ページ1に含まれる内容の要旨
Rack Gigabit Switch Layer 2
24 ports 10/100Mbps Ethernet Switch
with 2 ports
1000BASE-T or 1000BASE-SX
User’s Guide
ページ2に含まれる内容の要旨
The Atlantis Land logo is a registered trademark of Atlants Land SpA. All other names mentioned mat be trademarks or registered trademarks of their respective owners. Subject to change without notice. No liability for technical errors and/or omissions. FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer
ページ3に含まれる内容の要旨
TABLE OF CONTENTS ABOUT THIS GUIDE ................................................... II TERMS/USAGE ................................................................. II INTRODUCTION ........................................................... 1 FAST ETHERNET TECHNOLOGY........................................ 1 GIGABIT ETHERNET TECHNOLOGY .................................. 1 SWITCHING TECHNOLOGY ............................................... 3 FEATURES..................................
ページ4に含まれる内容の要旨
ABOUT THIS GUIDE Congratulations on your purchase of the Management/Smart Gigabit & Fast Ethernet Switch (2×1000BASE plus 24×10/100BASE ports). In this guide, you will find about the following four models: 1. 2×1000BASE-T plus 24×10/100BASE-TX Gigabit Switch 2. 2×1000BASE-SX plus 24×10/100BASE-TX Gigabit Switch These four are designed to deliver full scalability of 10/100/1000Mbps, providing a simple solution to today’s complicated networking environment. Terms/U
ページ5に含まれる内容の要旨
INTRODUCTION This chapter describes the features of the Switch and some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. A number of high-speed LAN technologies have been proposed to provide greater bandwidth and improve client/server response times. Among them, 100BASE-T (
ページ6に含まれる内容の要旨
increase in theoretical throughput over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade without wasting a company’s existing investment in hardware, software, and trained personnel. The increased speed and extra bandwidth offered by Gigabit Ethernet are essential to coping with the network bottlenecks that frequently develop as compute
ページ7に含まれる内容の要旨
Switching Technology Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments. Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area
ページ8に含まれる内容の要旨
Features 24×10/100Mbps Auto-negotiation Ethernet ports and 2×10/100/1000Mbps Auto-negotiation Copper Gigabit Ethernet ports or 2×1000BASE-SX Fiber Gigabit Ethernet ports Auto MDI-X for all TX ports Full/half duplex transfer mode for each port Wire speed reception and transmission Store-and-Forward switching method Integrated address Look-Up Engine, supports 32K MAC addresses Supports 2Mbytes RAM for data buffering Supports port base VLAN / Trunking Supports IEEE 802.1p QoS
ページ9に含まれる内容の要旨
UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for the Switch. To avoid causing any damage to the Switch, we recommend that you read this chapter carefully before starting installation. Unpacking Open the shipping carton of the Switch and carefully unpack the items inside. The carton should contain the following items: The Smart Gigabit Ethernet Switch One AC power cord, suitable for your area’s electrical power connections Four rubber pa
ページ10に含まれる内容の要旨
Installation The site where you place the Switch may greatly affect its performance. When installing, take the following into your consideration: Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. Leave at least 10cm of space at the front and rear of the Switch for ventilation. Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipme
ページ11に含まれる内容の要旨
Rack Mounting The Switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipments. Attach the mounting brackets to both sides of the Switch (one at each side), and secure them with the provided screws. Then, use screws provided with the equipment rack to mount the Switch in the rack. 7
ページ12に含まれる内容の要旨
IDENTIFYING EXTERNAL COMPONENTS This chapter identifies all the major external components of the Switch. Both the front and rear panels are shown below, with a description of each panel features. Front Panel POWER FAN FAULT CONSOLE MG M 2 ×1000BASE-T plus 24×10/100BASE-TX Gigabit Switch POWER FAN FAULT CONSOLE MG M 2 ×1000BASE-SX plus 24×10/100BASE-TX Gigabit Switch LED Indicators Refer to the next chapter Understanding LED Indicators for detailed information on the meaning
