ページ1に含まれる内容の要旨
S1500 / S2000
POWER
AMPLIFIER
-20dB -20dB
OFF ON
-40dB -20dB CLIP PROTECTION POWER PROTECTION -40dB -20dB CLIP
-30dB -10dB -30dB -10dB
S2000
1000W X2 STEREO
CHANNEL 1 CHANNEL 2
-80dB 0dB -80dB 0dB SAMSON
-20dB -20dB
OFF ON
-40dB -20dB CLIP PROTECTION POWER PROTECTION -40dB -20dB CLIP
-30dB -10dB -30dB -10dB
S1500
750W X2 STEREO
CHANNEL 1 CHANNEL 2
-80dB 0dB -80dB 0dB SAMSON
OWNERS MANUAL
®
ページ2に含まれる内容の要旨
Table of Contents Introduction 1 S1500 / S2000 Features 2 Guided Tour 3 Front Panel 3 Rear Panel 4 Setting Up and Using Your S1500 / S2000 5 The S1500 / S2000 Protection Circuitry 6 Bridged and Parallel Modes 7 S1500 / S2000 Connections 8 Specifications 10 Produced by On The Right Wavelength for Samson Technologies Corp. Copyright 1999, Samson Technologies Corp. Printed October 1999 Samson Technologies Corp. 575 Underhill Blvd. P.O. Box 9031 Syosset, NY 11791-9031 Phone: 1-800-3-SAMSON
ページ3に含まれる内容の要旨
Introduction We know you don’t like reading owners manuals, but you’ve just purchased one of the finest sound reinforcement power amplifiers around, and we want to tell you about it! So, before you plug in, we’d like to suggest you take just a few moments out to scan these pages. We’ll make it as painless as possible, we promise—and, who knows, you might just pick up a tip or two. The Samson S1500 / S2000 is a three rack-space stereo power amplifier which is optimized for live sound venues, co
ページ4に含まれる内容の要旨
S1500 / S2000 Features The Samson S1500 / S2000 power amplifier utilizes the latest technology in professional power amplifier design. Here are some of its main features: • Power to spare - In the S1500, each channel delivers 750 watts of power into 4 ohms. In the S2000, each channel delivers 1000 watts of power into 4 ohms. • A Bridged mode links both channels, thus providing additional power (1500 watts into 8 ohms in the case of the S1500; 2000 watts into 8 ohms in the case of the S2000). •
ページ5に含まれる内容の要旨
Guided Tour - Front Panel 5 4 1 2 3 4 5 -20dB OFF ON -20dB -40dB -20dB CLIP PROTECTION POWER PROTECTION -40dB -20dB CLIP -30dB -30dB -10dB -10dB S2000 1000W X2 STEREO CHANNEL 2 CHANNEL 1 -80dB 0dB -80dB 0dB SAMSON 1: Power switch - Use this to power the S1500 / S2000 on or off. 2: Power LED - Lights whenever the S1500 / S2000 is powered on. 3: Protection LED - This goes on for approximately five seconds whenever the S1500 / S2000 is powered on and then turns off (you’ll hear a “click” when i
ページ6に含まれる内容の要旨
Guided Tour - Rear Panel 1 2 4 7 1 OUTPUT INPUT BRIDGED PUSH PUSH (8Ω ~16Ω ) PUSH TO RESET 25A/250V (4Ω ~8Ω ) (4Ω ~8Ω ) BALANCED BALANCED 0dBm 0dBm TIP=HOT 3=COLD TRS XLR RING=COLD 2=HOT BALANCED SLEEVE=GND BALANCED 1=GND ~AC INPUT 115V 60Hz, 1100W (4Ω ~8Ω ) (4Ω ~8Ω ) CH 2 CH 1 CH 2 CH 1 BRIDGED PARALLEL STEREO 8 3 5 6 1: Fan - This variable-speed fan provides vital cooling to your S1500 / S2000 (the hotter the amp gets, the faster the fan blows!). Make sure that both the front and rear pa
ページ7に含まれる内容の要旨
