ページ1に含まれる内容の要旨
T E C H N O L O G I E S
Owner’s Manual and
Installation Guide
LW1.1100D
LW1.1700D
LW1.2600D
ページ2に含まれる内容の要旨
CONGRATULATIONS! You now own a Limited Edition LIL’WONDER Amplifier, the product of an uncompromising design and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards. When properly installed, they will provide you with many
ページ3に含まれる内容の要旨
FEATURES Mono-Block Class D Amplifier Total Harmonic Distortion:0.5% Frequency Response: 15-150Hz Signal to Noise Ratio: 105dB Damping Factor: >250 Input Sensitivity 100mV - 8V 50-150Hz,12dB Low Pass Fiter 45Hz, 0-18dB Bass Boost 180° Phase Switch Midnight Black Finish w/ Brushed Accents Remote Gain Control Master/Slave Operation Pre-amp Outputs 3
ページ4に含まれる内容の要旨
SPECIFICATIONS Signal/Noise Ratio >105dB Frequency Response 15Hz-150Hz THD 0.50% LPF 50Hz -150Hz,12dB Input Voltage Range 11-16 Volts DC High Impedance RCA/LINE 30K Ohms Level Input Impedance POWER RATINGS & FUSE MODEL 4 ohm 2 ohm 1 ohm FUSE LW1.1100D 600W 900W 1100W 35A X 3 LW1.1700D 700W 1200W 1700W 40A X 4 LW1.2600D 1000W 1800W 2600W 250A DIMENSIONS Length Height MODEL Width LW1.1100D 390mm 205mm 60mm LW1.1700D 450mm 205mm 60mm LW1.2600D 580mm 205mm 60mm 4
ページ5に含まれる内容の要旨
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal. Protection Circuitry The amplifier pr
ページ6に含まれる内容の要旨
Electrical Wiring All LIL’WONDER Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections. Wire the amplifier directly to the car battery. Make sure there is circuit protection (Such as a fuse) on the positive power lead, with
ページ7に含まれる内容の要旨
PANEL LAYOUT LW1.1100D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave R R RIGHT VIEW BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES LW1.1700D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180 Mi
ページ8に含まれる内容の要旨
PANEL LAYOUT LW1.2600D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave R R RIGHT VIEW SPEAKER POWER CONNECTIONS Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D/LW1.2600D Low Level Inputs Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTEC
ページ9に含まれる内容の要旨
Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES LW1.1700D has four fuses here BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES LW1.1700D has four fuses here 9
ページ10に含まれる内容の要旨
Class D Monoblock Amplifier Installation Wiring LW1.2600D SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS 10
ページ11に含まれる内容の要旨
Bridging Two LW1.1100D/LW1.1700D/LW1.2600D Amplifiers Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION L 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V R Master Slave R R Power min Max Subsonic Low Pass Bass Line Out Line Input Input Filter Filter Boost PHASE Level L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Bridged Input Sensitivity
ページ12に含まれる内容の要旨
Bridging Two LW1.1100D/LW1.1700D Amplifiers BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES LW1.1700D has four fuses here BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES 12
ページ13に含まれる内容の要旨
Bridging Two LW1.2600D Amplifiers SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS 13
ページ14に含まれる内容の要旨
TROUBLE SHOOTING NO SOUND Is the LED lit? NO YES Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in. SOUND IS NOW IN SAME CHANNEL OPPOSITE CHANNEL Reverse RCA inputs Problem is in the speaker of speaker wire of the silent channel SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL
ページ15に含まれる内容の要旨
Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected. Only plug in or unplug RCA plugs with the amplifier off as Standard practice with all audio equipment.
