system operation. Warning! To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open the speaker enclosure or the amp chassis cover. Please observe all warnings on the equipment
ページ5に含まれる内容の要旨
SC-600 IW, SC-600 IF/IC SUBWOOFERS SC-600 IW (In-Wall): - Two high excursion 6.5” active drivers, two 12.5” x 3” oval passive radiators with ribbed rubber surround - High-excursion rubber surrounds on both active and passive drivers - 2” 4 layer copper voice coils - Frequency Response: 37-120 Hz (+/- 3 dB) - 4 ohm impedance SC-600 IF/IC (In-Floor/In-Ceiling): - 12” (9.7” piston diameter) subwoofer - 2.5” 4 layer copper voice coils - Oversized spider for linearity at high excursion - High-excu
ページ6に含まれる内容の要旨
Installation FRONT PANEL CONTROLS AND DISPLAYS 602 FRONT PANEL CONTROLS AND DISPLAYS Figure 1: Front Panel Connections of the SC-602 amplifier. Following are brief descriptions of the controls described in Figure 1. More detail on these controls can be found in the next section. (1) Power Switch This button forces your SC-602 amplifier into standby mode. The power LED turns amber, f, and the amplifier puts out no power. The unit will remain in this the numeric LED shuts of mode until the POW
ページ7に含まれる内容の要旨
(6) LED Numeric Indicator This LED supplies information on volume, crossover, woofer type, and other information. The “light” button on the remote deactivates this display. Upon startup, the display shows the model of subwoofer the SC-602 amp is set to, then reverts to the volume indicator. (7) Volume Control These buttons allow you to balance the output from the subwoofer with the output of the main speakers in your system. The volume should be set to achieve similar volume level of both the
ページ8に含まれる内容の要旨
Line-Level Subwoofer Signal from Source (LFE) SC-600 SC-600 Subwoofer Subwoofer Note: A “Y” connector can be used as an option. Figure 2A: Mono (LFE) Line-Level Connection. Stereo Line-Level Output to Another System, e.g. a second SC-600 or SC-602 amplifier Stereo Line-Level Input from Source SC-600 SC-600 Subwoofer Subwoofer Figure 2B: Stereo Line-Level Connection. . www.v elodyne.com SC-602 Amplifier User’s Manual 5
ページ9に含まれる内容の要旨
(11) IR Input An IR repeater can be connected to this mini-jack. (12) 12V Trigger When this 2-conductor mini-jack is connected, the amplifier remains in power-off mode until the trigger is applied. The correct trigger is +12V on the tip of the connector relative to the grounded sleeve. (13) RS-232 In Use this port to communicate with an RS-232 controlled touch panel system. See Appendix A for an explanation of the use of the serial port, available commands and their formats. (14) Signal Sen
ページ10に含まれる内容の要旨
Speaker-Level Signal from Source 80 Hz and Above to SC-600 SC-600 Satellite Speakers Subwoofer Subwoofer Figure 3: Speaker-Level Connection. (17) and (18) Subwoofer Connection 5-way Binding Post Terminals Connect the output terminals to the subwoofer being controlled by the SC-602 amplifier. Only connect ONE subwoofer to each red/black pair of subwoofer output terminals - DO NOT connect multiple subwoofers to the terminals in any configuration. Caution!!! To avoid damage to your SC-602 amp and
ページ11に含まれる内容の要旨
Rear Panel Connections — Detailed Explanation The SC-602 amplifier is equipped with both speaker-level and line-level inputs. Use the RCA/Phono type “INPUT” jacks when connecting from a pre-amp, signal processor, or line-level crossover. The “SPEAKER LEVEL INPUT” jacks connect directly to the speaker outputs of an integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs because of their high impedance. Note: Do not use both t
ページ12に含まれる内容の要旨
In these installations, you may want to bypass the crossover in either the processor or the Velodyne SC-602 amplifier as described above. However, in some cases you may want to use BOTH crossovers. If you choose to do this you should stagger the frequencies, (i.e., 120 Hz subwoofer, 80 Hz processor) for best results. Note: If not using an external crossover, you should use the subwoofer’s built-in crossover for optimal performance. When using a single RCA sub out from the processor, it does no
