ページ1に含まれる内容の要旨
User Guide
SCALERS AND SIGNAL PROCESSORS
DVS 605
HDCP-Compliant Scaler
(with Seamless Switching)
DVS 605
DVS 605 AD
68-2110-01 Rev. B
05 13
ページ2に含まれる内容の要旨
Safety Instructions Safety Instructions • English Chinese Simplified （简体中文） 警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage 电压，有触电危险。 within the product’s enclosure that may present a risk of electric shock. 注意： 产品 上 的 这个标 志意在 提 示用户设备 随 附的用户手 册 中有 重要的操作和维护(维修）说明。 ATTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and maintenan
ページ3に含まれる内容の要旨
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Ope
ページ4に含まれる内容の要旨
Conventions Used in this Guide Notifications The following notifications are used in this guide: DANGER: A danger indicates a situation that will result in death or severe injury. WARNING: A warning indicates a situation that has the potential to result in death or severe injury. CAUTION: A caution indicates a situation that may result in minor injury. ATTENTION: Attention indicates a situation that may damage or destroy the product or associated equipment. NOTE: A note draws attention to
ページ5に含まれる内容の要旨
Contents Introduction............................................................ 1 SIS Communication and Control .................... 34 DVS 605 Series Description ................................ 1 Host to Scaler Communications ....................... 34 Licensed Third‑ party Software Used in the DVS Scaler‑ initiated Messages ............................. 34 605 ................................................................... 2 Copyright Information ................................... 34 K
ページ6に含まれる内容の要旨
Mounting ............................................................... 90 Mounting the DVS 605 ..................................... 90 Tabletop Placement ...................................... 90 UL Guidelines for Rack Mounted Devices .... 90 Rack Mounting ............................................. 91 Furniture Mounting........................................ 91 Warranty................................................................ 92 Contact Information ................................
ページ7に含まれる内容の要旨
Introduction This manual contains information about the Extron DVS 605 scalers with instructions for experienced installers on how to install, configure, and operate the equipment. In this manual the terms “DVS,” “digital video scaler,” and “scaler” are used interchangeably and refer to any DVS 605 model. DVS 605 Series Description The DVS 605 series of digital video scalers is comprised of: • DVS 605, standard model • DVS 605 A, with audio switching • DVS 605 D, with 3G/HD‑ SDI outp
ページ8に含まれる内容の要旨
Licensed Third-party Software Used in the DVS 605 The DVS 605 uses various licensed third‑ party software during operation. To view details about third‑ party packages and associated licensing, click the License Information button on the Unit Information page of the Default web pages (see the Unit Information Page on page 82). The DVS 605 License Information dialog box opens. To view a copy of a listed package license, in the dialog box, click the link in the License column for the relevan
ページ9に含まれる内容の要旨
Key Features Video Inputs • Three HDMI and two universal analog video inputs — The two universal 15‑ pin HD inputs automatically detect incoming RGB, HD component video, YUVi, S‑ video, or composite video signals. The DVS 605 allows for seamless switching between HDMI and analog video sources. • Auto input format detection — For the universal analog video inputs, the DVS 605 detects the incoming signal format, automatically reconfiguring the scaler to provide the appropriate decoding and
ページ10に含まれる内容の要旨
Audio • Audio switching — The DVS 605 A and DVS 605 AD feature audio switching for five analog stereo balanced or unbalanced inputs. • Output volume control — DVS 605 audio models provide master volume control. Fixed and variable line level outputs are available, and each output can be balanced or unbalanced. Stereo input signals can be output as dual mono. The DVS 605 audio models also include a S/PDIF digital audio output. • Audio input gain and attenuation — Gain or attenuation can be
ページ11に含まれる内容の要旨
• AFL - Accu-RATE Frame Lock — A patented technology exclusive to Extron that eliminates image tearing caused by frame rate conversion. • Image freeze control — A live image can be frozen using control via USB, RS‑ 232 serial, Ethernet, or IR control. • Auto-Image setup — When activated, the unit automatically detects the resolution of the incoming video signal and sets the total pixels, active pixels, and active lines, as well as the horizontal and vertical starting points. • Auto Inpu
