Pelco CM9700UTP32Aの取扱説明書

デバイスPelco CM9700UTP32Aの取扱説明書

デバイス: Pelco CM9700UTP32A
カテゴリ: スイッチ
メーカー: Pelco
サイズ: 1.34 MB
追加した日付: 4/3/2013
ページ数: 24
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスPelco CM9700UTP32Aの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Pelco CM9700UTP32Aに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Pelco CM9700UTP32Aをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Pelco CM9700UTP32Aのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Pelco CM9700UTP32Aの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Pelco CM9700UTP32A 取扱説明書 - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Pelco CM9700UTP32Aを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Pelco CM9700UTP32Aの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

INSTALLATION
CM9700UTP Series
Multichannel
Active Receivers
16 or 32 Channels
C3646M-C (6/09)

ページ2に含まれる内容の要旨

ページ3に含まれる内容の要旨

Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description. . . . . . . . . . . . . . . . . . . . . .

ページ4に含まれる内容の要旨

List of Illustrations 1 CM9700UTP16A Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 CM9700UTP32A Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 CM9700UTP16A Back Panel. . . . . . . . . . . . . . . . . . . . . .

ページ5に含まれる内容の要旨

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the pola

ページ6に含まれる内容の要旨

Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provid

ページ7に含まれる内容の要旨

Description The CM9700UTP Series multichannel active receiver is a 16- or 32-channel unit that can receive live video over unshielded twisted pair (UTP) cable. The front panel of each model contains a dial and a LED per channel; dials are used for selecting cable distance. The back panel of each model features BNC connectors for video output, RJ-45 video input connectors, and video ribbon cable to connect to a CM9700 Series matrix. Models CM9700UTP16A 16-channel active receiver; 16 BNC conne

ページ8に含まれる内容の要旨

FRONT PANEL Figure 1. CM9700UTP16A Front Panel 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 1 2 3 MADE IN USA Figure 2. CM9700UTP32A Front Panel ì Pelco Badge: Glows blue when the unit has power. When the temperature rises above the specified temperature (95°F [35°C]), or when any of the fans fail, the Pelco badge LED will blink and a buzzer will sound indicating there is an alarm condition. î Distance Rotary Switch: The manual selection of the gain for

ページ9に含まれる内容の要旨

BACK PANEL Figure 3. CM9700UTP16A Back Panel 1-4 5-8 9-12 13-16 1 17 2 18 3 19 4 20 5 21 6 22 7 23 8 24 9 25 10 26 11 27 12 28 13 29 14 30 15 31 16 32 TO MXB 17-20 21-24 25-28 29-32 100-240 VAC 50-60Hz 75A Figure 4. CM9700UTP32A Back Panel ì AC Power Connector: Connects the UTP receiver to the mains power supply (100 to 240 VAC, 50 to 60 Hz, autoranging). î BNC Connectors: There are 16 or 32 coaxial video outputs (depending on model) for each unit. BNC connectors on both models are numbered r

ページ10に含まれる内容の要旨

Installation RACK MOUNTING Install the CM9700UTP Series active receiver in a standard 19-inch (48.26 cm) equipment rack using standard mounting hardware (10-32 cage nuts and 10-32 x 0.50-inch Phillips pan head screws, supplied). The receiver is one rack unit (1 RU) high. DESKTOP MOUNTING Install the CM9700UTP Series active receiver on a desktop using the four 8-32 x 0.25-inch Phillips pan head screws (supplied) to attach the protective bumpers to the bottom of the unit. POWER AND VIDEO CONNEC

ページ11に含まれる内容の要旨

You can connect the active receiver to a transmitter such as the TW4001P passive transceiver, TW3001AT active transmitter, and CC3710/ CC3610 UTP cameras. The receiver also has video ribbon cable connectors for connecting to a CM9700 Series matrix. Connect these products using UTP Cat5e and Cat6 cable for best video performance. Table B shows the maximum cable distance for video when connecting an active receiver to a TW4001P passive transceiver. Table B. Cable Distance with TW4001P Cable Maxi

ページ12に含まれる内容の要旨

INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP16A) WARNING: To meet CE compliance standards, jumpers must be installed on channels 1 through 16. 1. Unplug the unit to turn off the power. 2. Unscrew the six, black 4-40 x 0.25-inch Phillips flat head screws that secure the cover to the chassis. 3. Remove the cover. 4. Install the 16 jumpers on the pins; use one for each channel (refer to Figure 7). The pins are labeled J66 through J81. Figure 7. Installing the Jumpers for CE Compliance

ページ13に含まれる内容の要旨

COLOR VIDEO RANGE SETTINGS For optimal tuning, adjust the rotary switch located on the front panel to the correct color video range position. Refer to Figure 8 and Table D, and then complete the following steps: 1. Plug the power cord into a power source to turn on the unit. The LED for the camera input on the front panel turns green if the channel is set to the correct color video range. If the color video range is incorrect, the LED turns orange or red. NOTE: The color burst signal-to-noise

