ページ1に含まれる内容の要旨
Part No. 312755-G Rev 00
May 2006
4655 Great America Parkway
Santa Clara, CA 95054
Installing the Breaker Interface
Panel for the Ethernet Routing
Switch 8010co Chassis
ページ2に含まれる内容の要旨
2 Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel. Trademarks *Nortel, the N
ページ3に含まれる内容の要旨
3 Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (8000 Series chassis) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. CE marking statement (Europe only) EN 55 022 statements This is to certify that the Nortel 8000 Series chassis and components installed within the chassis are shielded against t
ページ4に含まれる内容の要旨
4 Denan statement (Japan/Nippon only) National safety statements of compliance CE marking statement (Europe only) EN 60 950 statement This is to certify that the Nortel 8000 Series chassis and components installed within the chassis are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance. Some components installed within the 8000 Series chassis may u
ページ5に含まれる内容の要旨
5 reverse engineer or otherwise translate the Software; c) create derivative works or modifications unless expressly authorized; or d) sublicense, rent or lease the Software. Licensors of intellectual property to Nortel are beneficiaries of this provision. Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel or certify its destruction. Nortel may audit by remote polling or ot
ページ6に含まれる内容の要旨
6 312755-G Rev 00
ページ7に含まれる内容の要旨
7 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Text conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 How to get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ8に含まれる内容の要旨
8 Contents Mounting hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 DC input electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Installing the breaker interface panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Installing the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Connecting cables to th
ページ9に含まれる内容の要旨
Contents 9 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Installing the Breaker Interface Panel for the Ethernet Routing Switch 8010co Chassis
ページ10に含まれる内容の要旨
10 Contents 312755-G Rev 00
ページ11に含まれる内容の要旨
11 Figures Figure 1 Breaker interface panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 2 Front panel components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3 Shelf circuit breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 4 Alarm module display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 5 Back panel components . . . .
ページ12に含まれる内容の要旨
12 Figures Figure 30 Labeling cables for the BIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Figure 31 Rack grounding strip example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Figure 32 Attaching power supply cable leads to the BIP . . . . . . . . . . . . . . . . . . . . . 49 Figure 33 Upper and lower shelf power cables connected to the BIP . . . . . . . . . . . 50 Figure 34 Attaching the BIP ground cable . . . . . . . . . . . . . . . .
ページ13に含まれる内容の要旨
13 Tables Table 1 Alarm module display LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 2 DC power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 3 Single chassis and dual chassis input options . . . . . . . . . . . . . . . . . . . . . 53 Table 4 BIP LEDs and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Table 5 Corrective actions . . . . . . . . . . . . . . . . . .
ページ14に含まれる内容の要旨
14 Tables 312755-G Rev 00
ページ15に含まれる内容の要旨
15 Preface The breaker interface panel (BIP) provides power distribution and alarm status indications for one or two 8010co chassis in an equipment rack. The status indications can be linked to other BIPs to provide total system status to the central office (CO). This guide describes how to install the breaker interface panel in an equipment rack, connect cables, and interpret LEDs. It also includes technical specifications for the breaker interface panel. For a list of related publications
ページ16に含まれる内容の要旨
16 Preface Text conventions This guide uses the following text conventions: bold Courier text Indicates command names and options and text that you need to enter. Example: Use the dinfo command. Example: Enter show ip {alerts|routes}. italic text Indicates new terms, book titles, and variables in command syntax descriptions. Where a variable is two or more words, the words are connected by an underscore. Example: If the command syntax is show at , valid_route is one variable an
ページ17に含まれる内容の要旨
Preface 17 � sign up for automatic notification of new software and documentation for Nortel equipment � open and manage technical support cases Getting Help over the phone from a Nortel Solutions Center If you don’t find the information you require on the Nortel Technical Support Web site, and have a Nortel support contract, you can also get help over the phone from a Nortel Solutions Center. In North America, call 1-800-4NORTEL (1-800-466-7835). Outside North America, go to the following We
ページ18に含まれる内容の要旨
18 Preface 312755-G Rev 00
ページ19に含まれる内容の要旨
19 Chapter 1 Overview This chapter provides an overview of the BIP and covers the following topics: � Physical description � “Accessing the alarm module” on page 30 � “Configuration example” on page 32 Physical description The BIP provides a central rack location where redundant input DC power feeds are connected and routed to one or two 8010co chassis. The BIP also provides an alarm module and display panel that monitors system components, generates alarms, and controls LED status indicators
ページ20に含まれる内容の要旨
20 Chapter 1 Overview Front panel Figure 2 shows the BIP front panel components. Figure 2 Front panel components 1 2 3 POWER CRITICAL MAJOR Alarm Module MINOR Upper Shelf Lower Shelf 123 123 1 = Shelf circuit breakers (upper/lower shelves) 2 = Alarm module display panel 3 = Front-panel locking screws (x2) 10376EB Shelf circuit breakers (upper and lower shelves) Two groups of three circuit breakers provide input power to the power supplies for the upper and lower shelf 8010co chassis (Figure
