ページ1に含まれる内容の要旨
General-Purpose AC Servo
J2-Super Series
General-Purpose Interface
MR-J2S- A
Servo Amplifier
Instruction Manual
B
ページ2に含まれる内容の要旨
Safety Instructions (Always read these instructions before using the equipment.) Do not attempt to install, operate, maintain or inspect the servo amplifier and servo motor until you have read through this Instruction Manual, Installation guide, Servo motor Instruction Manual and appended documents carefully and can use the equipment correctly. Do not use the servo amplifier and servo motor until you have a full knowledge of the equipment, safety information and instructions. In this Instructi
ページ3に含まれる内容の要旨
1. To prevent electric shock, note the following: WARNING Before wiring or inspection, switch power off and wait for more than 10 minutes. Then, confirm the voltage is safe with voltage tester. Otherwise, you may get an electric shock. Connect the servo amplifier and servo motor to ground. Any person who is involved in wiring and inspection should be fully competent to do the work. Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get
ページ4に含まれる内容の要旨
4. Additional instructions The following instructions should also be fully noted. Incorrect handling may cause a fault, injury, electric shock, etc. (1) Transportation and installation CAUTION Transport the products correctly according to their weights. Stacking in excess of the specified number of products is not allowed. Do not carry the motor by the cables, shaft or encoder. Do not hold the front cover to transport the controller. The controller may drop. Install the servo amplifier in a loa
ページ5に含まれる内容の要旨
CAUTION Securely attach the servo motor to the machine. If attach insecurely, the servo motor may come off during operation. The servo motor with reduction gear must be installed in the specified direction to prevent oil leakage. For safety of personnel, always cover rotating and moving parts. Never hit the servo motor or shaft, especially when coupling the servo motor to the machine. The encoder may become faulty. Do not subject the servo motor shaft to more than the permissible load. Otherwis
ページ6に含まれる内容の要旨
(4) Usage CAUTION Provide an external emergency stop circuit to ensure that operation can be stopped and power switched off immediately. Any person who is involved in disassembly and repair should be fully competent to do the work. Before resetting an alarm, make sure that the run signal is off to prevent an accident. A sudden restart is made if an alarm is reset with the run signal on. Do not modify the equipment. Use a noise filter, etc. to minimize the influence of electromagnetic interferen
ページ7に含まれる内容の要旨
(6) Maintenance, inspection and parts replacement CAUTION With age, the electrolytic capacitor will deteriorate. To prevent a secondary accident due to a fault, it is recommended to replace the electrolytic capacitor every 10 years when used in general environment. Please consult our sales representative. (7) Disposal CAUTION Dispose of the product as general industrial waste. (8) General instruction To illustrate details, the equipment in the diagrams of this Instruction Manual may have been
ページ8に含まれる内容の要旨
COMPLIANCE WITH EC DIRECTIVES 1. WHAT ARE EC DIRECTIVES? The EC directives were issued to standardize the regulations of the EU countries and ensure smooth distribution of safety-guaranteed products. In the EU countries, the machinery directive (effective in January, 1995), EMC directive (effective in January, 1996) and low voltage directive (effective in January, 1997) of the EC directives require that products to be sold should meet their fundamental safety requirements and carry the CE marks
ページ9に含まれる内容の要旨
(4) Power supply (a) Operate the servo amplifier to meet the requirements of the overvoltage category II set forth in IEC664. For this purpose, a reinforced insulating transformer conforming to the IEC or EN Standard should be used in the power input section. (b) When supplying interface power from external, use a 24VDC power supply which has been insulation-reinforced in I/O. (5) Grounding (a) To prevent an electric shock, always connect the protective earth (PE) terminals (marked ) of the ser
ページ10に含まれる内容の要旨
(7) Auxiliary equipment and options (a) The no-fuse breaker and magnetic contactor used should be the EN or IEC standard-compliant products of the models described in Section 13.2.2. (b) The sizes of the cables described in Section 13.2.1 meet the following requirements. To meet the other requirements, follow Table 5 and Appendix C in EN60204-1. Ambient temperature: 40 (104) [ ( )] Sheath: PVC (polyvinyl chloride) Installed on wall surface or open table tray (c) Use the EMC filter for noise redu
ページ11に含まれる内容の要旨
CONFORMANCE WITH UL/C-UL STANDARD (1) Servo amplifiers and servo motors used Use the servo amplifiers and servo motors which comply with the standard model. Servo amplifier series :MR-J2S-10A(1) to MR-J2S-350A(1) Servo motor series :HC-KFS HC-MFS HC-SFS HC-RFS HC-UFS (2) Installation Install a fan of 100CFM air flow 10.16 cm (4 in) above the servo amplifier or provide cooling of at least equivalent capability. (3) Short circuit rating This servo amplifier conforms to the circuit whose p
ページ12に含まれる内容の要旨
CONTENTS 1. FUNCTIONS AND CONFIGURATION 1- 1 to 1-12 1.1 Introduction.............................................................................................................................................. 1- 1 1.2 Function block diagram .......................................................................................................................... 1- 2 1.3 Servo amplifier standard specifications ....................................................................................
