ページ1に含まれる内容の要旨
Front cover
User’s Manual
C Do not connect this device to a computer data or
telecommunications network
TP Receivers Family
HIgh Resolution Video, Composite Video, and Stereo Audio
Twisted Pair Cable Transmission Products
68-547-02 Rev. J
01 09
ページ2に含まれる内容の要旨
Precautions Safety Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypa
ページ3に含まれる内容の要旨
Precautions, cont’d 安全须知 • 中文 警告 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生
ページ4に含まれる内容の要旨
TP Receivers ii
ページ5に含まれる内容の要旨
Table of Contents Chapter One • Introduction .................................................. 1-1 About the TP Receivers ..................................................... 1-2 Features ..................................................................................... 1-3 TP R BNC A receiver .............................................................. 1-3 TP R BNC AV receiver ........................................................... 1-4 TP R 15HD A receiver ....................
ページ6に含まれる内容の要旨
Table of Contents, cont’d Appendix • Specifications, Accessories, and Part Numbers ............................................................................................. A-1 Specifications ......................................................................... A-2 Included Parts ........................................................................ A-6 Extron Accessories ............................................................... A-6 Cables/Adapters ..........................
ページ7に含まれる内容の要旨
TP Receivers Chapter One 1 Introduction About the TP Receivers Features
ページ8に含まれる内容の要旨
Introduction, cont’d Introduction About the TP Receivers The TP R BNC A, TP R BNC AV and TP R 15HD are Extron Twisted Pair (TP) receivers that receive transmissions of RGB video, component video, S-video, composite video, and stereo audio over Extron Enhanced Skew-Free™ A/V UTP cable or standard Category (CAT) 5 unshielded twisted pair (UTP), shielded twisted pair (STP), or foil shielded twisted pair (FTP) cable. Standard transmission distance is shown in the tables below. Minimum relia
ページ9に含まれる内容の要旨
The TP receivers only receive signals transmitted by Extron TP transmitters. This user manual documents installation, features, and operation of the TP receivers only. For information about the TP transmitters, refer to the TP Transmitters Family User’s Manual, TP T 15HD 45 and TP T A 45 Manual, or the VTT001/TR001 Transmitter and Receiver Manual, as applicable, which accompanies the transmitters. Features All Extron TP receivers provide the following features: Audio output — Provides
ページ10に含まれる内容の要旨
Introduction, cont’d TP R BNC AV receiver The TP R BNC AV receiver has the following features: Video output — Provides RGBHV, RGBS, or RGsB video on 5 BNC connectors, and composite video on 1 BNC connector. RJ-45 connector — Allows attachment to an Extron TP transmitter. One connector is for computer input, and one is for A/V input. Cable length compensation — Allows you to select whether to compensate for long cable runs automatically or manually. Mounting — Mounts in a rack with an Ex
ページ11に含まれる内容の要旨
TP R 15HD A receiver The TP R 15HD A receiver has the following features: Video output — Provides RGBHV, RGBS, and RGsB on a 15-pin HD connector. With an optional SY 15 HD-RGBHV cable, the receiver can output component video, S-video, or composite video. RJ-45 connector — Allows attachment to an Extron TP transmitter. Mounting — TM Mounts in an Extron VersaTools 1U Rack Shelf (part #60-190-20), VersaTools 1U Basic Rack Shelf (part #60-604-20), a standard Universal 1U Universal Rack
ページ12に含まれる内容の要旨
Introduction, cont’d This page intentionally left blank. TP Receivers • Introduction 1-6
ページ13に含まれる内容の要旨
TP Receivers Chapter Two 2 Installation and Operation Installation Overview Front Panel Controls and Indicators Troubleshooting
ページ14に含まれる内容の要旨
Installation and Operation Installation and Operation, cont’d Installation Overview To install and set up a TP receiver and the associated TP transmitter(s) for operation, perform the following steps: 1 Disconnect power from all of the equipment, including the video source(s) (such as computers or DVD players), the transmitter, the receiver, and the output display(s). For component, S-video, or composite video, ensure 2 the internal jumpers (TP R BNC A and TP R BNC AV) or external DIP sw
ページ15に含まれる内容の要旨
The following transmitters are compatible with the N TP R 15HD A, TP R BNC A and TP R BNC AV receivers: TP T 15HD 45, TP T A 45, TP T 15HD A, TP T 15HD AV, TP T 468 All TP transmitters include a 15V or 12V external N power supply. The transmitters (with the exception of the TP T 15HD 45 and TP T A 45) also receive power from the associated Extron TP receiver(s) (with the exception of the TP R 15HD A) via the TP cable. Extron recommends using the local power supply; however
ページ16に含まれる内容の要旨
Installation and Operation, cont’d Video jumpers The TP R BNC A and TP R BNC AV receivers can be configured to receive component video, S-video, or composite video. The receivers are factory configured for RGB video. To N receive any other type of video, reconfigure the jumpers. 1. Remove the three screws on each side and the two screws on top of the cover (figure 2-1). Remove 8 Screws Lift Cover Straight Up TP R BNC AV For TP R BNC AV Remove Top PC board Remove 5 (TP R BNC A) or 6 (TP R BN
ページ17に含まれる内容の要旨
5. Locate J3 on the RGB video printed circuit board. See figure 2-1. a. For RGB video, ensure that pin 2 is jumpered to pin 3. b. For any other video format, ensure that pin 1 is jumpered to pin 2. 6. Reinstall the video board, replace the cover, and reinstall the screws and BNC connector hex nuts. Video DIP switch The TP R 15HD A receiver can be configured to receive component video, S-video, or composite video. To ON configure the receiver for RGB video, set DIP switch 3 (C video) o
ページ18に含まれる内容の要旨
Installation and Operation, cont’d 1. Remove three screws on each side and one or two screws on top of the cover (figure 2-2). Remove 8 Screws Lift Cover Straight Up TP R BNC AV Remove 5 (TP R BNC A) or 6 (TP R BNC AV) BNC Hex Nuts J10 J11 Wire Pair Wire Pair 3&6* 7&8 J11 1 1 Wire Pair Wire Pair 3&6* 7&8 J10 1 1 AV board in TPR BNC AV * TPX Compatible Figure 2-2 — Audio jumper configuration 2. Using an Extron BNC extraction tool (part #100-096-01) or a 14 mm, deep well socket with thin walls,
ページ19に含まれる内容の要旨
Mounting the receiver UL guidelines for rack mounting The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of the TP Receivers in a rack: 1. Elevated operating ambient temperature — If the unit is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, install the equipment in an environment compatible with the maximum ambient temperature
ページ20に含まれる内容の要旨
RGB LEVEL PEAKING TP R 15HD A VIDEO MANUAL LEVEL PEAKING AUTO RGB RGB RGB MANUAL LEVEL PEAKING LEVEL PEAKING LEVEL PEAKING TP R 15HD A TP R 15HD A AUTO TP R BNC AV Installation and Operation, cont’d Rack mounting (TP R BNC A, TP R BNC AV, TP R 15HD A) TP R BNC A, TP R BNC AV, or TP R 15HD AV — For optional rack mounting, mount the receiver on a 9.5" deep 1U Universal Rack Shelf (Extron part #60-190-01) (figure 2-3). The TP R BNC A and TP R BNC AV mount on the left or right side of the rack.
