ページ1に含まれる内容の要旨
USB Multi-port
Hub
User Manual
P73277 F5U116
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Introduction Please read this manual thoroughly in its entirety. Failure to follow installation and other recommended procedures may result in irreversible damage to the product, your computer and/or connected devices. Thank you for purchasing the Belkin Components F5U116 Multi-port Hub. This product provides you with the following ports: • Four downstream USB ports • One parallel printer port • Two RS-232 serial ports USB has a simple and high-speed interface which makes adding serial devices
ページ4に含まれる内容の要旨
Product Detail System Requirements • PC with one free USB port ® • Windows 98/98 Second Edition (SE) • CD-ROM drive 2
ページ5に含まれる内容の要旨
Hardware Installation Because USB is hot swappable, you need not power down your PC. • Connect the jack of the power adapter and plug it into the back of the Multi-port Hub • Find an unused electrical outlet, and plug in the power adapter • Plug the flat end (A plug) of the USB cable into a free USB port on your PC • Plug the square end (B plug) of the USB cable into the USB upstream connector located on the back of the Multi-port Hub ® Windows will automatically detect the Multi-port Hub and
ページ6に含まれる内容の要旨
Software Installation ® ® Software Installation – Windows 98 and Windows 98 Second Edition (SE) ® First, Windows will automatically detect and install the built-in "General Purpose USB Hub" for the four downstream USB ports. You do not need to do anything. ® Next, Windows will detect the two serial ports named "USB-232 Adapter". You see the following dialog box: Click on Next. 4
ページ7に含まれる内容の要旨
Software Installation (continued) ® At the next prompt, click on Next again so that Windows searches for the best driver (recommended): ® You must then tell Windows where to get the drivers. Insert the CD-ROM in your CD-ROM drive, and click on “Specify a location”. In the space provided, type “d:\serial\win98” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on Next. 5
ページ8に含まれる内容の要旨
Software Installation (continued) ® Windows will read the CD-ROM and find the correct drivers. Click on Next. ® Once Windows has finished copying the drivers, installation for the first serial port is complete. Click on Finish: ® Windows may prompt you to restart your computer. Because installation is not yet complete, click No. 6
ページ9に含まれる内容の要旨
Software Installation (continued) ® Windows will continue, and will detect and install the drivers ® for the second serial port. Then, Windows 98 will find an ® “Unknown Device”. Windows 98 SE will find this device as a “USB Device”. Click on Next. ® At the next prompt, click on Next again so that Windows searches for the best driver (recommended): 7
ページ10に含まれる内容の要旨
Software Installation (continued) ® You must then tell Windows where to get the drivers. Make sure the Installation CD is in your CD-ROM drive, and click on “Specify a location”. In the space provided, type in “d:\parallel\win98” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on Next. ® Windows will read the CD-ROM and find the correct drivers. Click on Next. 8
ページ11に含まれる内容の要旨
Software Installation (continued) ® Once Windows has completed copying the files, you will see the following confirmation. Click Finish. ® Windows may prompt you to restart your computer. Installation is complete, and restarting is necessary to properly configure the system registry. Click Yes. 9
ページ12に含まれる内容の要旨
Software Installation (continued) ® Windows should copy all the files it needs and install the ® Multi-port Hub completely. Windows will begin installing the USB COM ports as COM_A and COM_B on your computer, where A and B are unused COM ports (A and B can be any number from 2 to 10). It will also finish installing the Parallel Port. You can verify whether all the ports on the Multi-port Hub are installed by looking in your “Device Manager”. To get to “Device Manager” click on Start, select Set
ページ13に含まれる内容の要旨
Software Installation (continued) You’re done! You can now use the two serial ports on the Multi- port Hub as COM_A and COM_B (A and B can be any number from 2 to 10), and the parallel printer port as LPTUSB1. Take note of these port names when installing or attaching hardware to these ports. Go to page 17 for more information on installing a parallel printer. 11
ページ14に含まれる内容の要旨
Software Installation (continued) ® Software Installation – Windows 95 Prior to installing the Multi-port Hub drivers, you must ensure that the USB ports on your system are working properly. If you plug in the Multi-port Hub and nothing happens (with the power adapter), chances are your USB is not set up yet. You can try the following: ® • Upgrade to Windows 98 • Visit your computer manufacturer’s website for software and/or BIOS updates • Contact your computer manufacturer’s technical support
ページ15に含まれる内容の要旨
Software Installation (continued) ® You must then tell Windows where to get the drivers. Insert the CD-ROM in your CD-ROM drive, and click on “Other Locations…”: 13
ページ16に含まれる内容の要旨
Software Installation (continued) In the space provided, type in “d:\serial\win95” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on OK: Windows will read the CD-ROM and find the correct drivers. Click on Finish: 14
ページ17に含まれる内容の要旨
Software Installation (continued) ® Windows will display the following prompt. Click OK: In the space provided, type in “d:\serial\win95” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on OK: ® Next, Windows will detect another “Unknown Device”. This second “Unknown Device” is the parallel printer port of the Multi-port Hub. Click Next: 15
ページ18に含まれる内容の要旨
Software Installation (continued) You must then tell Windows where to find the drivers. Make sure the CD is in your CD-ROM drive, and click on “Other Locations…”: In the space provided, type “d:\parallel\win95” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on OK: 16
ページ19に含まれる内容の要旨
Installing a Parallel Printer ® Windows will read the CD-ROM and find the correct drivers. Click on Finish: ® Windows will display the following prompt. Click OK: 17
ページ20に含まれる内容の要旨
Software Installation (continued) In the space provided, type “d:\parallel\win95” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on OK: ® Once Windows has completed copying the files, it may prompt you again for the serial port drivers. Click OK: In the space provided, type “d:\serial\win95” (or substitute “d:” with the correct drive letter of your CD-ROM drive). Click on OK: 18
