ページ1に含まれる内容の要旨
CheetaHub Power-3008P/3016P
Quick Installation Guide
ページ2に含まれる内容の要旨
Quick Installation Guide CheetaHub Power-3008P/16P Fast Ethernet Dual-Speed Hubs with 8/16 10/100Mbps (RJ-45) Ports, and Internal Switch CheetaHub Power-3008P CheetaHub Power-3016P
ページ3に含まれる内容の要旨
Copyright © 1999 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation. Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice. Accton reserves the right to make revis
ページ4に含まれる内容の要旨
Contents Introduction 1 Installing the Hub 1 Package Contents 1 Description of Hardware 1 Mounting the Hub 2 Stacking Hubs on a Flat Surface 2 Mounting Hubs in a Rack 3 Connecting the Hub System 3 Making a Connection via an RJ-45 Station Port 3 Making a Connection via an MDI Daisy-Chain Port 4 Powering On the Hub 5 Verifying Port Status 5 Verifying System Operation 6 Applications 6 Product Specifications 7 Repeater Criteria 7 Internal Switching Criteria 8 Troubleshooting 8 Diagnosing Hub Indicat
ページ5に含まれる内容の要旨
ii
ページ6に含まれる内容の要旨
Quick Installation Guide Introduction The CheetaHub Power-3008P/16P provides 8 (16) RJ-45 ports that automatically adjust to the speed of the attached device (for 10Mbps Ethernet or 100Mbps Fast Ethernet connections). These dual-speed hubs contain two internal repeater buses – one for 10Mbps traffic and another for 100Mbps traffic. Traffic passing between attached devices that operate at the same speed is confined within the appropriate repeater bus. But when traffic must pass between 10 and
ページ7に含まれる内容の要旨
CheetaHub Power-3008P/3016P containing the destination node via a 2-port switch that connects the two repeater buses. By confining traffic to its respective collision domain, and only forwarding traffic to the other segment when required, the overall load on the network is significantly reduced. These hubs provide a friendly design that simplifies installation and network troubleshooting. The following figure shows the components of the EH3016P: Mounting the Hub These hubs can be placed direct
ページ8に含まれる内容の要旨
Quick Installation Guide 2. Place the first hub on a firm flat surface where you want to install the stack. 3. Repeat step 1 for each hub before stacking them. The rubber foot pads cushion the hub against shock/vibrations and provide space between each hub for ventilation. Mounting Hubs in a Rack Please comply with the following instructions to ensure that your hub is securely mounted in the rack. 1. Use a standard EIA 19-inch rack. 2. Use the brackets and screws supplied in the rack mounting k
ページ9に含まれる内容の要旨
CheetaHub Power-3008P/3016P 3. Connect one end of the cable to the RJ-45 port of the network interface card, and the other end to any available (MDI-X) station port on the hub. The RJ-45 ports support 10Mbps and 100Mbps Ethernet connections. When inserting an RJ-45 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. Using a hub in a stand-alone configuration, you can network up to 8 (16) end nodes. Do not plug a phone jack connector into any RJ-45 po
ページ10に含まれる内容の要旨
Quick Installation Guide cabling will be limited to 5 meters (16 feet). The only way to extend the inter- hub cabling, would therefore be to reduce the length of the cabling used to attach the end nodes to the hubs. Ethernet Switch - There are no formal restrictions on cascade length if a device is connected to a switch, which effectively breaks up the collision domain. When a collision domain is broken up by a device like a switch, cascade length is limited only by the time-out requirement
ページ11に含まれる内容の要旨
