ページ1に含まれる内容の要旨
RX-V1600
RX-V1600_U-cv.fm Page 1 Friday, August 26, 2005 4:34 PM
U
RX-V1600
AV Receiver
© 2005 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 773
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 10 Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the CAUTION product and to protect it from overheating, and these RISK OF ELECTRIC SHOCK openings must not be blocked or covered. The openings DO NOT OPEN should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS d) If the product does not operate normally by following 24 Outdoor Antenna Grounding – If an outside antenna or the operating instructions. Adjust only those controls cable system is connected to the product, be sure the antenna that are covered by the operating instructions as an or cable system is grounded so as to provide some improper adjustment of other controls may result in protection against voltage surges and built-up static charges. damage and will of
ページ4に含まれる内容の要旨
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual 15 When not planning to use this unit for long periods of time carefully. Keep it in a safe place for future reference. (i.e. vacation), disconnect the AC power plug from the wall outlet. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, 16 Install this unit near th
ページ5に含まれる内容の要旨
BASIC SOUND FIELD ADDITIONAL ADVANCED OPERATION PROGRAMS INFORMATION INTRODUCTION PREPARATION OPERATION CONTENTS INTRODUCTION SOUND FIELD PROGRAMS FEATURES............................................................. 2 EDITING SOUND FIELD PARAMETERS ......62 GETTING STARTED............................................ 3 What is a sound field? ............................................. 62 Changing parameter settings ................................... 62 Supplied accessories .................
ページ6に含まれる内容の要旨
FEATURES FEATURES Built-in 7-channel power amplifier HDMI (High-Definition Multimedia Interface) ◆ Minimum RMS Output Power ◆ HDMI interface for standard, enhanced or (0.04% THD, 20 Hz to 20 kHz, 8 Ω) high-definition video as well as multi-channel digital Front: 120 W + 120 W audio Center: 120 W ◆ Analog video to HDMI digital video up-conversion Surround: 120 W + 120 W (composite video ↔ S-video ↔ component video → Surround Back: 120 W + 120 W HDMI digital video) capability for monitor out S
ページ7に含まれる内容の要旨
INTRODUCTION k GETTING STARTED GETTING STARTED Supplied accessories Please check that you received all of the following parts. Remote control POWER POWER STANDBY POWER TV AV A XM AUDIO SEL SLEEP PHONO TUNER CD MULTI CH IN Zone 2/Zone 3 V-AUX CBL/SAT MD/TAPE CD-R remote control DTV VCR 1 DVR/VCR2 DVD XM POWER TUNER CD CD-R STANDBY SELECT 1 2 3 DTV CBL/SAT MD/TAPE PHONO AMP 4 5 6 ENT Batteries (x6) + + + SOURCE V-AUX VCR1 DVR/VCR2 DVD TV VOL CH VOLUME 7 8 9 (AAA, R03) 0 0 TV – – – TV MUTE TV INP
ページ8に含まれる内容の要旨
GETTING STARTED Installing batteries in the remote controls Notes Change all of the batteries if you notice conditions such as the operation range of the remote control decreases, the indicator does not flash, or its light or display window become dim. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and co
ページ9に含まれる内容の要旨
INTRODUCTION GETTING STARTED Handling the remote control The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation. PURE DIRECT VOLUME AUDIO MULTI CH PRESET/ TUNING TONE SELECT INPUT A/B/C/D/E PRESET/TUNING/CH TUNING FM/AM MEMORY MODE STRAIGHT CONTROL EDIT MAIN ZONE INPUT CATEGORY SEARCH MODE DISPLAY MAN'L/AUTO FM AUTO/MAN'L EFFECT SPEAKERS ZONE ON/OFF ZONE CONTROL PROGRAM MULTI ZONE A B ZON
ページ10に含まれる内容の要旨
CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS Front panel Note The XM Satellite Radio controls (SEARCH MODE, CATEGORY, PRESET/TUNING/CH l / h, MEMORY and DISPLAY) are only applicable to the U.S.A. model and are operational only when XM is selected as the input source. For details, see “Front panel functions” on page 53. 1 2 3 45 6 7 8 90AB C DE F PURE DIRECT VOLUME AUDIO MULTI CH TONE PRESET/ TUNING SELECT INPUT A/B/C/D/E PRESET/TUNING/CH TUNING FM/AM MEMORY MODE STRAIGHT CONTROL EDIT CATEGORY
ページ11に含まれる内容の要旨
INTRODUCTION CONTROLS AND FUNCTIONS 8 Front panel display I PHONES (SILENT CINEMA) jack Shows information about the operational status of this Outputs audio signals for private listening with unit. headphones. 9 PRESET/TUNING (EDIT) Notes Switches the function of PRESET/TUNING/CH l / h When you connect headphones, no signals are output at the between selecting preset station numbers and tuning when PRE OUT jacks or to the speakers. TUNER is selected as the input source (see pages 46 to