ページ13に含まれる内容の要旨
Selecting the Subwoofer to be Controlled Your SC-602 amplifier can control the Velodyne SC-600 Series subwoofers as well as generic passive subwoofers. Special internal software settings are designed to maximize performance and reliability depending on the model of subwoofer being controlled, so it is important to match the SC-602 amplifier with the subwoofer it is controlling. The SC-602 amplifier comes with a default setting for the SC-600 IW subwoofer. When the unit is first powered up, th
ページ14に含まれる内容の要旨
Usage This section addresses EQ set-up and day-to-day usage of your SC-602 amplifier. Remote Control The features of the SC-602 remote control are listed below. • POWER — This button forces your SC-602 amplifier unit into standby mode. The power LED turns amber, the numeric LED shuts off, and the amplifier puts out no power. The unit will remain in this mode until the POWER button is pressed again. To fully deactivate (i.e. power down) the unit, use the main power switch on the back panel. Not
ページ15に含まれる内容の要旨
night mode feature on or off. Activation of night mode causes “n” to appear briefly on the display. When night mode is deactivated, the display shows “n off” and then returns to normal function. • VOLUME CONTROL — This control allows you to balance the output from the subwoofer with the output of the main speakers in your system. This control should be set to achieve similar volume level of both the main speakers and subwoofer. When pressing volume up or down, the volume level change is shown
ページ16に含まれる内容の要旨
The following table indicates musical style and which preset is recommended for it. MUSICAL STYLE SUGGESTED PRESET Action Adventure Movies Movies Country – Rock R&B – Rock Country – Soft Jazz – Classical Folk Jazz – Classical Indie Music R&B – Rock Pop R&B – Rock Rock R&B – Rock Alternative Rock Jazz – Classical Blues Jazz – Classical Broadway and Vocalists Jazz – Classical Children’s Music Jazz – Classical Christian and Gospel Jazz – Classical Classic Rock R&B – Rock Classical Jazz – Classica
ページ17に含まれる内容の要旨
Restoring Defaults There is a feature that allows you to restore default settings for your SC-602 amplifier. By pressing presets in EXACTLY the following order on the remote, the unit’s power light will blink indicating that you have restored defaults. Preset 1: Movies Preset 2: R&B – Rock Preset 3: Jazz – Classical Preset 4: Games Preset 4: Games Preset 3: Jazz – Classical Preset 2: R&B – Rock Preset 1: Movies When you press the presets in the above order, the numeric LED will display “P3” in
ページ18に含まれる内容の要旨
Troubleshooting and Service Before seeking service for your amplifier or subwoofer, please re-check all systems. Following is a simple troubleshooting guide to assist you. 1. Verify that the unit is plugged in and power outlet used is active. 2. Is the power switch on? 3. Is the unit receiving an input signal from your receiver or processor? 4. Have all controls on the amplifier (volume, crossover, phase, etc.) been properly set? 5. If the unit has been running at high levels, one of th
ページ19に含まれる内容の要旨
Specifications www.v elodyne.com SC-602 Amplifier User’s Manual 16
ページ20に含まれる内容の要旨
Appendix A: RS-232 Serial Overview and Commands Introduction This document outlines Velodyne’s SubContractor (SC) RS-232 protocol specification. This ® protocol indicates how SC products receive run-time commands from devices such as Creston Universal Remote Controls. Com Port Setup Use standard communications settings: Baud Rate: 9600, Data Bits: 8, Parity: None, Stop Bits: 1 SC IN and OUT Port Pin Configuration SC serial ports use a standard configuration that allows direct connection to a PC