CheetaHub Power-3008P/3016P Port and Hub Status LEDs LEDs Condition Status Power Green Hub is receiving power. Link Yellow Indicates a valid 10BASE-T connection between port and attached device. Green Indicates a valid 100BASE-TX connection between port and attached device. Partition Yellow Port has been partitioned due to an abnormal condition. Col Flashing Indicates that a packet collision has been Yellow detected on the indicated segment. Act Flashing Indicates that the port is transmitting o
ページ12に含まれる内容の要旨
Quick Installation Guide Connecting to a Network Backbone - You can easily connect to a collapsed backbone switch via the RJ-45 MDI daisy-chain port on the front panel. Because a switch breaks up the collision domain, it can be used to connect multiple CheetaHubs. Product Specifications Repeater Criteria Access Method CSMA/CD, 10 Mbps or 100 Mbps Standards Conformance IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Communication Rate 10/100 Mbps on all RJ-45 ports Media Supported 10BASE-T - 100Ω C
ページ13に含まれる内容の要旨
CheetaHub Power-3008P/3016P Maximum Current 0.3A max. @ 110VAC, 0.1A max. @ 240VAC RMS RMS Temperature 0°C to 50°C (32 to 122°F) Standard Operating, -40~70°C (-40~158°F) Storage Humidity 5% to 95% (Noncondensing) Certification CE Mark Emissions FCC Class A, VCCI Class A, EN55022 (CISPR22) Class A Immunity IEC 1000-4-2/3/4/6 Safety CSA/NRTL (C22.2.950, UL 1950), TÜV/GS (EN60950) IEC60950 (CB Report) Internal Switching Criteria Network Bridging Function Filtering, forwarding and learning Switching
ページ14に含まれる内容の要旨
Quick Installation Guide Power and Cooling Problems If the Power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fan on back of the unit is unobstructed and running prior to shutdown. If you still cannot i
ページ15に含まれる内容の要旨
CheetaHub Power-3008P/3016P Assignment Assignment Pin (Station Ports) (Daisy-Chain Port) 1+I+ nput Receive Data Output Transmit Data 2-I- nput Receive Data Output Transmit Data 3+O+ utput Transmit Data Input Receive Data 6-O- utput Transmit Data Input Receive Data 4d ,5,7,8Nd ot Use Not Use Schematics for both straight and crossover twisted-pair cable are shown below. Straight-Through Crossover () Hub) () Adapter() Hub (Hub 1+ IRD+ 1+ OTD1+ IRD 1 IRD 2- IRD- 2- OTD2- IRD 2 IRD 3+ OTD+3+ IRD3+ OT
ページ16に含まれる内容の要旨
Quick Installation Guide VCCI Class A Compliance (Japan) BCIQ Class A Compliance (Taiwan) CE Mark Declaration of Conformance (for EMI and Safety - Europe) This is to certify that this product complies with ISO/IEC Guide 22 and EN45014. It conforms to the following specifications: EMC: EN55022(1988)/CISPR-22(1985) Class A IEC1000-4-2(1995) 4kV CD, 8kV AD IEC1000-4-3(1995) 3V/m IEC1000-4-4(1995) 1kV - (power line), 0.5kV - (signal line) IEC 1000-4-6(1995) 3Vrms This product complies with the requi
ページ17に含まれる内容の要旨
CheetaHub Power-3008P/3016P Voltage Cord Set Specifications 1t 20 Volts UL Listed/CSA Certified Cord Se Minimum 18 AWG; type SVT or SJT three conductor cord Maximum length of 15 feet Parallel blade, grounding type attachment plug rated 15A, 125V 2t 40 Volts UL Listed/CSA Certified Cord Se (d North America) Minimum 18 AWG; type SVT or SJT three conductor cor Maximum length of 15 feet Tandem blade, grounding type attachment plug rated 15A, 125V 240 Volts Cord Set with H05VV-F cord having three con
ページ18に含まれる内容の要旨
Quick Installation Guide 15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen Nennstrom bis 6A und einem Gerätegewicht größer 3kg ist eine Leitung nicht leichter als 2 H05VV-F, 3G, 0.75mm einzusetzen. Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for a period of three years from the date of purchase from Accton or it’s Authorized reseller. For the warranty to apply,
ページ19に含まれる内容の要旨
EH3008P EH3016P E0999-R02 150052-102