Setting Up and Using Your S1500 / S2000 Setting up your S1500 / S2000 is a simple procedure which takes only a few minutes: 1. Remove all packing materials (save them in case of need for future service) and decide where the amplifier is to be physically placed—it can be used free-standing or mounted in a standard 19" rack, requiring only three rack spaces. When installed, make sure that both the front and rear panels are unobstructed and that there is good ventilation around the entire unit (w
ページ8に含まれる内容の要旨
The S1500 / S2000 Protection Circuitry As noted in the “Guided Tour” section of this manual, the S1500 / S2000 front- panel Protection LED indicates the activity of the relay speaker connection PROTECTION circuitry. When the Protection LED is lit, this circuitry is active, and all connected speakers are muted (provided with 0 volts DC), thus protecting them and preventing any audible “thump” from occurring. The following conditions will cause the Protection LED to go on: • Initial power-up: For
ページ9に含まれる内容の要旨
Bridged and Parallel Modes The S1500 / S2000 provides a rear-panel switch that allows it to be used in either a Bridged or Parallel mode. When this switch is placed in the “STEREO” PARALLEL BRIDGED STEREO (center) position, the S1500 / S2000 functions as a true stereo amplifier, where both of the two independent amplifier channels (Channel 1 and Channel 2) can receive different input signals and produce independent output signals. However, when the switch is placed in the “BRIDGED” (left) posit
ページ10に含まれる内容の要旨
S1500 / S2000 Connections + The illustrations on these two pages show the required interconnections when using the - S1500 / S2000 in Stereo, Bridged and Parallel modes. Wiring for Speakon™ connectors (shown on the right) is indicated where appropriate. Stereo Mode: (two or four speakers) SAMSON MMPL2242 SAMSON SAMSON MMPL2242 MMPL2242 MPL2242 MPL2242 MPL2242 MPL2242 MPL2242 MPL2242 Speakon™ wiring: Speakon™ wiring: USE SAME WIRING USE SAME WIRING FOR CH1, CH2 FOR CH1, CH2 1- 1+ 1- 1+ 2+ 2- 2+
ページ11に含まれる内容の要旨
S1500 / S2000 Connections Parallel Mode: (two or four speakers) SAMSON SAMSON MMPL2242 SAMSON MMPL2242 MMPL2242 MPL2242 MPL2242 MPL2242 MPL2242 MPL2242 MPL2242 Speakon™ wiring: Speakon™ wiring: USE SAME WIRING USE SAME WIRING FOR CH1, CH2 FOR CH1, CH2 1- 1+ 1- 1+ 2+ 2- 2+ 2- NOT CONNECTED NOT CONNECTED OUTPUT INPUT BRIDGED PUSH PUSH OUTPUT INPUT OUTPUT INPUT (8Ω ~16Ω ) BRIDGED PUSH PUSH BRIDGED PUSH PUSH (8Ω ~16Ω ) (8Ω ~16Ω ) (4Ω ~8Ω ) (4Ω ~8Ω ) BALANCED BALANCED (4Ω ~8Ω ) (4Ω ~8Ω ) (4Ω ~
ページ12に含まれる内容の要旨
Specifications 1. Rated Output Power, per channel (1 kHz, THD 0.1%, Both Ch Drive) Stereo / Parallel modes S1500, per channel (into 4 ohms) 760 W S1500, per channel (into 8 ohms) 520 W S2000, per channel (into 4 ohms) 1045 W S2000, per channel (into 8 ohms) 670 W Bridged mode S1500, per channel (into 8 ohms) 1520 W S2000, per channel (into 8 ohms) 2090 W 2. Frequency Response (0 dB, +0, -.5 dB) 10 Hz - 20 kHz 3. Total Harmonic Distortion (1/2 power @ 20 Hz - 20 kHz, Both Ch Drive into 4 oh
