ページ1に含まれる内容の要旨
x600 Series
Layer 3 Gigabit
Ethernet Switches
x600-24Ts
x600-24Ts/XP
x600-48Ts
x600-48Ts/XP
◆
Installation Guide
613-001065 Rev. A
ページ2に含まれる内容の要旨
Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other informa
ページ3に含まれる内容の要旨
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy a
ページ4に含まれる内容の要旨
Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a document entitled Translated Safety Statements for the x600 Series Layer 3 Gigabit Ethernet Switches (613- 000990). 4
ページ5に含まれる内容の要旨
Contents Preface .............................................................................................................................................................. 7 Product Documentation ...................................................................................................................................... 8 Starting a Management Session ........................................................................................................................ 9 Safety Sym
ページ6に含まれる内容の要旨
Contents Unpacking a Switch ..........................................................................................................................................38 Installing the Power Cord Retaining Clip ..........................................................................................................39 Installing the Switches in an Equipment Rack ..................................................................................................40 Resetting the Switch ..............
ページ7に含まれる内容の要旨
Preface This guide contains the installation instructions for the x600 Series Layer 3 Gigabit Ethernet Switches. This preface contains the following sections: “Product Documentation” on page 8 “Starting a Management Session” on page 9 “Safety Symbols Used in this Document” on page 10 “Where to Find Web-based Guides” on page 11 “Contacting Allied Telesis” on page 12 7
ページ8に含まれる内容の要旨
Preface Product Documentation For overview information about the software features of the AlliedWare TM Plus Operating System Software which runs on the x600 Series Switches, refer to: TM AlliedWare Plus Operating System Software Reference Guide 8
ページ9に含まれる内容の要旨
x600 Layer 3 Gigabit Ethernet Switch Installation Guide Starting a Management Session For instructions that describe how to start a local management session on an x600 switch, refer to the “Starting a Local Management Session” on TM page 53. For information that describes how to log onto the AlliedPlus TM Operating System Software, see the AlliedWare Plus Operating System Software Reference Guide. 9
ページ10に含まれる内容の要旨
Preface Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. Table 1. Safety Symbols Symbol Meaning Description Caution Performing or omitting a specific action may result in equipment damage or loss of data. Warning Performing or omitting a specific action may result in electrical shock. 10
ページ11に含まれる内容の要旨
x600 Layer 3 Gigabit Ethernet Switch Installation Guide Where to Find Web-based Guides The installation and user guides for all Allied Telesis products are available in portable document format (PDF) on our web site at www.alliedtelesis.com. You can view the documents online or download them onto a local workstation or server. 11
ページ12に含まれる内容の要旨
Preface Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base: www.alliedtelesis.com/support/kb.aspx. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions. Email and For Technical Support via email or telephone, refer t
ページ13に含まれる内容の要旨
Chapter 1 Overview This chapter contains the following sections: “Introduction” on page 14 “Switch Descriptions” on page 15 “10/100/1000Base-T Twisted Pair Ports” on page 19 “SFP Transceiver Slots” on page 21 “XFP Transceiver Slots” on page 22 “Redundant Twisted Pair Ports” on page 23 “SD Card Slot” on page 24 “Port LEDs” on page 25 “System LEDs” on page 27 “Stack LEDs” on page 28 “Terminal Port” on page 30 “Secure Digital LEDs” on page 29 “AT-RPS3204 Redundant Power Supply” on pag
ページ14に含まれる内容の要旨
Chapter 1: Overview Introduction The x600 Series Switches are managed Gigabit Ethernet switches that acts as standalone units. There are four Basic Layer 3 switches in the series: x600-24Ts Switch x600-24Ts/XP Switch x600-48Ts Switch x600-48Ts/XP Switch The x600-24Ts and the x600-24Ts/XP switches both have 24 10/100/1000Base-T ports. The x600-48Ts and the x600-48Ts/XP switches both have 44 10/100/1000 Base-T ports. All four switches have four SFP transceiver slots, an Secure Digital (SD)
ページ15に含まれる内容の要旨
x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide Switch Descriptions The following sections describe the x600-24Ts, x600-24Ts/XP, x600-48Ts, x600-48Ts/XP Series Layer 3 Gigabit Ethernet Switches. x600-24Ts Switch The x600-24Ts switch has the following hardware features: 24 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management One SD slot supporting 512KB and 1G
ページ16に含まれる内容の要旨
Chapter 1: Overview x600-24Ts/XP The x600-24Ts/XP switch has the following hardware features: Switch 24 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management One SD slot supporting 512KB and 1GB SD cards Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Expan
ページ17に含まれる内容の要旨
x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide x600-48Ts Switch The x600-48Ts switch has the following hardware features: 44 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management One SD slot supporting 512KB and 1GB SD cards Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Expansion slot for the AT-StackXG Stacking M
ページ18に含まれる内容の要旨
Chapter 1: Overview x600-48Ts/XP The x600-48Ts/XP switch has the following hardware features: Switch 44 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management One SD slot supporting 512KB and 1GB SD cards Status LEDs for the ports, transceiver slots, and system Redundant power supply connector AT-LB
ページ19に含まれる内容の要旨
x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide 10/100/1000Base-T Twisted Pair Ports This section describes the twisted pair ports on the switches. Connector Type The ports are 8-pin RJ-45 connectors that use four pins at 10 or 100 Mbps and all eight pins at 1000 Mbps. For the pin assignments, refer to “RJ-45 Twisted Pair Port Pinouts” on page 67. Speed A port’s speed can be 10, 100, or 1000 Mbps. The speed can be set automatically through Auto-Negotiation, the default settin
ページ20に含まれる内容の要旨
Chapter 1: Overview Cable Type The cabling requirements for a 10/100/1000Base-T port are: For 10 Mbps operation: Standard TIA/EIA 568-B-compliant Category 3 or better shielded or unshielded cabling with 100 ohm impedance and a frequency of 16 MHz. For 100 Mbps operation: Standard TIA/EIA 568-A-compliant Category 5 or TIA/EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling with 100 ohm impedance and a frequency of 100 MHz. For 1000 Mbps operation: Standard TIA/
