ページ1に含まれる内容の要旨
OWNER'S MANUAL
________________
DS-RPC
DATA SWITCH/POWER CONTROL
FOR MODELS
DS2-RPC
DS4-RPC
Including the
DS71
DS71-MD2
DS74 &
DS73
Modules
BayTech Manual Publication #U140A124-01
August 1998
ページ2に含まれる内容の要旨
Copyright 1998 by Bay Technical Associates, Inc. BayTech, Telplex, LaserShare, Print Master and TRAN-X are registered trademarks of Bay Technical Associates, Inc. IBM, IBM PC, IBM PC/AT, IBM PC/XT are products and registered trademarks of International Business Machines Corporation. Hewlett-Packard LaserJet is a product and registered trademark of the Hewlett-Packard Company. PROCOMM PLUS is a product and registered trademark of Datastorm Technologies, Inc. â â Windows 95 is a product and regi
ページ3に含まれる内容の要旨
DS-RPC OWNER’S MANUAL ABOUT THIS OWNER’S MANUAL __________________________________________________________________________________________ ABOUT THIS OWNER’S MANUAL This document provides information required for installing and operating your Bay Tech equipment. It should allow the user to connect, power up, and access an applications menu where peripheral equipment can be controlled. We recommend reading this manual carefully, while placing special emphasis on correct cabling and configuration
ページ4に含まれる内容の要旨
DS-RPC OWNER’S MANUAL ABOUT THIS OWNER’S MANUAL __________________________________________________________________________________________ The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The in
ページ5に含まれる内容の要旨
DS-RPC OWNER’S MANUAL TABLE OF CONTENTS __________________________________________________________________________________________ ABOUT THIS OWNER’S MANUAL iii INTRODUCTION TO THE DS-RPC 1 PROGRAMMABLE FEATURES OF THE DS MODULES 3 DS-RPC QUICK START 6 EIA-232 SERIAL CONNECTION 6 OPERATION 6 DS-RPC CONFIGURATION 8 INSTALLATION 10 UNPACKING 10 PREPARING THE INSTALLATION SITE 11 POWER 11 POWER ON/OFF STATE 12 POWER UP SEQUENCE 12 CIRCUIT BREAKER 12 CABLING 13 RJ-45 CABLES AND ADAPTERS 13 MODEM CON
ページ6に含まれる内容の要旨
DS-RPC OWNER’S MANUAL TABLE OF CONTENTS __________________________________________________________________________________________ DS71-MD2 31 PORT DEVICE NAME 34 PORT SELECT CODE 35 ATTENTION CHARACTER 36 DISCONNECT TIME GUARD 37 CONNECT PORT ID ECHO 38 LOGIN SETUP 39 HEADER 39 PASSWORD 40 MENU 41 AUTO CONNECT PORT 42 DCD LOGON/LOGOFF (DS71 ONLY) 44 LOCAL MODEM SETUP (DS71-MD2 ONLY) 45 RINGS TO ANSWER 46 MODEM TO MODEM XON/XOFF 46 CONNECTIVITY TIMEOUT 47 ESCAPE CHARACTER 48 UNIT ID 49 I/O MODUL
ページ7に含まれる内容の要旨
DS-RPC OWNER’S MANUAL TABLE OF CONTENTS __________________________________________________________________________________________ TECHNICAL SUPPORT 69 EQUIPMENT SETUP 70 REPACKAGING, SHIPPING AND RETURNING TO THE FACTORY 71 FCC RADIO FREQUENCY INTERFACE STATEMENT 72 APPENDIX A – SPECIFICATIONS 74 APPENDIX B – MODEM COMMANDS 76 APPENDIX C – WINDOWS 95 TUTORIAL 78 APPENDIX D – DRAWINGS 81 APPENDIX E – ASCII CHARACTER DEFINITION 85 INDEX 86 vii
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INTRODUCTION TO THE DS-RPC __________________________________________________________________________________________ INTRODUCTION TO THE DS-RPC BayTech’s DS-RPC provides a single dialup or EIA-232 gateway to multiple EIA-232 devices. Used for accessing remote equipment or simply switching between multiple ports, the DS-RPC provides a full duplex connection between the host and up to 12 peripherals. In a typical application, the host module connects to a local or remote co
ページ10に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INTRODUCTION TO THE DS-RPC __________________________________________________________________________________________ Port selection is accomplished two different ways. (1) Use a simple menu-driven selection sequence or (2) send an ASCII character string to select a port. The DS-RPC also has four individual relay controlled, 115 VAC power receptacles. Each receptacle is controlled by sending simple commands from a local or remote location. The DS2-RPC base unit consists o
ページ11に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INTRODUCTION TO THE DS-RPC __________________________________________________________________________________________ PROGRAMMABLE FEATURES OF THE DS MODULES Highlighted features indicate items most often programmed FEATURE DESCRIPTION ACTION PAGE NO. DS71 or DS71-MD2 HOST MODULE Serial Port Sets serial port speed of the DS71 and Enter baud rate, data bits, 28 DS71-MD2 Default = 9600, 8, 1, N, stop bits, parity, and Configuration Xon/Xoff Disabled Xon/Xoff Uniquely identi