ページ12に含まれる内容の要旨
CONTROLS AND FUNCTIONS Remote control This section describes the function of each control on the 1 Infrared window remote control used to control this unit. Set AMP/ Outputs infrared control signals. Aim this window at the SOURCE/TV to AMP to operate this unit. To operate component you want to operate. other components, see “REMOTE CONTROL 2 Transmission indicator FEATURES” on page 92. Flashes while the remote control is sending infrared signals. Note The XM Satellite Radio controls (XM, XM
ページ13に含まれる内容の要旨
INTRODUCTION CONTROLS AND FUNCTIONS A STANDBY J PURE DIRECT Sets this unit, Zone 2 and Zone 3 to the standby mode (see Turns on or off the PURE DIRECT mode (see page 41). page 30). K SET MENU Enters or exits the SET MENU mode. Note L NIGHT This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position. Turns on or off the night listening modes (see page 41). B POWER M ON SCREEN Turns on this unit, Zone 2 and Zone 3 (see page 30). Selects the display m
ページ14に含まれる内容の要旨
k CONTROLS AND FUNCTIONS Zone 2/Zone 3 remote control This section describes the function of each control on the 1 Input selector buttons Zone 2/Zone 3 remote control used to control Zone 2 or Select the desired input source of Zone 2 or Zone 3 and Zone 3. change the control area. 2 PRESET +/– Note Selects the preset station number (1 to 8) when TUNER is The XM Satellite Radio controls (XM, DISPLAY, PRESET, selected as the input source or Zone 2 or Zone 3. ALL, CAT., numeric buttons, NUMBER,
ページ15に含まれる内容の要旨
INTRODUCTION CONTROLS AND FUNCTIONS Front panel display Note The XM indicator is only applicable to the U.S.A. model. 123 4 5 6 7 890A V-AUX DVR/VCR 2 VCR 1 CBL/SAT DTV DVD MD/TAPE CD-R CD PHONO TUNER XM STEREO TUNED DIGITAL AUTO MEMORY PL x YPAO HiFi DSP CS CS dB ZONE2 EX VOLUME MUTE ZONE3 SP 96/24 NIGHT A B L L C R DSD 96 SLEEP DISCRETE SILENT VIRTUAL LFE SL SB SR PCM MATRIX 24 CINEMA BCD E FG HI J KL M NO P 1 YPAO indicator A MEMORY indicator Lights up when the AUTO SETUP procedure is in Fl
ページ16に含まれる内容の要旨
CONTROLS AND FUNCTIONS K 96/24 indicator Lights up when a DTS 96/24 signal is input to this unit. L LFE indicator Lights up when the input signal contains an LFE signal. M Input channel and speaker indicators Input channel indicators Indicate the channel components of the current digital input signal. L L C R SL SB SR Presence and surround back speaker indicators Light up according to the number of presence and surround back speakers set for PRESENCE SP (see page 79) and SB L/R SP (see page
ページ17に含まれる内容の要旨
INTRODUCTION CONTROLS AND FUNCTIONS Rear panel 12 3 4 56 7 8 9 DIGITAL INPUT COMPONENT VIDEO VIDEO AUDIO AUDIO CONTROL OUT TUNER COAXIAL S VIDEO VIDEO R L R L Y PB PR +12V 15mA MAX. FM ANT GND AM ANT (PLAY) 75Ω DVD AC IN IN UNBAL. DVD 1 2 CD DVD DVR/ MD/TAPE REMOTE WRENCH VCR 2 DTV HOLDER SPEAKERS OPTICAL + – – + CD DTV IN R A L OUT (REC) CBL/ (PLAY) SAT IN CBL/ DVD OUT SAT CD-R FRONT CENTER + – – + – + B DTV IN RS-232C OUT (REC) MONITOR OUT VCR 1 GND IN 1 CBL/SAT OUT CD SPEAKER IMPEDANCE PRE
ページ18に含まれる内容の要旨
CONNECTIONS CONNECTIONS Surround speakers (SR and SL) Before connecting speakers The surround speakers are used for effect and surround sounds. Place these speakers behind your listening * The speaker layout below shows the standard ITU-R position, facing slightly inwards, about 1.8 m (6 ft) above speaker setting. You can use it to enjoy CINEMA DSP, the floor. multi-channel audio sources and THX. Surround back speakers (SBR and SBL) * The surround back speakers supplement the surround ITU-
ページ19に含まれる内容の要旨
PREPARATION CONNECTIONS ■ Di-pole speaker layout Connecting speakers Either di-pole or direct radiating speaker types can be used for THX surround. If you choose di-pole speakers, please Be sure to connect the left channel (L), right channel (R), place the surround and surround back speakers according “+” (red) and “–” (black) properly. If the connections are to the speaker layout below. faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is inc
ページ20に含まれる内容の要旨
CONNECTIONS 1 Remove approximately 10 mm (3/8 in) of 5 Tighten the knob to secure the wire using the insulation from each of the speaker cables. supplied speaker terminal wrench. Speaker terminal wrench 10 mm (3/8 in) 2 Twist the exposed wires of the cable together to prevent short circuits. Red: positive (+) Black: negative (–) 6 Hook the speaker terminal wrench onto WRENCH HOLDER on the rear panel of this unit when not in use. 3 Loosen the knob using the supplied speaker terminal wrench.
