ページ1に含まれる内容の要旨
TM
Digital Sound Projector
Owner’s Manual
English
for North America
ページ2に含まれる内容の要旨
The “ ” logo and “IntelliBeam” are trademarks of Yamaha Corporation. Manufactured under license from Cambridge Mechatronics Ltd. Worldwide patents applied for. ™ The “ ” logo and “Digital Sound Projector ” are trademarks of Cambridge Mechatronics Ltd. The “ ” logo and “Cinema DSP” are registered trademarks of Yamaha Corporation. “HDMI”, the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks or registered trademarks of HDMI Licensing LLC. The “ ” and “UniVolume” are tradem
ページ3に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX CONTENTS Useful features .............................................................. 31 INTRODUCTION Adjusting volume level automatically (UniVolume)....... 31 Features........................................................................... 4 Using the HDMI™ control function................................ 31 General operation flow .................................................. 5 Using the sleep timer ........................
ページ4に含まれる内容の要旨
INTRODUCTION Features Digital Sound Projector Wireless connection (yAired) ◆ Wireless connection with iPod/iPhone, using Yamaha wireless transmitter The Digital Sound Projector technology allows one slim unit to for iPod (PDX-50TX/PDX-50BC) control and steer multiple channels of sound to generate multi- ◆ Wireless connection with subwoofer, using Yamaha wireless subwoofer channel surround sound, thus eliminates the need for satellite kit (SWK-W10) (not available in some countries) loudspeake
ページ5に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX General operation flow 1 Install this unit and connect to other components. “Installation” (page 10), “Connections” (page 12) 2 Run AUTO SETUP to optimize the beam and sound settings. “AUTO SETUP (IntelliBeam)” (page 15) 3 Play back a source. “Playback” (page 21). 4 Change the playback method (surround/stereo), CINEMA DSP and/or beam modes settings. “Playback mode” (page 22). 5 Configure this unit's settings and/or set remote control c
ページ6に含まれる内容の要旨
Controls and functions Front panel 12 3 4 5 6 7 INPUT VOLUME INTELLIBEAM MIC 1 Remote control sensor 6 Power (p) key Receives infrared signals from the remote control (page 14). Turns on the power of this unit or sets it to the standby mode (page 21). 2 Power LED Lights up when the power is turned on (page 21). Note � In the standby mode, this unit consumes a small amount of power in order to 3 Front panel display receive infrared signals from the remote control or to search for HDMI Shows in
ページ7に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX Front panel display 12 3 4 5 6 789 TUNED STEREO SIRIUS TRNS RECV q DIGITAL PLUSq EX 96 HD MSTR HI RES Neo:6 AUTO MEMORY CATEGORY PCMq TRUE HDq PL x 24 ES DSCRT MTRX SLEEP VOL O L C R UNIVOLUME m SL SB SR ENHANCER ft EX1 LFE EX2 BASS EXT dB 0 A B C D 1 UNIVOLUME indicator 8 SLEEP indicator Lights up when the UniVolume function is turned on (page 31). Lights up when the sleep timer is set (page 31). 2 CINEMA DSP indicator 9 Volume leve
ページ8に含まれる内容の要旨
Rear panel C B OUT 1 HDMI IN 1 FRONT SURROUND SUR. BACK IR-OUT PRE OUT IN 2 IN 3 OUT 1 HDMI IN 1 IN 4 IN 2 A SUB IN 3 COMPONENT WOOFER SIRIUS SYSTEM CONNECTOR P R P B LL VIDEO Y VIDEO RR IN 4 IN OUT AUX 1 TV AUX 2 AUX 1 TV VIDEO AUDIO IN DIGITAL IN IR IN RS-232C L L L CENTER R R R SUB WOOFER IR-OUT AC IN FRONT SURROUND SUR. BACK PRE OUT 3 45 67 8 9 0 SUB FM ANTENNA WOOFER COMPONENT SIRIUS SYSTEM CONNECTOR IN OUT AUX 1 TV AUX 2 AUX 1 TV VIDEO AUDIO IN DIGITAL IN IR IN RS-232C 2 Note � The rear pa
ページ9に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX Remote control D Input selector keys A Use to select an input source (page 21). An input source key currently selected lights up when the remote control is operated. B E CINEMA DSP program keys Select the CINEMA DSP programs (page 22). TV AV C F SURROUND/STEREO TV AUX 1 AUX 2 Switches between surround and stereo playback (page 22). HDMI 1 HDMI 2 HDMI 3 D HDMI 4 iPod RADIO G Cursor ( / / / ) keys, ENTER ENTER MOVIE MUSIC TAINMENT OFF