ページ14に含まれる内容の要旨

BLACK-WHITE OR DAY/NIGHT VIDEO SETTINGS For the best picture quality, adjust the DIP switch settings. Refer to Figure 9 and Table E, and then complete the following steps: 1. Plug the power cord into a power source to turn on the unit. When the input video signal is present, the LED on the front panel glows orange. If the video range is incorrect, the LED glows red. NOTE: The color burst signal-to-noise ratio is very low for cable lengths around 4,000 ft (1219 m) and longer, depending on the ty

ページ15に含まれる内容の要旨

Configuration This section describes an optional advanced tuning procedure for troubleshooting a video path. For most installations, the steps detailed in Color Video Range Settings on page 13 should be sufficient to set up the unit. Required Equipment � Video signal generator � Oscilloscope NOTE: A signal generator and oscilloscope are preferred to perform this procedure, but a video signal from a camera observed on an oscilloscope can also be used for this process. ADVANCE COLOR VIDEO SIGNAL

ページ16に含まれる内容の要旨

ADVANCE BLACK-WHITE VIDEO SIGNAL SETTINGS (DAY/NIGHT CAMERAS) Using a video signal generator, complete the following steps to fine tune the black and white signal: 1. Verify the color video signal (refer to Advance Color Video Signal Settings on page 15). 2. Send a black-white video signal, from a signal generator or a black-white camera, through the UTP to the unit. 3. Set the rotary switch to the correct position for the cable length (refer to Table D on page 13). If the cable length is not k

ページ17に含まれる内容の要旨

Maintenance For proper ventilation, use the following instructions to maintain the fan filter and fan. For information about the operating temperature range, refer to Specifications on page 20. FAN FILTER: CLEANING OR REPLACING Filters can be cleaned and reused, or they can be replaced. The fan filter should be removed and cleaned as required to ensure proper ventilation and cooling of the unit. A clogged fan filter or an ambient operating temperature exceeding 95°F (35°C) will cause the unit’

ページ18に含まれる内容の要旨

FAN REPLACEMENT Fans maintain the unit’s internal temperature within the specified range if the ambient operating temperature is at or below 95°F (35°C). Fans are removable and field replaceable. If a fan fails, the Pelco badge LED will flash, an alarm will sound, and the fan’s indicator will glow red indicating an alarm condition. If this occurs, replace the fan next to the alarm indicator. Figure 15. Fan Replacement (32-channel model shown) ì 4-40 x 0.25-inch, Phillip flat head screws, blac

ページ19に含まれる内容の要旨

To replace a fan, refer to Figure 15 and perform the following steps: 1. Unplug the unit to turn the power off. 2. Loosen the four thumb screws located on the front panel cover (refer to Figure 16). Pull the front panel away from the chassis, and then let it hang from the front panel brackets. Figure 16. Remove Front Panel (32-channel model shown) 3. Unscrew the two, black 4-40 x 0.25-inch Phillips flat head screws that secure the front panel to the front panel bracket. 4. Unscrew the two, bla

ページ20に含まれる内容の要旨

Specifications VIDEO Video Standards NTSC/PAL/EIA/CCIR composite Video Output CM9700UTP16A 16 BNC and 1 ribbon cable connector CM9700UTP32A 32 BNC and 2 ribbon cable connectors Frequency Response 50 Hz to 6 MHz Common Mode/Differential Mode Rejection >60 dB Video Output 1.2 Vp-p ELECTRICAL Input Voltage 100 to 240 VAC, 50 to 60 Hz, autoranging Input Current CM9700UTP16A 0.38 A CM9700UTP32A 0.75 A Wire Type UTP (24 AWG minimum) Wire Category Cat5, Cat5e, or Cat6 Wire Distance Cat5 3,000 ft (914 m


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Pelco DX2000 取扱説明書 スイッチ 1
2 Pelco 100BASE-FX 取扱説明書 スイッチ 2
3 Pelco C1510M-QS 取扱説明書 スイッチ 0
4 Pelco C1501M 取扱説明書 スイッチ 0
5 Pelco C1503M 取扱説明書 スイッチ 0
6 Pelco C1906/PP 取扱説明書 スイッチ 0
7 Pelco C1566M-C 取扱説明書 スイッチ 0
8 Pelco C1528M-F 取扱説明書 スイッチ 1
9 Pelco C1555M-F 取扱説明書 スイッチ 1
10 Pelco C19125 取扱説明書 スイッチ 0
11 Pelco C1925 取扱説明書 スイッチ 0
12 Pelco 100BASE-TX 取扱説明書 スイッチ 0
13 Pelco C1925/PP 取扱説明書 スイッチ 0
14 Pelco C2403M-C 取扱説明書 スイッチ 0
15 Pelco C2491M-B 取扱説明書 スイッチ 0
16 Sony 4-296-436-11 (2) 取扱説明書 スイッチ 0
17 3Com 10/100BASE-TX 取扱説明書 スイッチ 61
18 3Com 2226-SFP 取扱説明書 スイッチ 688
19 3Com 16985ua.bk 取扱説明書 スイッチ 10
20 3Com 10BASE-T 取扱説明書 スイッチ 4