ページ1に含まれる内容の要旨
User Manual
Rack LCD Console
AP5717, AP5717F, AP5717G,
AP5717J, AP5717R, AP5717UK
AP5719
ページ2に含まれる内容の要旨
This manual is available in English on the enclosed CD. Dieses Handbuch ist in Deutsch auf der beiliegenden CD-ROM verfügbar. Este manual está disponible en español en el CD-ROM adjunto. Ce manuel est disponible en français sur le CD-ROM ci-inclus. Questo manuale è disponibile in italiano nel CD-ROM allegato. 本マニュアルの日本語版は同梱の CD-R OM からご覧になれます。 Данное ру к о во дство на р у сск ом язык е имее т ся на пр илаг ае мо м компак т- д и ск е. . 您可以从包含的 CD 上获得本手册的中文版本。 동봉된 CD 안에 한국어 매뉴얼이 있습니다 .
ページ3に含まれる内容の要旨
American Power Conversion Legal Disclaimer The information presented in this manual is not warranted by the American Power Conversion Corpora- tion to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, American Power Conversion Corpo- ration assumes no liability for damages, violations of codes, improper installation, system failures, or any other problems that could arise based o
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Contents General Information........................................................ 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Symbols used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Taking Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ページ6に含まれる内容の要旨
Troubleshooting ............................................................ 14 Specifications ................................................................ 15 ii Rack LCD Console User Manual
ページ7に含まれる内容の要旨
General Information Overview The Rack LCD Console features an 17” or a 19” LCD panel, a full keyboard, and a touch pad in a rack- mountable sliding housing. The Rack LCD Console is intended for use with compatible target devices (a KVM switch or server). Symbols used in this manual Note the definitions for the icons here and be observant for them throughout this manual. They are intended to call attention to potential hazards and important information. Electrical Hazard: Indicates an electrica
ページ8に含まれる内容の要旨
Safety Read and adhere to the following important safety considerations when working with the Rack LCD Console. Note: 1. Read all of the instructions. Follow all warnings and instructions. ® 2. All work must be performed by American Power Conversion (APC ) authorized personnel only. Electrical Hazard: 1. If you are not sure if your power source is compatible with the device requirements, consult your power company. 2. The device is designed for use with IT power distribution systems with u
ページ9に含まれる内容の要旨
Taking Delivery Examine the components at the time of delivery to be sure all parts are present and in good working order. Anything missing or damaged must be reported immediately to the shipping firm and to APC. Inventory Description Quantity Easy installation rack 1 mounting installation kit Mounting screws 4 Custom communication cable 2 sets - USB cable, length 6 ft. (1) - PS2 cable, length 6 ft. (1) C13 - C14 power cord 1 NEMA 5 - 15 power cord 1 Firmware upgrade cable 1 USB cable 1 Rack LC
ページ10に含まれる内容の要旨
Components Front View MENU LCD POWER EXIT UPGRADE FW UPGRADE Stand by NUM CAPS SCROLL LOCK LOCK LOCK RESET 4 Rack LCD Console User Manual aem0351b
ページ11に含まれる内容の要旨
Item Number Component Description EXIT button 1. Pressing the EXIT button without opening the On Screen Display (OSD) initiates an auto adjustment which reconfigures all settings for the monitor to the optimum display values of the OSD. 2. While the OSD user interface is in use, press the EXIT button to exit the current menu and return to the previous menu or, press the EXIT button to leave an adjustment menu when the adjustment is complete. 3. From the Main Menu screen, pressing the EXIT
ページ12に含まれる内容の要旨
Rear View 1 PS/2 - USB CPU 0 POWER Item Number Component Description Power Socket Standard 3-prong AC power socket. Power Switch Standard ON/OFF rocker switch Custom Port for connecting the Rack LCD Console to the target device (KVM switch Communication Port or server) using one of the included custom communication cables (PS2 or USB). USB Port USB pass-through from the USB Port on the front of the Rack LCD Console. 6 Rack LCD Console User Manual aem0351a
