ページ1に含まれる内容の要旨
SW RGB and SW YUV A Series
Wideband and Component Video and Audio Switchers
68-648-01 Rev. C
Printed in USA
09 04
ページ2に含まれる内容の要旨
Precautions Safety Instructions • English Warning Power sources This equipment should be operated only from the power source indicated on the This symbol is intended to alert the user of important operating and maintenance product. This equipment is intended to be used with a main power system with a grounded (servicing) instructions in the literature provided with the equipment. (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or This symbol is inte
ページ3に含まれる内容の要旨
Quick Start — SW RGB and YUV A Switchers Step 6 — Audio Outputs Installation SW2 RGBHV A / SW4 RGBHV A / SW6 RGBHV A: Step 1 — Remove power Cable audio models for stereo audio output (6). Turn off power to the input and output devices, SW6 YUV A: Connect a digital audio device to this and remove the power cords from them. female BNC connector for a digital audio output. If you are not switching digital Step 2 — Mounting audio, you can use this connector to SW2 — output the composite sync plane
ページ4に含まれる内容の要旨
Quick Start — SW RGB and YUV A Switchers, cont’d Step 7 — Remote Control 7 Connect a host device, such as a computer or touch Pin RS-232 Contact Function 51 panel control via RS-232, OR a remote contact closure 1 — In #1 Input #1 closure device to the switcher via this 9-pin D 2TX — Transmit data (-) connector (7) for remote control of the switcher. — 96 3 RX Receive data (+) Female To command a switch under contact closure 4 — In #2 Input #2 5 Gnd Gnd Signal ground control, momentarily short an
ページ5に含まれる内容の要旨
Table of Contents Chapter 1 Introduction ....................................................................................................... 1-1 About the Switchers ......................................................................................................... 1-2 Features ................................................................................................................................... 1-3 Audio switching models ...................................................
ページ6に含まれる内容の要旨
Table of Contents, cont’d Chapter 4 Remote Control ................................................................................................ 4-1 Simple Instruction Set ...................................................................................................... 4-2 Host-to-switcher instructions ............................................................................................ 4-2 Switcher-initiated (unsolicited) messages ...............................................
ページ7に含まれる内容の要旨
SW RGB and YUV A Switchers Chapter One 1 Introduction About the Switchers Features
ページ8に含まれる内容の要旨
INPUT BUFFERED LOCAL H . SH IFT MON ITOR OUTPUT VGA INTERFAR CG EB W 1 0 /A 9D xS iP Intr Introduction, cont’d oduction About the Switchers The Extron SW RGB and YUV A series (figure 1-1) is a family of six RGB video switchers and one component video switcher, some with audio, in an array of input and output configurations. The models available are: SW2 RGBHV (two RGB video inputs) SW2 RGBHV A (two RGB inputs and two balanced or unbalanced stereo or mono audio inputs) SW4 RGBHV (four RGB
ページ9に含まれる内容の要旨
Features Audio switching models Inputs — These switchers input 2, 4, or 6 stereo audio signals, balanced or unbalanced, on 3.5 mm, 5-pole captive screw terminals. Outputs — The selected audio input is buffered and output, balanced or unbalanced, on a 3.5 mm, 5-pole captive screw terminal. Audio gain/attenuation — Users can set the input level of audio gain or attenuation (-18 dB to +24 dB) via the RS-232 link or from the front panel, to be compatible with a wide range of line level (from -20 dBV
ページ10に含まれる内容の要旨
Introduction, cont’d All models Bandwidth — Bandwidth is 350 MHz (-3 dB). This high bandwidth allows the switchers to switch all of the high-resolution video signals with no loss of signal quality. Input signal sensing — The switcher continuously monitors all inputs to sense when the input signal is active or inactive. The switcher reports changes in the status of each input (active to inactive or inactive to active) on the RS-232 port. Autoswitching mode — When autoswitching is enabled, the s
ページ11に含まれる内容の要旨
