ページ1に含まれる内容の要旨
DES-802
10/100 Fast Ethernet Switch
User’s Guide
Rev. 02 (November, 1997)
6DES802...02
Printed In Taiwan
RECYCLABLE
ページ2に含まれる内容の要旨
Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät is vor Feuchtigkeit zu schützen. 6. Bei der Auf
ページ3に含まれる内容の要旨
Limited Warranty Hardware: D-Link warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following lengths of time from the date of purchase from D-Link or its Authorized Reseller: Product Type Warranty Period Managed Switch Three Years Unmanaged Switch Lifetime If a product does not operate as warranted during the applicable warranty period, D-Link shall, at its option and expense, (1) repair the defective product or part, (2)
ページ4に含まれる内容の要旨
WARRANTIES EXCLUSIVE IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LI
ページ5に含まれる内容の要旨
Trademarks Copyright 1997 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the Unite
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide TABLE OF CONTENTS PREFACE .........................................................................ix Purpose..................................................................................................... ix Audience ................................................................................................... ix Manual Organization ................................................................................ x CHAPTER 1 : OVERVIEW........
ページ8に含まれる内容の要旨
10/100Mbps Mode Operations: Port 2..............................................................13 Setting the Duplex Mode.......................................................................... 13 Network Configuration Examples............................................................ 15 APPENDIX A : SPECIFICATIONS ..........................................17 APPENDIX B : CONNECTOR PINOUTS..................................19 RJ-45 Connectors .................................................
ページ9に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide PREFACE Congratulations on your purchase of the 10/100 Fast Ethernet Switch. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. Purpose This manual discusses how to install and use the 10/100 Fast Ethernet Switch. Audience This manual is intended for network administrators with: • Background in LAN bridge concepts. • Understanding of IEEE 802.3 Ethernet and 100BASE-TX Fast Ethernet networkin
ページ10に含まれる内容の要旨
Manual Organization Chapter 1 Overview Describes the product, its features, packing list, and the front and rear panels. Chapter 2 Installation Provides detailed instructions on installing the 10/100 Fast Ethernet Switch. Chapter 2 includes information on table and wall-mounted installation, connecting power, network connections, setting the communications mode and cascade, and provides some network configuration examples. Appendix A Specifications Lists the technical specifications of the pr
ページ11に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide 1 2 O VERVIEW Introduction The 10/100 Fast Ethernet Switch is an ideal device for linking Ethernet LANs without impacting available bandwidth or for integrating 100Mbps Fast Ethernet with 10Mbps Ethernet networks. The speed migration design will bridge a bandwidth-intensive Fast Ethernet network and a traditional 10Mbps Ethernet network. The 10/100 Fast Ethernet Switch complies with IEEE802.3u, 100BASE-TX, IEEE802.3 and 10BASE-T standards. The switch ha
ページ12に含まれる内容の要旨
Product Features The 10/100 Fast Ethernet Switch has the following key features: • One 3-in-1 Combo Port: UTP/STP (N-Way), BNC, and AUI. • One 10/100Mbps, N-Way UTP/STP port. • Full-duplex and half-duplex capability on both ports (applies only to the twisted-pair connector on the combo port); user-configurable through the Duplex Mode Switch. • Support for IEEE 802.3, 10BASE-2, 10BASE-T, IEEE 802.3u and 100BASE-TX standards. • Ability of both ports to connect to a LAN segment up to 100 meters lon
ページ13に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide • An AC Power Cord • A Wall Mount kit ( 2 tapping screws and 2 screw anchors) • Rubber Feet Front Panel The 10/100 Fast Ethernet Switch front panel includes network connectors and LED indicators for ease-of-use. Figure 1 : 10/100 Fast Ethernet Switch Front Panel Ports The product comes with two ports. These ports can be used to connect to individual stations, to LAN segments that include multiple hubs, and to other 100BASE-TX/10BASE-T switches. Importan
ページ14に含まれる内容の要旨
Port 1: 3-in-1 Combo Port 1 has three different connectors – UTP/STP, BNC, and AUI. The twisted-pair connector (UTP/STP) of Port 1 is a 10/100Mbps, N-Way RJ-45 port for use with unshielded or shielded twisted-pair cabling. Because it is an N-Way port, the operating mode of connected stations (10Mbps Ethernet or 100Mbps Fast Ethernet) is automatically detected and the port is auto-configured to match. Please use crossover cabling unless you are connecting to a straight-through uplink port on a
ページ15に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide Port 2: 10/100Mbps, N-Way UTP/STP Port 2 operates at an user-selectable effective speed of 10 or 100Mbps for half-duplex mode and 20 or 200Mbps for full-duplex mode. It is an N-Way port, so it auto-detects and auto-configures according to the operating standard (10Mbps Ethernet or 100Mbps Fast Ethernet) of connected devices. Port 2 can operate up to 100 meters of Category 3, 4 or 5 shielded twisted- pair or unshielded twisted-pair (STP/UTP) cable. Pleas
ページ16に含まれる内容の要旨
LED Indicators The 10/100 Fast Ethernet Switch has extensive LED indicators to facilitate monitoring and troubleshooting. They include a Power LED and Status LEDs for both ports. The Status LEDs have indicators that report on Link, Duplex, Activity, Collision and 100Mbps states. Figure 2 : LED Indicators The following section describes these indicators in detail. • Power LED This indicator is green when power is supplied to the device. The Power LED lights when you connect the power cable to
ページ17に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide • 100M LEDs These indicators are green when port 1 or port 2 is connected to a device operating at 100Mbps. If either of these LEDs is off, then the port it corresponds to is either not connected or is connected to a device operating at 10Mbps. • FDX/Col (Collision) LED This indicator is green when the respective port is operating in full- duplex mode, and blinks yellow when collisions occur. Rear Panel The rear panel of the 10/100 Fast Ethernet Switch
ページ18に含まれる内容の要旨
8 Overview
ページ19に含まれる内容の要旨
10/100 Fast Ethernet Switch User’s Guide 2 3 INSTALLATION This chapter describes the installation procedure for the 10/100 Fast Ethernet Switch. The chapter includes information on installation locations, connecting power, connecting network cables, setting the port duplex mode, cascading, and network configuration examples. Installation Site You have the option to install the product on a table or mount it on a wall. When installing, choose a sturdy, level surface in a ventilated area that is
ページ20に含まれる内容の要旨
• Site should not exceed the electromagnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength. • The power outlet should be within 6 feet of the device. For a detailed list of the product’s technical specifications, refer to Appendix A, Specifications. Installing on a Desktop or Shelf When installing the product on a table you need to attach the rubber feet included with the device. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilatio
