ページ1に含まれる内容の要旨
Hughes Installation Configuration and Connections
SYSTEM 4
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: HUGHES
Included Communications Adapter(s):
Quantity Part Number Description
1 26-467-01 ADP, UNV, “A”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT
ページ2に含まれる内容の要旨
Hughes Installation Configuration and Connections Connecting System 4 to Hughes/JVC Projectors If the System 4 is already configured for a Hughes/JVC projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4 is already set up for the Hughes/JVC projector. Apply power t
ページ3に含まれる内容の要旨
Hughes Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (CC 50' or CC 100') into the PJ Comm port on the System 4. The other end has a 9-pin female connector. Plug this end into the other 9-pin male D connector on the HU COM adapter. ______ Secure all of the connector screws. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4 output and those on the other end onto the ma
ページ4に含まれる内容の要旨
Hughes Installation Configuration and Connections System 4- Hughes/JVC Model HJT 100/200 Series Connections Use the illustration below as a guide when connecting the System 4 to a Hughes/JVC HJT 100/200 projector. Refer to Hughes documentation to continue the installation. Hughes HJT 200 Projector Terminal In Control Out Port A (Port B) UNV ADP "A" "A" 26-467-01 3, 4, or 5 BNC Cable CC 50' Connecting the System 4 to a Hughes/JVC HJT 200 Projector ____________ In a rack mount, do NOT all
ページ5に含まれる内容の要旨
Hughes Installation Configuration and Connections Special Instructions for the HJT Model 100/200 Series The projector documentation provides instructions on how to set up and configure the Model 100/200 Series Projector for proper operation with the System 4. The baud rate for the Extron switchers is 19200. Since Port A is locked to a baud rate of 9600, Port B should be used for Extron Switchers. The projector port assignment must be selected and the VIC channel assignment must be edited for a
ページ6に含まれる内容の要旨
Hughes Installation Configuration and Connections Connecting System 4 to Hughes-JVC DILA G1000/G10 Projectors If the System 4 is already configured for a Hughes-JVC DILA projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4 is already set up for the Hughes-JVC DILA
ページ7に含まれる内容の要旨
Hughes Installation Configuration and Connections 5. The Hughes Adapter has two 9-pin connectors, one male and one female. Plug the 9-pin female connector onto the 9-pin male marked “Control Out” (Port B) on the Hughes projector back panel. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (CC 50' or CC 100') into the PJ Comm port on the System 4. The other end has a 9-pin female connector. Plug this end into the other 9-pin male D connector on the HU COM Adapter.