ページ13に含まれる内容の要旨
PORT 25 & PORT 26 1000BASE-T Twisted Pair Ports (RJ-45) or 1000BASE-SX Fiber-Optic Ports (SC) - These two RJ-45 ports are auto MDI-X ports: The Switch is equipped with two Gigabit twisted pair ports, the ports will auto negotiate 10/100/1000Mbps. - The Switch is equipped with two Gigabit fiber-optic ports, the SC ports can connect to fiber networks on the other end with the same connector. CONSOLE PORT Attach a console cable to this console port at the left side of the front
ページ14に含まれる内容の要旨
UNDERSTANDING LED INDICATORS The front panel LEDs provide instant status feedback, and, helps monitor and troubleshoot when needed. PWR Power Indicator (green) On : When the green light is on, the Switch is receiving power. Off : Power cut off or improper connection. FAN FAULT Fan Indicator (Amber) On : Lights amber when the fan fails to work. Off : The fan is running normally. CONSOLE Console Indicator (green) On : Lights green when the console is logged in. Blinking : Bl
ページ15に含まれる内容の要旨
POWER FAN FAULT CONSOLE MGM Ports 1~24 Status LEDs LINK/ACT Link/Activity (green; amber) On : When the green light is on, the respective port is (Green) connected to a 100Mbps Fast Ethernet network. Blinking : When the green light is blinking, the port is transmitting (Green) or receiving data on the 100Mbps network. On : When the amber light is on, the respective port is (Amber) connected to a 10Mbps Ethernet network. Blinking : When the amber light is blinking, the port is transm
ページ16に含まれる内容の要旨
Port 25 & Port 26 Status LEDs 1000BASE-T 1000M LINK/ACT Link/Activity (green) On : When the green light is on, the respective port is connected to a Gigabit Ethernet network. Blinking : When the green light is blinking, the port is transmitting or receiving data on the 1000Mbps network. Off : No link activity. 100M LINK/ACT Link/Activity (green) On : When the green light is on, the respective port is connected to a Fast Ethernet network. Blinking : When the green light is bl
ページ17に含まれる内容の要旨
FDX/COL Collision/Full Duplex (green) On : When the green light is on, the respective port is in full duplex (FDX) mode. Blinking : Collision occurs. Off : When the green light is off, the respective port is in half duplex mode. 1000BASE-SX LINK/ACT Link/Activity (green) On : When the green light is on, the respective port is connected to a Gigabit Ethernet network. Blinking : When the green light is blinking, the port is transmitting or receiving data on the 1000Mbps netwo
ページ18に含まれる内容の要旨
CONNECTING THE SWITCH Referring to the cable specification below, use appropriate cables that meet your speed and cabling requirements when connecting the Switch to your network. The LAN card capabilities play an important role. If any status LED indicator is not shining after making a proper connection, check the PC LAN card, the cable, the Switch conditions and connections. Connecting Step-by-Step First, ensure the power of the switch and end devices is turned off. Step 1: Cons
ページ19に含まれる内容の要旨
Cable Specification Speed Connector Port Cable Max. Speed Distance Half/Full Duplex 10BASE-T RJ-45 10/20 Mbps 2-pair UTP/STP 100 m Cat. 3, 4, 5 100BASE-TX RJ-45 100/200 2-pair UTP/STP 100 m Mbps Cat. 5 1000BASE-T RJ-45 1000/2000 4-pair UTP/STP 100 m Mbps Cat. 5 (Cat. 5E is recommended) 1000BASE-SX SC 1000/2000 62.5/125µm 220 m Mbps multi-mode fiber (*Wavelength of 850nm) SC 1000/2000 50/125µm multi- 550 m Mbps mode fiber 16
ページ20に含まれる内容の要旨
CONFIGURING THE SWITCH This chapter explains how to configure the Switch to enable its smart functions. Port Speed & Duplex Mode By default, the Switch determines the transmission mode by auto- negotiation for any new twisted-pair or fiber connection after attaching the proper cable to a specific port. For 10/100/1000Mbps RJ-45 ports, if the attached device does not support auto-negotiation or has auto-negotiation disabled, an auto- sensing process is initiated to select speed (10M