ページ13に含まれる内容の要旨
Installation Brackets Caution: Use only the hardware provided to install the Rack LCD Console in the rack. 1. Attach the left and right mounting rails to the inside of the rack. The flange that supports the Rack LCD Console station will be to the inside. a. Screw the front flanges to the rack first. 2. Slide the bars with the rear flanges toward the rack until the flanges make contact with the rack then screw the rear flanges to the rack. 3. Slide the Rack LCD Console ( ) onto the suppo
ページ14に含まれる内容の要旨
4. Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the Rack LCD Console. Use the supplied M4 x 6 screws to attach the bars to the rear of the Rack LCD Console switch. Fully tighten these screws. 5. Slide the Rack LCD Console open and closed two or three times to be sure it is operating smoothly. 6. If the Rack LCD Console is moving properly in the brackets, fully tighten the screws inserted in step 3. 8 Rack LCD Console User Manual aem0348a
ページ15に含まれる内容の要旨
Rack LCD Console Installation Cable installation Connect the target device (KVM switch or server) to the custom communication port on the back of the Rack LCD Console using one of the two custom communication cables (PS2 or USB) that are included. Plug the keyboard, monitor, and mouse connectors to the ports on the target device (KVM switch or server). Note: The maximum distance between the Rack LCD Console and the target device (a KVM switch or server) is 32.8 feet (10m). Power On the Rack
ページ16に含まれる内容の要旨
Operation Basic Functions Opening the Rack LCD Console To access the console, slide the Rack LCD Console out of the rack and raise the cover. Slide Rail Caution: Do not lean your body weight on the Rack LCD Console. Do not place heavy objects on the Rack LCD Console. Do not use the Rack LCD Console as a shelf. Closing the Rack LCD Console Close the cover and slide the Rack LCD Console into the rack. Powering off and restarting Turn off the power to the Rack LCD using the rear panel power switch
ページ17に含まれる内容の要旨
Monitor settings Setting Explanation Brightness Adjust the brightness level of the screen. Contrast Adjust level of color difference between foreground and background colors. Phase Adjust the phase setting of the screen so that no dark horizontal bands are visible. Clock Adjust the clock setting of the screen so that no dark vertical bands are visible. H-Position Moves the display area left or right. V-Position Moves the display area up or down. Color Hue Adjusts the color quality of the display
ページ18に含まれる内容の要旨
Firmware Upgrade Mode Check www.apc.com regularly to find the latest information and firmware upgrade packages. Note: Do not connect the RJ-11 port marked “Upgrade” to a public telecommunication network. Start the upgrade To download the firmware upgrade package: 1. Turn off the power to the Rack LCD Console. 2. Slide the Firmware switch to RECOVER. 3. Turn on the power to the Rack LCD Console. Note: When the Rack LCD Console is in Firmware Upgrade Mode, the Num Lock, Caps Lock and Scroll L
ページ19に含まれる内容の要旨
Exit firmware upgrade mode 1. Slide the Firmware Upgrade Recovery Switch to the Normal position. 2. Remove the Firmware Upgrade cable from the Firmware Upgrade Port of the Rack LCD Console. 3. Turn the power to the Rack LCD Console OFF and then turn the power ON. Firmware upgrade recovery There are three conditions that call for firmware upgrade recovery: • If the Rack LCD Console’s firmware becomes corrupted and is unable to operate. • When a firmware upgrade is interrupted. • When a firmware
ページ20に含まれる内容の要旨
Troubleshooting Symptom Action There are ghost images on the external monitor The distance between the external console and the Rack LCD is too great. The maximum VGA cable distance should not exceed 20m and in some cases may need to be shorter. Replace the VGA cable with one of an appropriately short length. Some characters entered from the keyboard do not The keyboard layout setting for the port does not match the display correctly. keyboard you are using. On your switch, change the keyboa
