ページ1に含まれる内容の要旨
USB2502
2-Port USB 2.0 Hub
Controller
Datasheet
PRODUCT FEATURES
Integrated USB 2.0 Compatible 2-Port Hub On-Board 24MHz Crystal Driver Circuit or 24 MHz
— High-Speed (480Mbits/s), Full-Speed (12Mbits/s) and
external clock driver
Low-Speed (1.5Mbits/s) compatible
Internal PLL for 480MHz USB 2.0 Sampling
— Full power management with ganged power control
Internal 1.8V Linear Voltage Regulator
— Detects Bus-Power/Self-Power source and changes
mode automatically Integrated USB terminat
ページ2に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet ORDER NUMBERS: USB2502-AEZG FOR 36 PIN LEAD-FREE ROHS COMPLIANT QFN PACKAGE; USB2502-HT FOR 48 PIN LEAD- FREE ROHS COMPLIANT TQFP PACKAGE 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for constructi
ページ3に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table of Contents Chapter 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 OEM Selectable Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 2 Pin Table 2-Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 3 Pin Configuration 2-Port Hu
ページ4に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet List of Tables Table 2.1 2-Port Pin Table for 36-QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 2.2 2-Port Pin Table for 48-TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table 4.1 2-Port Hub Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 4.2 SMBus or EE
ページ5に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet List of Figures Figure 3.1 2-Port 36-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3.2 2-Port 48-Pin TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 4.1 2-Port Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 5
ページ6に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Chapter 1 General Description The SMSC 2-Port Hub is fully compliant with the USB 2.0 Specification and will attach to a USB host as a Full-Speed Hub or as a Full-/High-Speed Hub. The 2-Port Hub supports Low-Speed, Full-Speed, and High-Speed (if operating as a High-Speed Hub) downstream devices on all of the enabled downstream ports. The Hub works with an external USB power distribution switch device to control V switching to BUS downstream ports, and to l
ページ7に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Chapter 2 Pin Table 2-Port Table 2.1 2-Port Pin Table for 36-QFN UPSTREAM USB 2.0 INTERFACE (3 PINS) USBDP0 USBDN0 VBUS_DET 2-PORT USB 2.0 INTERFACE (10 PINS) USBDP1 USBDN1 USBDP2 USBDN2 GR1/ GR2/ PRTPWR_POL RBIAS NON_REM0 NON_REM1 PRTPWR OCS_N SERIAL PORT INTERFACE (3 PINS) SDA/SMBDATA SCL/SMBCLK/ CFG_SEL1 CFG_SEL0 MISC (7 PINS) XTAL1/CLKIN XTAL2 RESET_N SELF_PWR ATEST/ CLKIN_EN TEST REG_EN POWER, GROUND (13 PINS) SMSC USB2502 7 Revision 2.3 (08-27-07) D
ページ8に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 2.2 2-Port Pin Table for 48-TQFP UPSTREAM USB 2.0 INTERFACE (3 PINS) USBDP0 USBDN0 VBUS_DET 2-PORT USB 2.0 INTERFACE (10 PINS) USBDP1 USBDN1 USBDP2 USBDN2 GR1/ GR2/ PRTPWR_POL RBIAS NON_REM0 NON_REM1 PRTPWR OCS_N SERIAL PORT INTERFACE (3 PINS) SDA/SMBDATA SCL/SMBCLK CFG_SEL1 CFG_SEL0 MISC (7 PINS) XTAL1/CLKIN XTAL2 RESET_N SELF_PWR ATEST/ CLKIN_EN TEST REG_EN POWER, GROUND AND NO CONNECT (25 PINS) Revision 2.3 (08-27-07) 8 SMSC USB2502 DATASHEET
ページ9に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Chapter 3 Pin Configuration 2-Port Hub VDD33CR 28 18 VDD18 VSS 29 17 VSS XTAL2 30 16 SELF_PWR XTAL1/CLKIN 31 15 OCS_N SMSC VDDA18PLL 32 14 PRTPWR USB2502 VDDA33PLL 33 (Top View QFN-36) 13 PRTPWR_POL ATEST/REG_EN 34 12 GR2/NON_REM1 Thermal Slug RBIAS 35 11 GR1/NON_REM0 (must be connected to VSS) VSS 36 10 VSS Indicates pins on the bottom of the device. Figure 3.1 2-Port 36-Pin QFN SMSC USB2502 9 Revision 2.3 (08-27-07) DATASHEET VDDA33 1 27 VDD18 USBDP0 2 2
ページ10に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Figure 3.2 2-Port 48-Pin TQFP Revision 2.3 (08-27-07) 10 SMSC USB2502 DATASHEET
ページ11に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Chapter 4 2-Port Hub Block Diagram Upstream 24 MHz To EEPROM or V USB Data Crystal SMBus Master BUS SD SCK 3.3V 1.8V PLL Serial Interface Bus-Power Upstream 1.8V Reg PHY SIE Controller Repeater Port Transaction Translator Controller Routing Logic OC Sense Switch Driver Downstream PHY #1 Downstream PHY #2 LED Driver Strapping Options Downstream OC Switch/LED Downstream USB Data Sense Driver/optís USB Data Figure 4.1 2-Port Block Diagram Table 4.1 2-Port H
