ページ6に含まれる内容の要旨
LE-565 User’s Manual (The Page is Left For Blank) 6
ページ7に含まれる内容の要旨
LE-565 User’s Manual Introduction Chapter 1 1.1 LE-565 is the 5.25 inch embedded miniboard based on VIA chipset. It integrates VIA embedded chipset for CN700 with VT8237R Plus, DDR 333/400 SDRAM, and serial ATA with RAID to provide the economical embedded platform. VIA CN700 & VT8237R Plus Chipset The board comes with the VIA embedded chipset of CN700, supports DDR 333/400 SDRAM, integrated the S3 Graphics U
ページ8に含まれる内容の要旨
LE-565 User’s Manual Introduction 1.2 General Specification Form Factor 5.25 inch miniboard CPU VIA V4/Eden 1.0GHz processor L1/L2 Cache: 128/128KB Front side bus: 400MHz Memory 1 x 184-pin DDR 333/400 SDRAM up to 1GB,onboard optional 256MB DDR SDRAM Unbufferred, none-ECC memory supported only Chipset VIA CN700 and VT8237R Plus BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS Green Function Power saving mode includes
ページ9に含まれる内容の要旨
LE-565 User’s Manual Introduction Ethernet Interface Chipset REALTEK 8110S-32 Type 10Base-T / 100Base-TX /1000Base-TX auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector Four External RJ45 connectors with LED on rear I/O panel Audio Interface Chipset REALTEK ALC655 Interface 5.1 channel surround audio with Line-in, Line-out and MIC-in Connector Onboard audio connector with pin header Onboard CD-IN connector Expansive
ページ10に含まれる内容の要旨
LE-565 User’s Manual Introduction 1.3 10 Mechanical Drawing
ページ11に含まれる内容の要旨
LE-565 User’s Manual Introduction 1.4 Eden nanoBGA2 CRT/LCD Monitor VT1636 LVDS 1 x 184-pin DDR333/400 Up to 1GB CN700 Ultra V-Link 533MB/s 6 x USB2.0 Ports 2 x SATA 2 x IDE AC97 ALC655 VT8237R+ BIOS LAN1/2/3/4 4 x 8110S-32 4 x Serial ports PCI 1 x Floppy port W83782G 1 x Parallel port 8-bit GPIO Hardware Monitor PS/2 , KB/MS IrDA Block Diagram 11
ページ12に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup Chapter 2 2.1 CN_PWR JLED0/1/2/3 IDE1 CN_USB2/3 CN_INV SYSFAN JFRNT IDE2 DIMM FDD SATA1/2 PCI CN_DIO MINIPCI CN_IR CPUFAN LPT CN_AUDIO CN_LVDS CN_CRT CN_12V CN_COM2/3/4 CDIN CN_PS2 12 Connector Location
ページ13に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup CF DC_IN LAN1/2/3/4 COM1 USB CRT Connector Location 13
ページ14に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.2 Jumper Function JRTC CMOS Operating/Clear Setting JCFSEL Compact Flash address mode setting JVLCD LCD Panel Voltage Setting JAT AT/ATX mode setting JCSEL1/2 COM2 RS232/422/485 mode setting JCFSEL JAT JRTC JVLCD JCSEL1/2 14 Jumper Reference
ページ15に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.3 2.3.1 Connector Function Remark DIMM 184-pin DDR SDRAM DIMM Standard IDE1 40-pin primary IDE connector Standard IDE2 44-pin secondary IDE connector Slim FDD 26-pin slim type floppy connector Slim SATA1/2 7-pin Serial ATA connector Standard CN_12V 4-pin power supply connector Standard CN_AUDIO 5 x 2-pin audio connector Standard CDIN 4-pin CD-ROM audio input conn
ページ16に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.4 2.4.1< CPU> The board supports VIA Eden processor, default ratio is Eden 1G (400MHz) with heatsink only. 2.4.2 The board supports one 184-pin DDR333/400 SDRAM and up to 1GB of capacity, only non-ECC, unbuffered memory is supported. DIMM 104-pin 80-pin Please check the pin number to match the socket side well before installing memory module. 16 CPU and Memory Setup
ページ17に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values. Jumper: JRTC Type: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Normal Operation Default setting Jumper: JAT Type: Onboard 3-pin jumper JAT Mode 1-2 AT mode 2-3 ATX mode -default Default sett
ページ18に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.6 The board supports two enhanced IDE interface, dual channel for 4 ATAPI devices with ATA33. Based on embedded application, the board has one 44-pin IDE connector +5V supported for disk on module. The board also provides a Compact Flash Type II socket with jumper (JCFSEL) selectable slave/Master mode on secondary IDE channel. Jumper: JCFSEL Type: onboard 3-pin header JCFSEL
ページ19に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.7 Based on VIA VT8237R Plus Southbridge, the board supports two Serial ATA interfaces with RAID 0 and 1 array function. The following is the list of the specification of the Serial ATA. 1. Complies with Serial ATA Specification Revision 1.0 2. Dual Channel master mode PCI 3. On-chip two-channel Serial ATA (S-ATA) PHY for support of up to two S-ATA devices directly. 4. S-ATA drive tran
ページ20に含まれる内容の要旨
LE-565 User’s Manual Hardware Setup 2.8 The board provides a slim type floppy port; please use the 26-pin ribbon cable in the package to connect the floppy device. FDD Floppy rear side 4. Lift up this plastic bar 5. Slot the cable in (Blue paste for outside) 6. Press back the plastic bar 1. Lift up the brown plastic bar 2. Slot the cable in (Blue paste for brown bar side) 3. Press back the plastic bar 20 Floppy Port