ページ12に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INTRODUCTION TO THE DS-RPC __________________________________________________________________________________________ PROGRAMMABLE FEATURES OF THE DS MODULES (con’t) FEATURE DESCRIPTION ACTION PAGE NO. DS71-MD2 HOST MODULE The number of times the modem rings Enter number of rings to 45 Rings to before it automatically answers. auto answer Answer(*) Default = 2 rings ASCII character used to stop or start Enable/ Disable Modem to 46 Modem to transmission of data. Modem Mode
ページ13に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INTRODUCTION TO THE DS-RPC __________________________________________________________________________________________ PROGRAMMABLE FEATURES OF THE DS MODULES (con’t) FEATURE DESCRIPTION ACTION PAGE NO. DS73TP N ETWORK MODULE IP Address for the DS73TP to access the Enter the IP Address in 54 Module IP network. Default = 0.0.0.0 dotted decimal format 0.0.0.0 Address IP Address for the network to access the Enter the IP Address in 55 Dial-in IP DS73TP. Default = 0.0.0.0 dott
ページ14に含まれる内容の要旨
DS-RPC OWNER’S MANUAL QUICK START __________________________________________________________________________________________ DS-RPC QUICK START This section, “Quick Start,” describes the basic steps required to set up and configure your DS-RPC. If you need to acquaint yourself further with setup, configuration, and operations, see “Detailed Operations and Configuration” beginning on page 18. EIA-232 SERIAL CONNECTION Using the 9FRJ45PC-4 adapter and the RJ08X007 (8 pin crossed) cable, connect
ページ15に含まれる内容の要旨
DS-RPC OWNER’S MANUAL QUICK START __________________________________________________________________________________________ Or this menu if the DS71-MD2 is used: Data Switch Series - F.0.13 Bay Technical Associates Unit ID: DS71-MD2 Port Select Code: $BT Attention Character: ; Use the “Attention Character” to display the remainder of the menu. Device A (2,1)...............1 Device B (2,2)...............2 Device C (2,3)...............3 Device D
ページ16に含まれる内容の要旨
DS-RPC OWNER’S MANUAL QUICK START __________________________________________________________________________________________ Accessing RPC Menu Select the RPC module. The following status menu appears: DS-RPC Series (C) 1997 by BayTech Rev. F0.04 Circuit Breaker : On 1) . . . OUTLET 1 : Off 2) . . . OUTLET 2 : Off 3) . . . OUTLET 3 : Off 4) . . . OUTLET 4 : Off RPC > If the status menu fails to appear, ensure the correct cables and adapters are being used and that they are c
ページ17に含まれる内容の要旨
DS-RPC OWNER’S MANUAL QUICK START __________________________________________________________________________________________ To configure a module, enter the number associated with it followed by . For detailed configuration of each module refer to: DS71 or DS71-MD2 page 26 DS74 page 51 DS73 page 53 RPC page 64 9
ページ18に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INSTALLATION __________________________________________________________________________________________ INSTALLATION UNPACKING Compare the unit and serial number of the equipment you received to the packing slip located on the outside of the box. Log this information on the sheet on page 70. Inspect equipment carefully for damage that may have occurred in shipment. If there is damage to the equipment or if materials are missing, contact BayTech customer service at 228-467-
ページ19に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INSTALLATION __________________________________________________________________________________________ PREPARING THE INSTALLATION SITE The installation area should be clean and free of extreme temperatures and humidity. Allow sufficient space behind the unit for cabling. POWER CAUTION: This unit is intended for indoor use only. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil the power cord when in use. Do not use extensi
ページ20に含まれる内容の要旨
DS-RPC OWNER’S MANUAL INSTALLATION __________________________________________________________________________________________ CAUTION: For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be incorporated in the fixed wiring. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and easily accessible. Applying power illuminates a green LED on the front panel of the DS- RPC. When the power switch is off, devices connected to the unit are not
