ページ1に含まれる内容の要旨
Installation Manual
5100 Series, Catalog 5150
Connectivity Module
For use with Automatic Transfer Switches,
Power Manager, & Digital Power Meter
Section Page
Welcome............................................................................................................. ii
Overview, Specifications, Installation Overview, DIP Switch (RS485)..........
ページ2に含まれる内容の要旨
ii Welcome Connectivity Module Who Should Use this Installation Manual This manual for the Connectivity Module should be used to assist individuals who will: • install the Connectivity Module (mount and wire) • configure the Connectivity Module • enter in information about your Automatic Transfer Switches (7000 & 4000 Series, Series 300, ASCO 940,962,436,434,447,448) • use Ethernet access to monitor Connectivity Module (connected devices) ® Prerequisites A working k
ページ3に含まれる内容の要旨
Connectivity Module Overview, Specifications, Installation Overview, DIP Switch iii Overview Installation Overview The Connectivity Module brings together several different serial devices that communicate at different 1. Determine the kind of network to use to connect the baud rates and with different protocols to a common various devices to the Connectivity Module. Ethernet media. It can communicate with up to eight 2. If a RS485 network will be used, do not install the cli
ページ4に含まれる内容の要旨
iv Outline and Mounting Drawing Connectivity Module
ページ5に含まれる内容の要旨
v Wiring Diagrams Connectivity Module
ページ6に含まれる内容の要旨
Connectivity Module Wiring Diagrams vi
ページ7に含まれる内容の要旨
vii Wiring Diagrams Connectivity Module
ページ8に含まれる内容の要旨
Connectivity Module Wiring Diagrams viii
ページ9に含まれる内容の要旨
Connectivity Module Status LEDs ix Status LEDs LED LED Description LED Function / Mode of Operation Solid GREEN – functioning as a Connectivity Module (Acc. 72E). Power indication status. POWER GREEN/AMBER Solid AMBER – functioning as a Serial Module (Acc. 72A). Data receiving status. RX Blinking GREEN – indicates receiving data from a client. GREEN Data transmit status. Blinking GREEN – indicates transmitting data to a client. TX GREEN
ページ10に含まれる内容の要旨
1-1 Installation Connectivity Module How to Install the Connectivity Module How to Install the Connectivity Module on 7000 & 4000 Series and Series 300 ATSs on ASCO 940/962 ATSs The Connectivity Module (CM) mounts on a DIN rail The Connectivity Module (CM) mounts on a DIN rail under the ATS Controller (Group 5 & 1). A short serial near the ATS Control Panel. A separate power supply is cable connects the CM to the Controller. If a Power needed unless it is connected to a Power Ma
ページ11に含まれる内容の要旨
Connectivity Module Installation 1-2 How to Install the Connectivity Module for How to Test Communication to the a stand-alone Power Manager or Digital Connectivity Module Power Meter You need the following settings from your network administrator for each Connectivity Module (CM) The Connectivity Module (CM) mounts on a DIN rail connected to an Automatic Transfer Switch (ATS), Power near the Power Manager (PM) or Digital Power Meter Manager (PM), or Digital Power Meter (DP
ページ12に含まれる内容の要旨
1-3 Installation Connectivity Module How to View & Change Configuration Pages How to View Pages from a Connectivity from a Connectivity Module Module after it is installed To view and change configuration pages on a client After installation, testing, and configuration is completed, computer, follow these steps: to view pages on a client computer, follow these steps: 1. Be sure that your computer is connected to the Internet. 1. Be sure that your computer is connected t
ページ13に含まれる内容の要旨
Connectivity Module 7000 & 4000 Series ATSs 2-1 Device Configurator Screen for 7000 & 4000 Series ATSs The Device Configurator Screen for 7000 & 4000 Series ATSs shows the Group 5 controller configuration settings (right side) and Connectivity Module (server) configuration settings (left side) for the selected ATS. Group 5 Controller Configuration (right side) Enter or change the ATS Name (8 char. max.)and the ATS Location (20 char. max.). Press the Update button when finished t
ページ14に含まれる内容の要旨
2-2 7000 & 4000 Series ATSs Connectivity Module Device Configurator Screen for 7000 & 4000 Series ATSs with a PM or DPM If a Power Manager (PM) or Digital Power Meter (DPM) is used with a 7000 & 4000 Series ATS, a button appears on the lower left corner of the Connectivity Module Device Configurator screen. Press the Config PM button to display the Power Manager or Power Meter Configuration screen (right side). Power Manager or Power Meter Configuration Enter or change the PM
ページ15に含まれる内容の要旨
Connectivity Module 7000 & 4000 Series ATSs 2-3 Detail Screen for 7000 & 4000 Series ATSs The Detail Screen for 7000 & 4000 Series ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, event logging, and other status indications. ATS one-line icon shows position & source status (green or red circle means source is acceptable, grey circle means source is not acceptable) ATS location Active time delays ATS name Status of Nor
ページ16に含まれる内容の要旨
3-1 Series 300 ATSs Connectivity Module Device Configurator Screen for Series 300 ATSs The Device Configurator Screen for Series 300 ATSs shows the Group 1 controller configuration settings (right side) and the Connectivity Module (server) configuration settings (left side) for the selected ATS. Group 1 Controller Configuration (right side) Enter or change the ATS Name (8 char. max.) and the ATS Location (20 char. max.). Press the Update button when finished to save the Group
ページ17に含まれる内容の要旨
Connectity Module Series 300 ATSs 3-2 Device Configurator Screen for Series 300 ATSs with a PM or DPM If a Power Manager (PM) or a Digital Power Meter (DPM) is used with a Series 300 ATS, a button appears on the lower left corner of the Connectivity Module Device Configurator screen. Press the Config PM button to display the Power Manager or Power Meter Configuration screen (right side). Power Manager or Power Meter Configuration Enter or change the PM or DPM Name (8 char. max.
ページ18に含まれる内容の要旨
3-3 Series 300 ATSs Connectivity Module Detail Screen for Series 300 ATSs The Detail Screen for Series 300 ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, and other status indications. ATS one-line icon shows position & source status (green or red circle means source is acceptable, grey circle means source is not acceptable) Status of ATS location Emergency Source ATS type ATS name Status of Normal Source Actua
ページ19に含まれる内容の要旨
Connectivity Module ASCO 940/962 ATSs 4-1 Device Configurator Screen for ASCO 940/962 ATSs The Device Configurator Screen for ASCO 940/962 ATSs shows the Group 7A controller configuration settings (right side) and the Connectivity Module (server) configuration settings (left) for the selected ATS. Group 7A Controller Configuration (right side) Enter or change the ATS Name (18 char. max.) and ATS Nominal Voltage (must be entered to get correct reading). Press the Update button
ページ20に含まれる内容の要旨
4-2 ASCO 940/962 ATSs Connectivity Module Detail Screen for ASCO 940/962 ATSs The Detail Screen for ASCO 940/962 ATSs shows the switch location, ratings, timer settings, actual timer values, pickup and dropout settings, and other status indications. ATS one-line icon shows position & source status (green or red circle means source is acceptable, grey circle means source is not acceptable) Status of ATS name Status of Normal Source Emergency Source Actual voltage Actua
