ページ19に含まれる内容の要旨
Chapter 1 Overview This chapter describes the Layer 3+ SwitchBlade x8106 Chassis Switch in the following sections: “Introduction” on page 20 “AT-SBx8106 Chassis” on page 23 “AT-SBx81GT24 Line Card” on page 27 “AT-SBx81GT40 Line Card” on page 28 “AT-SBx81GP24 PoE Line Card” on page 29 “AT-SBx81GS24a SFP Line Card” on page 30 “AT-SBx81XS6 SFP+ Line Card” on page 31 “10/100/1000Base-T Twisted Pair Ports” on page 32 “Power over Ethernet on the AT-SBx81GP24 Line Card” on page 35
ページ20に含まれる内容の要旨
Chapter 1: Overview Introduction The SwitchBlade x8106 product is a modular Layer 3+ Ethernet switch. The main components are the AT-SBx8106 Chassis, Ethernet line cards, a controller card. system power supplies, Power over Ethernet Plus (PoE+) power supply, and fan module. The AT-SBx8106 Chassis is shown in Figure 1. Slots for four Ethernet line cards, two controller cards, two system power supplies, and two PoE+ power supplies. Figure 1. AT-SBx8106 Chassis The Ethernet line cards and co
ページ1に含まれる内容の要旨
SwitchBlade x8106
Layer 3+ Chassis Switch
AT-SBx8106 Chassis
AT-SBx81GT24 Line Card
AT-SBx81GT40 Line Card
AT-SBx81GP24 PoE Line Card
AT-SBx81GS24a SFP Line Card
AT-SBx81XS6 SFP+ Line Card
AT-SBx81CFC400 Controller Fabric Card
AT-SBxPWRSYS1 AC System Power Supply
AT-SBxPWRSYS1 DC System Power Supply
AT-SBxPWRPOE1 PoE Power Supply
AT-SBxFAN06 Module
Installation Guide
613-001835 Rev. A
ページ2に含まれる内容の要旨
Copyright 2013 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis, AlliedWare Plus, and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specificati
ページ3に含まれる内容の要旨
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy a
ページ4に含まれる内容の要旨
SwitchBlade x8106 Chassis Switch Installation Guide Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” on our web site at http://www.alliedtelesis.com/support. 4
ページ5に含まれる内容の要旨
Contents Preface ............................................................................................................................................................15 Safety Symbols Used in this Document ...........................................................................................................16 Contacting Allied Telesis ..................................................................................................................................17 Chapter 1: Overvie
ページ6に含まれる内容の要旨
Contents AT-SBxPWRSYS1 DC Power Supply.............................................................................................................. 57 LEDs.......................................................................................................................................................... 58 AT-SBxFAN06 Module..................................................................................................................................... 59 LED............................
ページ7に含まれる内容の要旨
SwitchBlade x8106 Chassis Switch Installation Guide Monitoring the Initialization Process ...............................................................................................................177 Using the LEDs to Monitor the Initialization Process ...............................................................................177 Using the Console Port to Monitor the Initialization Process ...................................................................177 Chapter 8: Verifying the Ha
ページ8に含まれる内容の要旨
Contents 8
ページ9に含まれる内容の要旨
Figures Figure 1: AT-SBx8106 Chassis ........................................................................................................................................... 20 Figure 2: Ethernet Line Cards and Controller Card ............................................................................................................. 20 Figure 3: Ethernet Line Cards and Controller Card (Continued) ......................................................................................... 21 Fi
ページ10に含まれる内容の要旨
List of Figures Figure 50: Unlocking the Handle on the AT-SBxPWRSYS1 Power Supply ........................................................................ 94 Figure 51: Inserting the AT-SBxPWRSYS1 Power Supply.................................................................................................. 95 Figure 52: Lowering the Handle on the AT-SBxPWRSYS1 Power Supply.......................................................................... 96 Figure 53: Removing the Blank Slot Cover from P
ページ11に含まれる内容の要旨
SwitchBlade x8106 Chassis Switch Installation Guide Figure 110: Attaching the Bare Grounding Wire to the Grounding Post............................................................................ 156 Figure 111: Securing the Bare Grounding Wire to the Grounding Post............................................................................. 157 Figure 112: Power Wire Terminals .......................................................................................................................
ページ12に含まれる内容の要旨
List of Figures 12
ページ13に含まれる内容の要旨
Tables Table 1. Twisted Pair Cable for the AT-SBx81GT24 and AT-SBx81GT40 Line Cards ......................................................33 Table 2. Twisted Pair Cable for the AT-SBx81GP24 Line Card .........................................................................................34 Table 3. IEEE802.3af and IEEE802.3at Powered Device Classes ....................................................................................35 Table 4. Maximum Number of Powered Devices ..............
ページ14に含まれる内容の要旨
List of Tables 14
ページ15に含まれる内容の要旨
Preface This guide contains the hardware installation instructions for the Layer 3+ SwitchBlade x8106 Chassis Switch. The preface contains the following sections: “Safety Symbols Used in this Document” on page 16 “Contacting Allied Telesis” on page 17 Note This version of the installation guide applies to release 5.4.3 of the AlliedWare Plus™ Operating System for the SwitchBlade x8106 Chassis Switch. 15
ページ16に含まれる内容の要旨
Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Warning Laser warnings inform you that an eye or skin hazard exists due to the presence of a Class 1 laser device. Warning Fan warnings in
ページ17に含まれる内容の要旨
SwitchBlade x8106 Chassis Switch Installation Guide Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following services on this page: 24/7 Online Support — Enter our interactive support center to search for answers to your product questions in our knowledge database, to check support ticke
ページ18に含まれる内容の要旨
Preface 18