ページ12に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 4.1 2-Port Hub Pin Descriptions (continued) NAME SYMBOL TYPE FUNCTION 2-PORT USB 2.0 HUB INTERFACE High-Speed USB USBDN[2:1] IO-U These pins connect to the downstream USB peripheral devices attached to the Hub’s ports. Data USBDP[2:1] USB Power PRTPWR O8 Enables power to USB peripheral devices (downstream). Enable The active signal level of the PRTPWR pin is determined by the Power Polarity Strapping function of the PRTPWR_POL pin. Port [2:1] Gr
ページ13に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 4.1 2-Port Hub Pin Descriptions (continued) NAME SYMBOL TYPE FUNCTION SERIAL PORT INTERFACE Serial Data/SMB SDA/SMBDATA IOSD12 (Serial Data)/(SMB Data) signal. Data Serial Clock/SMB SCL/SMBCLK/ IOSD12 (Serial Clock)/(SMB Clock) signal. This multifunction pin is read on the rising edge of RESET_N (see the applicable Clock CFG_SEL0 RESET_N timing table in Section 5.6.1) and will determine & the hub configuration method as described in Table 4.2. Co
ページ14に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 4.3 Miscellaneous Pins (continued) NAME SYMBOL TYPE FUNCTION Analog Test ATEST/ AIO This signal is used for testing the analog section of the chip, and to enable or disable the internal 1.8v regulator. & REG_EN Internal 1.8V This pin must be connected to VDDA33 to enable the voltage internal 1.8V regulator, or to VSS to disable the internal regulator regulator. enable When the internal regulator is enabled, the 1.8V power pins must be left u
ページ15に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 4.5 Buffer Type Descriptions (continued) BUFFER DESCRIPTION IOSD12 Open drain….12mA sink with Schmitt trigger, and must meet I2C-Bus Specification Version 2.1 requirements. ICLKx XTAL Clock Input OCLKx XTAL Clock Output I-R RBIAS IO-U Defined in USB Specification. Note: Meets USB 1.1 requirements when operating as a 1.1-compliant device and meets USB 2.0 requirements when operating as a 2.0-compliant device. AIO Analog Input/output. Per PHY test r
ページ16に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Chapter 5 Functional Block Description 5.1 2-Port Hub SMSC’s USB 2.0 2-Port Hub is fully specification compliant to the Universal Serial Bus Specification Revision 2.0 April 27,2000 (12/7/2000 and 5/28/2002 Errata). Please reference Chapter 11 (Hub Specification) for general details regarding Hub operation and functionality. For performance reasons, the 2-Port Hub provides 1 Transaction Translator (TT) per port (defined as Multi-TT configuration), divided
ページ17に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet 5.1.1.5 High-Speed Disable Allows an OEM to force the Hub to configure as a Full-Speed device only (i.e. High-Speed not available). This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.6 EOP Disable During FS operation only, this permits the Hub to send EOP if no downstream traffic is detected at EOF1. See Section 11.3.1 of the USB 2.0 Specification for additional details. This field is set by the OEM using either the SMBu
ページ18に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet When Dynamic Power switching is enabled, the Hub detects the availability of a local power source by monitoring the external SELF_PWR pin. If the Hub detects a change in power source availability, the Hub immediately disconnects and removes power from all downstream devices and disconnects the upstream port. The Hub will then re-attach to the upstream port as either a Bus-Powered Hub (if local-power in unavailable) or a Self-Powered Hub (if local power is
ページ19に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet 5.2 EEPROM Interface The SMSC Hub can be configured via a 2-wire (I2C) EEPROM. (Please see Table 4.1, "7-Port Hub Pin Descriptions" for specific details on how to enable the I2C EEPROM option). The Internal state-machine will, (when configured for EEPROM support) read the external EEPROM for configuration data. The hub will then “attach” to the upstream USB host. Please see Table 5.1 User-Defined Descriptor Data for a list of data fields available. 5.2.1
ページ20に含まれる内容の要旨
2-Port USB 2.0 Hub Controller Datasheet Table 5.1 User-Defined Descriptor Data (continued) DEFAULT DEFAULT BYTE CFG CFG MSB: SIZE SELF BUS FIELD LSB (BYTES) (HEX) (HEX) DESCRIPTION Config Data 6 1 88 0C Configuration data byte #1 for Hub options. Byte 1 Config Data 7 1 90 90 Configuration data byte #2 for Hub options. Byte 2 8 1 00 00 Defines the ports that contain attached Non Removable devices (this is used only when Hub is part of Device a compound device). Port Disable 9 1 00 00 Selects
