ページ1に含まれる内容の要旨
User’s Manual
Monochrome LCD Monitor
It shall be assured that the final system is in compliance to
IEC60601-1-1 requirements.
ページ2に含まれる内容の要旨
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. • Power supplied equipment can emit electr
ページ3に含まれる内容の要旨
English TABLE OF CONTENTS PRECAUTIONS................................................................................4 1. INTRODUCTION .....................................................................................9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors ...........
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage. Do not open the cabinet or modify the unit. Opening the cabinet or modifying the unit may result in fire, electric shock, or burn. Refer all servicing to qualified service personnel. Do
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
English LCD Panel The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. Do not press on the panel or edge of the frame strongly, as this may result in damage to the screen. There will be prints left on the screen if the
ページ9に含まれる内容の要旨
English 1. INTRODUCTION Thank you for choosing an EIZO Monochrome Monitor. 1-1. Features • DVI Digital input compliant (see p.33 ; for TMDS, see p.33) • [Horizontal scanning frequency] 31 - 100 kHz [Vertical scanning frequency] 48 ~ 71.5 Hz (VGA text: 69 - 71 Hz) [Resolution] 3M pixels (Portrait: 1536 × 2048 dots (H × V)) [Frame synchronous mode] 59 - 61 Hz supported • Cal Switch function for selecting an optimal calibration mode (see p.17) • Selectable screen compliant with DI
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
English 2. CABLE CONNECTIONS 2-1. Before Connecting Before connecting your monitor to the PC, change the display screen settings resolution (see p.33) and frequency in accordance with the charts below. NOTE • When your computer and display support VESA DDC, the appropriate resolution and the refresh rate are set just by plugging your display into the computer without any manual settings. Resolution Frequency Dot Clock Display mode Portrait Landscape 720×400 VGA TEXT 70 Hz 165 MHz √
ページ13に含まれる内容の要旨
English 2. Connect the signal cable to the DVI-D input connector on the rear of the monitor and to the video output connector on the PC. After connecting, secure the cable connectors with the attached screw-in fasteners. Signal cable FD-C39 Power cord Signal Cable Connector PC Signal cable (FD-C39) Video output connector / DVI Exclusive graphics board (See p.31) 3. Connect the power cord to the power connector on the rear of the monitor. 4. Thread the power cord and signal cable
ページ14に含まれる内容の要旨
English 5. Connect the other end of the power cord to a power outlet. The monitor's power indicator will flash orange slowly. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. 6. Turn on the monitor's power
ページ15に含まれる内容の要旨
English 3. MENUS & FUNCTIONS 3-1. ScreenManager Screen adjustments and settings can be performed with the monitor controls. ScreenManager main menu Directing Switches CAL Switch menu Left, Down, Up, Right Enter Switch NOTE • The ScreenManager menu and CAL Switch menu cannot be displayed at the same time. How to use the ScreenManager [Entering the ScreenManager] (1) Touch the enter switch. [Making adjustments and settings] (1) Select the desired submenu icon with the directi
ページ16に含まれる内容の要旨
English ScreenManager Menus and Settings. The following table briefly explains each of the menus and settings in the ScreenManager. Main menu Sub menu Explanation Setup Signal Selection See 3-3. Other Useful Functions (p. 18) Mode Preset Mode Brightness See 4-1. Brightness Adjustment (p. 21) Reset PowerManager DVI DMPM See 4-3. Power-save Setup (p. 21) Others Border Intensity See 4-2. Image Adjustments Off Timer Turn off the monitor after a specified time (see p. 20). Menu Menu Po
ページ17に含まれる内容の要旨
English 3-2. CAL Switch Function This function allows you to select the optimal display mode for your display images and adjust the brightness in each mode. CAL Switch Modes Mode Description 1-DICOM Select this option to display images in the DICOM mode (see p. 33). 2-Native Select this option to display images using the native characteristics of the monitor panel. 3-CAL Used for monitor calibration * All modes can be calibrated independently. The mode name can also be changed usi
ページ18に含まれる内容の要旨
English 3-3. Other Useful Functions Hardware Rotation This function allows you to rotate the monitor image 90 degrees without using special software or graphics board utilities. [How to set] (1) Shut down the computer if it is running. Also, turn off the monitor by touching the power switch on the control panel. (2) Turn off the monitor power. (3) Touch the power switch while touching the mode switch on the conrtol panel. The menu appears. Orientation Menu Mode Switch
ページ19に含まれる内容の要旨
English Mode Preset When CAL Switch mode is selected, the computer can be forced to display only specified modes. Use this function when the display modes are restricted or when the display should not be changed needlessly. [How to set] (1) Select in the ScreenManager menu. (2) Set each mode to “On” or “Off”. NOTE • You cannot disable all modes. Set one or more modes to “On”. [How to cancel] (1) Select in the ScreenManager menu. (2) Set
ページ20に含まれる内容の要旨
English Off Timer The off timer function causes the monitor to turn off automatically after a predetermined amount of time has lapsed. This function was created to reduce the afterimages particular to LCD monitors, which appear when the screen is left on for long periods without use. [How to set] (1) Select in the ScreenManager menu. (2) Select “Enable” and touch the Right and Left directing switches to adjust the “On Period” (1 to 23 hours). [Off timer system]
