ページ1に含まれる内容の要旨
Setup Guide
Setup Guide
Matrix Switchers
DXP DVI Pro
DXP HDMI
DVI and HDMI
Matrix Switchers
68-1370-50 Rev. C
03 12
ページ2に含まれる内容の要旨
Safety Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source indicated This symbol is intended to alert the user of important on the product. This equipment is intended to be used with a main power system with a operating and maintenance (servicing) instructions in grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt the literature provided with the equipment. to bypass or disabl
ページ3に含まれる内容の要旨
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 注意 己试图打开设备盖子维修该设备。 阅读说明书 • 用户使用该设备前必须阅读并理 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 解所有安全和使用说明。 机内敏感元件过热。 不要用任何东西挡住通风孔。 保存说明书 • 用户应保存安全说明书以备将来使 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 用。 与厂家推荐的相同或相近型号的电池。 按照生产厂的 遵守警告 • 用户应遵守产品和用户指南上的所有安 建议处理废弃电池。 全和操作说明。
ページ4に含まれる内容の要旨
Conventions Used in this Guide In this user guide, the following are used: CAUTION: A caution indicates a potential hazard to equipment or data. NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier. WARNING: A warning warns of things or actions that might cause injury, death, or other severe consequences. Copyright © 2012 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide ar
ページ5に含まれる内容の要旨
Contents Introduction .......................................1 Remote Control ...............................21 About this Guide ................................1 Establishing a Network About the DXP DVI Pro and DXP (Ethernet) Connection ...................21 HDMI Series Matrix Switchers ..........1 Connection Timeouts...................22 Application Diagram Examples .........2 Number of Connections ..............22 Verbose Mode ..............................22 SIS Commands .................
ページ6に含まれる内容の要旨
vi DXP DVI Pro and DXP HDMI Series • Contents
ページ7に含まれる内容の要旨
Introduction This section gives an overview of the Extron DXP 44/48/84/88 DVI Pro and DXP 44/48/84/88 HDMI Series Digital Matrix Switchers and provides application examples. The following topics are covered: • About this Guide • About the DXP DVI Pro and DXP HDMI Series Matrix Switchers • Application Diagram Examples NOTE: For more information on any subject in this guide, see the DXP DVI Pro and DXP HDMI Series Digital Matrix Switchers User Guide, available on the Extron Product Software DV
ページ8に含まれる内容の要旨
The DXP DVI Pro and DXP HDMI series all provide easy integration in applications that require reliable DVI or HDMI signal routing. (A "DVI Pro" signal is HDCP-compliant; a standard DVI signal is not.) They include several convenience features common to Extron matrix ™ switchers such as the QuickSwitch Front Panel Controller (QS-FPC ), ® global presets, IP Link , and Ethernet control. NOTES: • The DXP DVI Pro fully supports HDMI video and embedded audio signals when optional Extron DVI-t
ページ9に含まれる内容の要旨
P L A Y S T A T I O N 3 Display 1Display 5 Display 3 Display 7 Display 2D Display 4 isplay 6 Display 8 HDMI - HDCP COMPLIANT LAN HDMI INPUTS HDMI OUTPUTS Extron 13 24 13 24 HDMI 201 Tx Extron 5 6 78 5 6 78 HDMI Twisted IPL 250 LISTED C U S1T23 Pair Extender I.T.E. IP Link Ethernet POWER HDMI 201 Tx 12 0.4A MA V X HDMI INPUT REMO DDC TE RS-232 ON PASS THRU N/A 12 12 LOCAL Tx Rx Control Processor Extron TX RX COM RT 1 S CTS TX COM RX 2 1 IR 2 1 RELAY2 POWER LAN SGSG 500m 12V A DXP HDM
ページ10に含まれる内容の要旨
4 DXP DVI Pro and DXP HDMI Series • Introduction
ページ11に含まれる内容の要旨
Setup This section describes the rear panels of the DXP switchers and provides instructions for cabling. It covers the following topics: • Setup Procedure • Rear Panels and Connections • Front Panel Config Port Setup Procedure Follow these steps to set up and start operating the DXP switcher. See the "Operation" section for additional configuration procedures you may want to perform to set up the switcher. 1. Turn off power to the input and output devices and disconnect their power cords. 2.