ページ12に含まれる内容の要旨
• RS-232 control port — Using serial commands, the DVS 605 can be controlled and configured via the embedded web pages, or integrated into a control system. Extron products use the SIS ‑ Simple Instruction Set command protocol, a set of basic ASCII code commands that allow for quick and easy programming. • Front panel USB configuration port — Enables easy configuration without having to access the rear panel. • Contact closure ports — These can be used for external control of source swit
ページ13に含まれる内容の要旨
Rear Panel Connections This section describes how to connect cables to a DVS 605 scaler. Rear Panel Cabling The illustration below shows all the possible rear panel features of the audio (DVS 605 A and DVS 605 AD) and the non‑ audio (DVS 605 and DVS 605 D) models. 3 15 DVS 605 INPUT OUTPUTS REMOTE 1 5 AUX 3 1234 5 3G/HD - SDI GENLOCK CONTACT UNIVERSAL 2 HDMI RESET RS-232 IR 4 100-240 VAC ~ .7A MAX HDMI RGB/R-Y, Y, B-Y Tx Rx G G S 50/60Hz LAN 2 1 5 6 12 13 14 8 15 3 7 DVS 605 D INPUT OUTP
ページ14に含まれる内容の要旨
a Power input — Connect the standard IEC power cord from a 100 to 240 VAC, 50‑ 60 Hz power source into this connector. The front panel control and input selection buttons light in sequence during power‑ up. b Inputs 1 and 2 — Connect suitable inputs to these two universal analog input ports (15‑ pin HD [VGA] connectors) for auto‑ detection of RGB, HD component video, YUVi, S‑ video, or composite video signals. These universal analog input ports can be configured to accept RGB (RGBHV, RGBs
ページ15に含まれる内容の要旨
LR LR 5. While holding the connector securely against the lacing bracket, tighten the tie wrap, then remove any excess length. The LockIt bracket can also be used in a stacked formation, as shown below. Side Mounted Stacked Figure 2. LockIt Bracket Mounting Options d Audio inputs 1-5 (audio models only) — Connect audio sources to these 5‑ pole captive screw connectors. Wire the connector for line level, balanced or unbalanced, analog stereo as shown below. Tip Tip Ring Sleeve Sleeves Tip Ti
ページ16に含まれる内容の要旨
LR LR LR LR i Audio output (fixed, audio models only) — Connect audio output devices to this 5‑ pole, captive screw connector for line level, balanced or unbalanced, analog stereo. Wire the connectors as shown below. No Ground Here Tip Ring Tip Sleeves Sleeves Tip Tip Ring Do not tin the wires! No Ground Here Balanced Audio Output Unbalanced Audio Output Figure 4. Audio Output Connector Wiring j RCA audio output (S/PDIF, fixed, audio models only) — Plug in an S/PDIF audio output device into
ページ17に含まれる内容の要旨
n RS-232/IR port — For serial RS‑ 232 control, connect a host computer or control system to the 5‑ pole captive screw connector. This port is also a hard wired IR control for use with an external IR controller. The default RS‑ 232 protocol is 9600 baud, 1 stop bit, no parity, 8 data bits, no flow control. By default the IR port is disabled. When enbled, the IR port accepts 38 kHz to 1 MHz, modulated signals at TTL level (0‑ 5 V) o Remote contact closure port — For remote input selection o
ページ18に含まれる内容の要旨
Operation This section of the manual discusses the operation of a DVS 605 device. Topics covered include: • Front Panel Overview • Powering Up • The DVS 605 Menu System — Configuration and Adjustments • Front Panel Lockout (Executive Modes) • Window vs. Image Size Position — An Overview • Picture-in-Picture (PIP) Mode • Other DVS 605 Operating Features Front Panel Overview 3 DVS 605 DIGITAL VIDEO SCALER 1 2 3 AUTO MENU ADJUST EXTRON 4 5 PIP SWAP NEXT DVS 605 CONFIG 2 4 5 1 6 7 Figure 7.
ページ19に含まれる内容の要旨
Powering Up When applying power to the DVS 605, the unit undergoes a start‑ up self testing sequence (see image below) and then the LCD displays the default display cycle. Default Display Cycle When in use but not in any menu mode, the LCD screen defaults to cycling through the input/output configuration currently installed. The displayed content may vary, depending on the input video signal type. See figure 8 for a typical default display cycle. Figure 8. Typical Default Display Cycle The
ページ20に含まれる内容の要旨
Menu Overview After start‑ up, and when no adjustments are actively being made, the “default cycle” appears on the LCD. The screens cycle between the screen that shows the number and video format of the active input and the current output resolution. Pressing the Menu button once brings up the first of eight main (top level) menus, as shown below. Each successive press of the Menu button goes to the next main menu. Default Display Cycle Menu INPUT Menu Menu OUTPUT USER PICTURE Menu CONFIG 2