ページ13に含まれる内容の要旨
3.9 Servo motor with electromagnetic brake ............................................................................................. 3-52 3.10 Grounding ............................................................................................................................................. 3-55 3.11 Servo amplifier terminal block (TE2) wiring method....................................................................... 3-56 3.12 Instructions for the 3M connector..........................
ページ14に含まれる内容の要旨
7.1.2 Adjustment using servo configuration software............................................................................ 7- 2 7.2 Auto tuning .............................................................................................................................................. 7- 3 7.2.1 Auto tuning mode ............................................................................................................................. 7- 3 7.2.2 Auto tuning mode operation ................
ページ15に含まれる内容の要旨
12.3 Dynamic brake characteristics...........................................................................................................12- 4 12.4 Encoder cable flexing life....................................................................................................................12- 6 13. OPTIONS AND AUXILIARY EQUIPMENT 13- 1 to 13-30 13.1 Options.........................................................................................................................................
ページ16に含まれる内容の要旨
14.12.8 Output signal pin ON/OFF (DO forced output)......................................................................14-24 14.12.9 Alarm history .............................................................................................................................14-25 14.12.10 Current alarm..........................................................................................................................14-26 14.12.11 Other commands...............................................
ページ17に含まれる内容の要旨
Optional Servo Motor Instruction Manual CONTENTS The rough table of contents of the optional MELSERVO Servo Motor Instruction Manual is introduced here for your reference. Note that the contents of the Servo Motor Instruction Manual are not included in the Servo Amplifier Instruction Manual. 1. INTRODUCTION 2. INSTALLATION 3. CONNECTORS USED FOR SERVO MOTOR WIRING 4. INSPECTION 5. SPECIFICATIONS 6. CHARACTERISTICS 7. OUTLINE DIMENSION DRAWINGS 8. CALCULATION METHODS FOR DESIGNING 6
ページ18に含まれる内容の要旨
1. FUNCTIONS AND CONFIGURATION 1. FUNCTIONS AND CONFIGURATION 1.1 Introduction The Mitsubishi MELSERVO-J2-Super series general-purpose AC servo is based on the MELSERVO-J2 series and has further higher performance and higher functions. It has position control, speed control and torque control modes. Further, it can perform operation with the control modes changed, e.g. position/speed control, speed/torque control and torque/position control. Hence, it is applicable to a wide range of fields, not
ページ19に含まれる内容の要旨
1. FUNCTIONS AND CONFIGURATION 1.2 Function block diagram The function block diagram of this servo is shown below. Regenerative brake option Servo amplifier Servo motor P D C (Note2) (Note1) DS RA Power NFB MC U U L1 supply Regenerative 3-phase V V Current L2 brake SM transistor 200 to detector W W L3 CHARGE 230VAC, lamp 1-phase 230VACor Dynamic 1-phase Fan brake 100to120VAC (MR-J2S-200A or more) E1 Electro- L11 Control magnetic E2 power L21 brake supply Regenerative brake Base amplifier Voltage
ページ20に含まれる内容の要旨
1. FUNCTIONS AND CONFIGURATION 1.3 Servo amplifier standard specifications Servo Amplifier MR-J2S- 10A 20A 40A 60A 70A 100A 200A 350A 10A1 20A1 40A1 Item 3-phase 200 to 230VAC, 50/60Hz or 3-phase 200 to 1-phase 100 to Voltage/frequency 1-phase 230VAC, 50/60Hz 230VAC, 50/60Hz 120VAC 50/60Hz 3-phase 200 to 230VAC:170 to 253VAC 3-phase 170 to 1-phase Permissible voltage fluctuation 1-phase 230VAC: 207 to 253VAC 253VAC 85 to 127VAC Permissible frequency fluctuation Within 5% Power supply capacity Re
