ページ1に含まれる内容の要旨
Installation Guide
10/100 Fast Ethernet Switch
with 100FX Connectivity
KS-108F Ver.B Series
DOC.060302-KS108FB
-1-
ページ2に含まれる内容の要旨
(C) 2005 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change. For more information, contact: Unite
ページ3に含まれる内容の要旨
The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including the interference that may cause. CE NOTICE Marking by the symbol indicate
ページ4に含まれる内容の要旨
Table of Contents 1. Introduction ..................................................................5 1.1 Features ........................................................................................... 6 1.2 Specifications .................................................................................. 7 2. Installing the Switch .....................................................9 2.1 Unpacking ....................................................................................... 9 2.2
ページ5に含まれる内容の要旨
1. Introduction This 8-port Fast Ethernet switch series provides seven 10/100 TP ports and one 100BASE-FX fiber port, each capable of transmitting or receiv- ing information simultaneously at full wire speed to control and allocate the network bandwidth. The key features of the switch series are: Optimized Bandwidth : Combining eight 100Mbps-based Fast Ethernet switched ports, the switch delivers a high network bandwidth for your Fast Ethernet network Easy Migration : With 10BASE-T support o
ページ6に含まれる内容の要旨
1.1 Features Designed for resolving congestion problems caused by bandwidth-hun- gry devices and bandwidth-intensive applications as well as a high num- ber of users, the switches not only adhere to the IEEE 802.3 10BASE-T, 802.3u 100BASE-TX and 100BASE-FX standards, but also feature: Seven 10/100BASE-TX auto-negotiation switched ports and one 100BASE-FX port for flexible connections to desktop PCs, servers and Fast Ethernet devices. The 10/100BASE-TX switched ports support: - auto-negotiati
ページ7に含まれる内容の要旨
1.2 Specifications 10/100 Ports IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX std. Shielded RJ-45 jacks with Auto MDI-X detection Auto-negotiation capable Speed for 10Mbps or 100Mbps Full-duplex or half-duplex mode support 100FX Port IEEE 802.3u 100BASE-FX compliant Fixed 100Mbps operation Duplex mode selector - full duplex or half duplex Flow control IEEE 802.3x pause packet for full duplex operation Back-pressure for half duplex operation Cables 10BASE-T Cat. 3, 4, 5 or higher (100 meters max.)
ページ8に含まれる内容の要旨
100FX Port Fiber Specifications KS-108FB-xxx Duplex Series Model Ext Fiber Wavelength Tx Power Sens. Ref.Distance -T ST MMF 1310nm -19 ~ -14dBm -31dBm 2km -C SC MMF 1310nm -19 ~ -14dBm -31dBm 2km -JM MT-RJ MMF 1310nm -19 ~ -14dBm -31dBm 2km -VM VF-45 MMF 1310nm -20 ~ -14dBm -31dBm 2km -SA2 SC SMF 1310nm -15 ~ -8dBm -31dBm 20km -SL2 SC SMF 1310nm -15 ~ -8dBm -32dBm 20km -SL3 SC SMF 1310nm -15 ~ -8dBm -34dBm 30km -SL4 SC SMF 1310nm -5 ~ 0dBm -34dBm 40km -SL6 SC SMF 1310nm -5 ~ 0dBm -35dBm 60k
ページ9に含まれる内容の要旨
2. Installing the Switch 2.1 Unpacking Check to see that you have everything before you start the installation. Installation guide The switch unit One AC power adapter for the unit 2.2 Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. The specifications of the AC power adapter are: AC input power: AC po
ページ10に含まれる内容の要旨
The DC power jack for the AC power adapter is located on the rear of the switch as shown below: 2.3 Installing the Switch 1. Install the switch with the AC power adapter provided. 2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet. -10-
ページ11に含まれる内容の要旨
3. Making Network Connections 3.1 Switched Ports The following figure shows the locations of the switched ports: 3.2 Making UTP Connections 10/100 TP Port Configuration All 10/100 TP ports support configuration as follows: Auto-negotiation capable Highest capability : 100M Full duplex Speed : auto-sensing for 100Mbps or 10Mbps Duplex : Full duplex, Half duplex Auto MDI-X function The following table lists the configuration used for the 10/100 port when it connects to different devices: Connecte
ページ12に含まれる内容の要旨
Cables Depending on the connection speed, use the proper UTP cables: Speed Cables used Distance 100M Cat. 5, 5e, or higher grade 100 meters 10M Cat. 3, 4, 5, 5e, or higher grade100 meters Auto-MDI-X Function An Auto-MDI-X function will automatically detect if a crossover is re- quired and make the swap of Tx pair and Rx pair internally. With this function, straight-through cable can be used for any connection. MDI to MDI-X connection rule is not necessary anymore. In the switches, all TP ports a
ページ13に含まれる内容の要旨
100FX Duplex Selector This selector is used for 100FX port duplex mode selection as follows: The following table lists the maximum MM fiber cable length connecting to different devices: Connected Device Distance (MMF cable) Network card half-duplex fiber port 400 m Network card full-duplex fiber port 2 km Class I hub half-duplex fiber port 160 m 2 Class II hub half-duplex fiber port 112 m Switched half-duplex fiber port 400 m Switched full-duplex fiber port 2 km -13-
ページ14に含まれる内容の要旨
4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the switch as illustrated below: 4.2 Interpretation LED Functions POWER LED : indicates the power status of the switch. LNK/SPD/ACT LED : indicates the link status, connection speed status, and traffic status of the switched port DUP/COL LED : indicates the duplex status and collision status of the switched port LED States and Indications LED State & Color Indication PO