SW RGB and YUV A Switchers Chapter Two 2 Installation Installation Overview Mounting the Switcher Cabling and Rear Panel Views
ページ12に含まれる内容の要旨
Installation, cont’d Installation Installation Overview Install an SW RGB or SW YUV A Series switcher as follows: 1 Turn off the input and output devices, and unplug their power cables. 2 If desired, mount the switcher in a rack, under furniture, or through furniture. See Mounting the Switcher below. 3 Connect the input and output devices to the switcher (see Cabling and Rear Panel Views on page 2-6). If desired, connect a computer, RS-232 control system, or contact closure 4 device to the Remot
ページ13に含まれる内容の要旨
SW2 RGBHV A RGBHV & AUDIO SWITCHER 2 AUDIO 1 AUTO SWITCH -dB +dB ACUTIVE CONF/SAVE Use 2 mounting holes on opposite corners. False front panel uses 2 front holes. (2) 4-40 x 3/16" Screws Figure 2-1 — Rack mounting an SW2 switcher Mounting Screws (2 Plcs) Drill pilot holes Each Side 3/32” (2.4mm) dia. 1/4” (6.3 mm) deep. Rack-mount Bracket or Table/ #8 Screw (4 Plcs) Wall-mount Each Side Bracket Figure 2-2 — Rack or table mounting an SW4 or SW6 switcher SW RGB and YUV A Switchers Installation 2
ページ14に含まれる内容の要旨
SW2 RGBHV RGBHV & AUDIO SWITCHER 1 2 AUTO SWICH ACUTIVE Installation, cont’d Under furniture mounting the switcher The SW2 switcher models can be mounted under a table or other horizontal surface with an optional Extron under-desk mounting kit (part #70-077-01). The SW4 and SW6 switcher models can be mounted under a table or other horizontal surface with an optional Extron 1U under-desk mounting kit (part #70-222-01). SW2 models 1. Secure the optional under-desk mounting brackets to the switche
ページ15に含まれる内容の要旨
AUTO SWITCH IV SW2 RGBHV RGBHV & AUDIO SWITCHER 1 2 ACT E 3. Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot holes in the table or desk at the marked screw locations from the underside/inside (concealed side) of the furniture, where the switcher will be located. 4. Insert the four wood screws into the pilot holes. Fasten each screw into the installation surface until just less than 1/4" of the screw head protrudes. 5. Align the installed screws with the slots in the mounting brackets, and
ページ16に含まれる内容の要旨
Installation, cont’d 5. Slide the switcher up and down or back and forth in the mounting brackets until the face of the switcher is at the desired height. Tighten the screws that secure the bracket in place. If the screws are inaccessible to a screwdriver: a. Mark the location of the brackets relative to the screws. b. Remove the switcher from the underside of the surface. c. Tighten the screws. d. Replace the switcher on the underside of the surface (step 4). Cabling and Rear Panel Views All c
ページ17に含まれる内容の要旨
Inputs 1 RGB and component video inputs — RGB models — For each input, connect an RGBHV, RGBS, RGsB, RsGsBs, or component video source to these BNC connectors. Connect the cables as shown in figure 2-8. SW6 YUV A — For each input, connect a component video, RGsB, or RsGsBs source to one of these BNC connectors. If you are not switching digital 3 audio, you can use the Digital Audio input BNCs ( ) for the composite sync plane of RGBS video inputs. Connect the cables as shown in figure 2-8. RGB
ページ18に含まれる内容の要旨
Installation, cont’d The audio level for each input can be individually set, via the front panel or under RS-232 control, to ensure that the level on the output does not vary from input to input. See chapter 3, Operation, and chapter 4, Remote Control for details. Digital audio input connections (SW6 YUV A only) — Each input has a 3 female BNC connector for a digital audio input. If you are not switching digital audio, you can use this connector to input the composite sync plane of RGBS video.
ページ19に含まれる内容の要旨
Remote connection 7 Remote connector — Connect a host device, such as a computer or touch panel control, or a remote contact closure device to the switcher via this 9-pin D connector (figure 2-11) for remote control of the switcher. See chapter 4, Remote Control, for definitions of the SIS commands, details on how to install and use the control software, and information on how to make a remote contact closure device. Pin RS-232 Contact closure Function 51 1 — In #1 Input #1 2TX — Transmit data (
ページ20に含まれる内容の要旨
Installation, cont’d 2-10 SW RGB and YUV A Switchers Installation