ページ12に含まれる内容の要旨
Rear Panels and Connections Most of the connectors are on the rear panels of the DXP switchers. The following figures show the rear panels of the four DVI models and the four HDMI models. NOTE: The illustrations below show DXP 88 DVI Pro and DXP 88 HDMI models, with 8 input and 8 output connectors. The rear panels of the other DXP models are identical to these models except for the number of inputs and outputs (see "About the DXP DVI Pro and DXP HDMI Series Matrix Switchers" in the "Intr
ページ13に含まれる内容の要旨
Input connectors — b • DVI Pro series: Connect DVI-D source devices to these female 29-pin DVI-I input connectors. Only single-link DVI-D signals are supported. • HDMI series: Connect HDMI source devices to these female 19-pin type A HDMI input connectors. LockIt™ cable lacing brackets, one for each HDMI input and output connector, are provided with the DXP HDMI. These brackets can be used to secure the HDMI cables to the DXP connectors to reduce stress on the HDMI connectors and preven
ページ14に含まれる内容の要旨
Output connectors — c NOTE: The switchers do not alter the video signal in any way. The signal that is output by the switcher is in the same format as the input signal. • DVI Pro series: Connect DVI output devices to these female 29-pin DVI-I output connectors. • HDMI series: Connect HDMI output devices to these female 19-pin type A HDMI output connectors. Ethernet port — If desired, connect the DXP switcher to a d computer, a network WAN or LAN hub, or a control system via this RJ-45 c
ページ15に含まれる内容の要旨
The cable you use depends on your network speed. The switcher supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps (100Base-T — Fast Ethernet), half-duplex and full-duplex, Ethernet connections. • 10Base-T Ethernet requires CAT 3 or higher UTP or STP cable. • 100Base-T Fast Ethernet requires CAT 5e or higher UTP or STP cable. Terminate the Ethernet cable as required: • Network connection — Wire as a patch (straight-through) cable. • Computer or control system connection — Wire as a
ページ16に含まれる内容の要旨
Remote RS232/RS422 connector — Connect an RS-232 capable g host device such as a computer or a touch panel control to the switcher via this 9-pin D connector for serial RS-232 or RS-422 control. Pin RS-232 Function RS-422 Function 1 — Not used — Not used 1 2 Tx Transmit data Tx– Transmit data (–) 6 3 Rx Receive data Rx– Receive data (–) 4 — Not used — Not used 9 5 5 Gnd Signal ground Gnd Signal ground 6 — Not used — Not used 7 — Not used Rx+ Receive data (+) 8 — Not used Tx+ Transmit data (+
ページ17に含まれる内容の要旨
An optional 9-pin D to 2.5 mm mini jack TRS RS-232 cable, part number 70-335-01, is available to connect to this port. (The port does not support RS-422.) The figure below shows the pin assignments for this cable. 6 feet (1.8 m) Part #70-335-01 1 6 6 9 9 5 Tip Ring Sleeve (Gnd) 9-pin D Connection TRS Plug Pin 2 Computer Rx line Tip Pin 3 Computer Tx line Ring Pin 5 Computer signal ground Sleeve Figure 9. 2.5 mm Connector Cable for the Configurati
ページ18に含まれる内容の要旨
12 DXP DVI Pro and DXP HDMI Series • Introduction
ページ19に含まれる内容の要旨
Operation This section describes the DXP front panel controls and the procedures to configure and begin to operate the DXP switchers. For additional operations and more details, see the DXP DVI Pro and DXP HDMI Series User Guide, available from the provided Extron software disc or from the Extron website at www.extron.com. Topics include: • Front Panel Features • Operations Front Panel Features The front panels of all DXP models have the same controls and layout (shown below). The front p
ページ20に含まれる内容の要旨
Config port — This RS-232 port is an alternative to the rear panel c Remote RS232/RS422 connector. It supports RS-232 only. For more information about the Config port, see "Front Panel Config Port " in the "Setup" section. Enter button — The Enter button has three primary functions: d • Saves changes that you make on the front panel. • Indicates that a potential tie has been created but not saved. • Indicates that a global preset has been selected to be saved or recalled but the preset a
