ページ1に含まれる内容の要旨
Moxa ToughNet Switch
TN-5308 Series
Layer 2 M12 unmanaged Ethernet switches
Hardware Installation Guide
First Edition, May 2009
© 2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802053080010
ページ2に含まれる内容の要旨
Overview The ToughNet TN-5308 series M12 unmanaged Ethernet switches are designed for industrial applications in harsh environments. The TN series switches use M12 connectors to ensure tight, robust connections, and guarantee reliable operation against environmental disturbances, such as vibration and shock. The TN-5308 series Ethernet switches provide 8 Fast Ethernet M12 ports, support IEEE 802.3/802.3u/802/3x with 10/100M, full/half-duplex, MDI/MDI-X auto-sensing, and provide an economi
ページ3に含まれる内容の要旨
TN-5308-LV Panel Layouts Front Panel View Rear Panel View 1 2 3 11 4 4 5 6 9 10 7 7 8 4 44 4 1. TP port’s 10/100 Mbps LED 2. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D coding) 3. Port label 4. Screw holes for panel mounting kit or DIN rail mounting kit (there are 3 holes: top middle, bottom left, and bottom right) 5. Power input LED 6. Power input port (male 5-pin shielded M12 connector with A coding) 7. Grounding screw 8. Power input port pin assignment 9
ページ4に含まれる内容の要旨
TN-5308-MV Panel Layouts Front Panel View Rear Panel View 1 2 3 11 4 4 5 6 9 7 7 10 8 4 44 4 1. TP port’s 10/100 Mbps LED 2. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D coding) 3. Port label 4. Screw holes for panel mounting kit or DIN rail mounting kit (there are 3 holes: top middle, bottom left, and bottom right) 5. Power input LED 6. Power input port (male 5-pin shielded M23 connector with A coding) 7. Grounding screw 8. Power input port pin assignment 9
ページ5に含まれる内容の要旨
Mounting Dimensions (unit = mm) TN-5308-LV Rear View Front View Side View DIN-Rail Mounting Kit TN-5308-MV Rear View Front View Side View DIN-Rail Mounting Kit — 4 —
ページ6に含まれる内容の要旨
Panel/Wall Mounting Mounting the TN-5308-LV/MV on the wall requires 3 screws. Please use the 3 screws packed in the panel mounting kit. STEP 1: Prepare the 3 screw holes on the wall according to the positions of the 3 screw holes on the switch shown on the mounting dimension diagram. STEP 2: Use one screw to go through the top-middle screw hole on the switch and screw it into the wall. STEP 3: Screw in the remaining 2 screws through the bottom-left and bottom-right holes on the switch to
ページ7に含まれる内容の要旨
Wiring Requirements WARNING Turn the power off before disconnecting modules or wires. The correct power supply voltage is listed on the product label. Check the voltage of your power source to make sure you are using the correct voltage. Do NOT use a voltage greater than what is specified on the product label. These devices must be supplied by a SELV source as defined in the Low Voltage Directive 2006/95/EC and 2004/108/EC. ATTENTION Safety First! Be sure to disconnect the power
ページ8に含まれる内容の要旨
ATTENTION This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Connecting the Power Supply The M12/M23 A-coded 5-pin male connector on the TN-5308-LV/MV front panel is used for the DC power input. You have to prepare a power cord with M12/M23 A-coded 5-pin female connector to connect the switch to the DC power input. Pinouts for the power input port on the TN-5308-LV N.C. : Not connected Pinouts for the power input port on the TN-5308-M
ページ9に含まれる内容の要旨
Connecting the Data Lines 10/100BaseT(X) Ethernet Port Connection All TN-5308 models have 8 10/100BaseT(X) Ethernet ports (4-pin shielded M12 connectors with D coding). The 10/100TX ports located on the TN-5308’s front panel are used to connect to Ethernet-enabled devices. Most users configure these ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are adjusted automatically depending on the type of Ethernet cable used (straight-through or cross-over), and the type of device
ページ10に含まれる内容の要旨
M12 (4-pin, M) to M12 (4-pin, M) Straight-Trough Cable Wiring Straight-through Cable Wiring Tx+ 1 1 Rx+ Rx+ 2 2 Tx+ Tx- 3 3 Rx- Rx- 4 4 Tx- M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring Cross-Over Cable Wiring Tx+ 1 1 Tx+ Rx+ 2 2 Tx- Tx- 3 3 Rx+ Rx- 4 6 Rx- M12 (4-pin, M) to RJ45 (8-pin) Straight-Trough Cable Wiring Straight-through Cable Wiring Tx+ 1 1 Rx+ Rx+ 2 2 Rx- Tx- 3 3 Tx+ Rx- 4 6 Tx- Auto MDI/MDI-X Connection The Auto MDI/MDI-X function allows
ページ11に含まれる内容の要旨
Dual Speed Functionality & Switching The TN-5308’s 10/100 Mbps switched M12 ports auto negotiate with the connected device to use the fastest data transmission rate supported by both devices. All of Moxa’s ToughNet switches are plug-and-play devices, so that software configuration is not required. The half/full duplex mode for the switched M12 ports is user dependent and changes (by auto-negotiation) to full or half duplex, depending on which transmission speed is supported by the attache
ページ12に含まれる内容の要旨
Auto-Negotiation and Speed Sensing All of the TN-5308’s Ethernet ports independently support auto-negotiation for speeds in the 10BaseT and 100BaseTX modes, with operation according to the IEEE 802.3u standard. This means that some nodes could be operating at 10 Mbps, while at the same time, other nodes are operating at 100 Mbps. Auto-negotiation takes place when an M12 cable connection is made, and then each time a LINK is enabled. The TN-5308 advertises its capability for using either 1
ページ13に含まれる内容の要旨
Weight TN-5308-LV: 485 g TN-5308-MV: 685 g Installation Panel mounting, DIN-Rail mounting (with optional kit) Environmental Limits Operating Temperature Standard Models: 0 to 60°C (32 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature -40 to 85°C (-40 to 185°F) Operating Humidity 5 to 95% (non-condensing) Regulatory Approvals Safety UL508 (Pending) Rail Traffic EN50155 (Environmental, Pending), EN50121-3-2 (Pending), EN50121-4 (Pending) Traffic Control NE
