ページ1に含まれる内容の要旨
Upgrade Instructions for
the BayStack 100-series
Version D Boot Firmware
4401 Great America Parkway
Santa Clara, CA 95054
8 Federal Street
Billerica, MA 01821
Part No. 893-00978-A
November 1996
*893-00978-A*
ページ2に含まれる内容の要旨
4401 Great America Parkway 8 Federal Street Santa Clara, CA 95054 Billerica, MA 01821 © 1996 by Bay Networks, Inc. All rights reserved. Trademarks Bay Networks, BayStack, and SmartSwap are trademarks of Bay Networks, Inc. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Bay Networks, Inc. reserves the right to make changes to
ページ3に含まれる内容の要旨
Introduction This document outlines the procedure for upgrading the boot firmware for the Bay ™ ™ Networks BayStack 100-series network management module (NMM). If you are using the version 1.5 agent for the BayStack 100-series NMM, revision D boot firmware is necessary to enable the following feature upgrades: • Configuration menu passwords This feature allows you to designate read-only and read-write passwords for access to the NMM configuration menus through the communi
ページ4に含まれる内容の要旨
Upgrade Instructions for the BayStack 100-series Version D Boot Firmware Package Contents The BayStack 100-series NMM Version D Boot Firmware upgrade kit contains the following components: • A boot PROM for the type of NMM you have: – Bay Networks part number CG1011003 for Basic NMMs – Bay Networks part number CG1011005 for Advanced and SA NMMs • One copy of this guide, Upgrade Instructions for the BayStack 100-series Version D Boot Firmware (Bay Networks part number 893-0
ページ5に含まれる内容の要旨
Ethernet SA NMM 5. Using a #1 Phillips screwdriver, remove the screws from the NMM faceplate in the hub expansion slot. 6. Rotate the extractor lever to its unlocked position (see Figure 1). 5982.1 Figure 1. Disengaging the NMM from the hub 7. Slide the NMM out of the expansion slot. Accessing the NMM Baseboard If you have an SA or upgraded Advanced NMM, you must remove the data collection module (DCM) before you can replace the boot PROM. To remove the DCM, follow these step
ページ6に含まれる内容の要旨
Upgrade Instructions for the BayStack 100-series Version D Boot Firmware 2. Gently disengage the DCM connector from the NMM connector and lift the DCM off of the NMM. Set the DCM aside. Be sure to keep the screws with the DCM so that you can use them again later. Removing and Replacing the PROM Caution: The NMM baseboard contains devices that are sensitive to electrostatic discharge (ESD). Be sure to discharge any accumulated static electricity and to follow ESD handling proc
ページ7に含まれる内容の要旨
2. Remove the PROM. a. Use an industry-standard IC extraction tool to firmly clamp the sides of the PROM. Caution: Be careful that the extraction tool you use does not bend or put pressure on the chips adjacent to the PROM socket. b. With the extraction tool in place, pull straight up on the PROM until it disengages from its socket. Note: Do not force the PROM out of its socket. If the PROM is difficult to remove, gently wiggle the PROM back and forth a few times t
ページ8に含まれる内容の要旨
Upgrade Instructions for the BayStack 100-series Version D Boot Firmware Replacing an NMM in a BayStack Hub To replace an NMM in a BayStack 100-series NMM, follow these steps: 1. Align the left edge of the NMM metal frame with the card guides on the left side of the expansion slot (see Figure 4). 5982 Figure 4. Installing the NMM into the expansion slot 2. Slide the NMM into the hub until you feel it engage the connector inside the hub. Push the center of the NMM front panel w
