ページ1に含まれる内容の要旨
HDMI4X4
USER MANUAL
www.xantech.com
ページ2に含まれる内容の要旨
CONTENTS 1 Introduction / Product Features / Package Contents 2 Panel Layouts 3 Operational Instructions 4 IR Remote Control Installation 5 EDID Confi guration Guide 6 EDID Modes 7 Resolving IR confl icts 8 RS-232 Control Interface 9 Rack Mount Diagram 10 Specifi cations
ページ3に含まれる内容の要旨
INTRODUCTION The 4X4 HDMI™ Matrix routes high defi nition video in multiple resolutions up to 1080p plus multichannel digital audio from any of the four HDMI™ sources to the displays. Four outputs gives you the choice of sending high defi nition audio and video signals up to four displays. Any four sources to any four dislay devices matrix switching allows for maximum versatility for integrated systems. The 4X4 HDMI Switcher eliminates the need to disconnect and reconnect sources to a displa
ページ4に含まれる内容の要旨
FRONT PANEL LAYOUT -2-
ページ5に含まれる内容の要旨
OPERATION NOTES PLEASE READ THESE NOTES BEFORE INSTALLING OR OPERATING THE HDMI4X4 MATRIX SWITCHER • The 4X4 HDMI Matrix is housed in a metal box for better RF shielding. • The 4X4 HDMI Matrix works with all DVI and HDMI displays. • The 4X4 HDMI Matrix supports both AUDIO and VIDEO signals. • The 4X4 HDMI Matrix is fully HDCP compliant. VIDEO COMPATIBILITY NOTE An HDMI source connects to the HDMI4X4 Matrix Switcher with four input cables and four output cables. Output devices are examined to o
ページ6に含まれる内容の要旨
RMT16-IR INSTALLATION 1. Remove battery cover from the back of the RMT16-IR remote. 2. Verify that DIP switches 1 & 2 are in the down (OFF) position. 3. Insert the battery; hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT16-IR remote by pressing ONLY one button at a time. The indicator light on the remote will fl ash once each time you press a button. WARNING: Do not press multiple buttons simulta- neously and d
ページ7に含まれる内容の要旨
CUSTOM EDID CONFIGURATION VIA DIP SWITCHES Extended display identifi cation data (EDID) is a data structure provided by a display to describe its capabilities to any source that asks for it. The EDID includes manufacturer name, product type, timings supported by the display, display size, luminance data, (for digital displays only) pixel mapping data, supported audio channels and formats. This information is used by the source to cater its output to resolutions and audio formats that are sup
ページ8に含まれる内容の要旨
SETTING EDID MODES USING THE DIP SWITCH BANK: EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON) -EDID is copied from the device connected to the fi rst active HDMI output port. - All features newer than HDMI 1.2 are cleared. EDID Mode 1 (Switch 1=ON Switch2=OFF Switch5=ON) -Same as Mode 0 and adds basic audio support. EDID Mode 2 (Switch 1=OFF Switch2=ON Switch5=ON) -Same as Mode 0 and adds full audio support. EDID Mode 3 (Switch 1=ON Switch2=ON Switch5=OFF) -EDID is generated based on the
ページ9に含まれる内容の要旨
Resolving Infrared Code Confl icts In the event of IR confl icts, please do the following: 1. Remove the battery cover from the back of the RMT16-IR remote. 2. Locate the DIP Switches above the batteries. 3. Switch the DIP Switches on the RMT16-IR to any of the combina- tions pictured below. 4. DIP Switches 1 and 2 in the RMT16-IR infrared remote correspond with DIP Switches 3 and 4 inside the 4X4 HDMI Matrix respectively. Switch the DIP switches inside the 4X4 HDMI Matrix to match the same Rem
ページ10に含まれる内容の要旨
RS-232 INTERFACE ASCII Binary 1 1 0011 0001 2 2 0011 0010 3 3 0011 0011 4 4 0011 0100 5 5 0011 0101 6 6 0011 0110 7 7 0011 0111 8 8 0011 1000 9 9 0011 1001 a 10 0110 0001 b 11 0110 0010 c 12 0110 0011 d 13 0110 0100 e 14 0110 0101 f 15 0110 0110 g 16 0110 0111 RS232 Settings Bits per second 19200 Data bits 8 Parity None Stop bits 1 Flow Control None -8-
ページ11に含まれる内容の要旨
4X4 HDMI RACK MOUNT DIAGRAM -9-
ページ12に含まれる内容の要旨
SPECIFICATIONS Video Amplifi er Bandwidth 1.65 Gbps Input Video Signal 1.2 volts p-p Input DDC Signal 5 volts p-p (TTL) Single Link Range 1080p / 1920 x 1200 HDMI Input/Output Connector Type A 19-pin Female Remote Control Port RS-232 Female, Mini-Stereo Power Consumption 60 watts (max) Power Supply 24V DC Dimensions 17” W x 1.75” H x 5.875” D Shipping Weight 10 lbs. Technical Support Mailing Address Hours: 7AM-5:30 PM PST Xantech Corporation Phone: 800.843.5465 13100 Telfai
ページ13に含まれる内容の要旨
ページ14に含まれる内容の要旨
www.xantech.com