ページ10に含まれる内容の要旨
PREPARATION Installation This section describes a suitable installation location to install this unit using a wall mount bracket, a rack, a table top stand or a floor stand. To achieve desired surround sound effects, install this unit where there are no objects such as furniture obstructing the path of sound beams (page 11). Depending on your installation environment, connections with external components (page 12) should be done before installation. ■ Using a wall mount bracket Notes You can u
ページ11に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX ■ Ideal installation condition : Object such as furniture Parallel installation (with 5Beam) Corner installation (with Stereo+3Beam) 40° to 50° ■ For better listening environment Example 1 Install this unit as close to the exact center of the wall as possible. Example 2 Install this unit so that the sound beams can be reflected off the walls. Example 3 Install this unit as close to the exact front of your normal listening position as p
ページ12に含まれる内容の要旨
Connections Component video pin cable Before connecting components ■ Cables used for connections The symbols on the left of cable names (such as , , and ) correspond with the symbols described in “Connecting your TV and Blu-ray disc player” (page 12) and “Connecting audio video components” (page 13). ■ Information on HDMI An HDMI cable can transmit both audio and video signals at the For audio and video same time. If your TV and other components have HDMI jacks, use HDMI cables for simpler
ページ13に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX ■ Connecting audio and video components Determine the connection types depending on the jacks available on this unit and your external components. The symbols in the following table correspond with the symbols described in “Cables used for connections” (page 12). HDMI IN 1 IN 2 IN 3 IN 4 IN OUT AUX 1 TV AUX 2 AUX 1 TV VIDEO AUDIO IN DIGIT T TAL IN IR IN RS-232C VIDEO AUDIO IN DIGITAL IN VIDEO IN/OUT AUDIO IN DIGITAL IN HDMI IN jacks
ページ14に含まれる内容の要旨
Connecting the FM antenna Connect the supplied FM antenna or your antenna to the FM ANTENNA jack on this unit. TV AV Antenna TV AUX 1 AUX 2 HDMI 1 HDMI 2 HDMI 3 HDMI 4 iPod RADIO ENTER MOVIE MUSIC TAINMENT OFF CINEMA DSP SURROUND STEREO FM ANTENNA ENTER ENTER G TOP MENU MENU OPTION OPTION SETUP SETUP RETURN RETURN I TV VOL CH VOLUME Preparing the remote control TV TV MUTE INPUT MUTE Note Operation range of the remote UNIVOLUME SUR. DECODE INTELLIBEAM � Before installing batteries or using the r
ページ15に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX p Changing OSD language You can select an OSD language among English, German, French, Spanish, Italian, Dutch and Russian. Before operating the following steps, select this unit as the video input on your TV. 1 Press and hold ISETUP until the 2 Press G / to select the desired “LANGUAGE SETUP” menu appears on your language and then press GENTER. Changing OSD TV. Choices: ENGLISH (English), DEUTSCH (German), language Français (Frenc
ページ16に含まれる内容の要旨
p “BEAM OPTIMZ ONLY” ■ Assembling the supplied cardboard microphone stand (Beam optimization only) Use to optimize the beam angle so that the parameter best matches your listening environment. 12 TV AV This menu takes about one minute. TV AUX 1 AUX 2 HDMI 1 HDMI 2 HDMI 3 Remove HDMI 4 iPod RADIO “SOUND OPTIMZ ONLY” ENTER MOVIE MUSIC TAINMENT OFF Fit in CINEMA DSP (Sound optimization only) SURROUND STEREO Use to optimize the beam delay, volume, and quality so that the parameters best match you
ページ17に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX p y 2 Press G / to select “AUTO SETUP” and � If “ENVIRONMENT CHECK [FAILED]” is displayed, then press GENTER. refer to “Error messages for AUTO SETUP” (page 18), press IRETURN, and then run the AUTO SETUP procedure again. B)AUTO SETUP � If “SUBWOOFER :NOT APPLICABLE” is displayed 1)BEAM+SOUND OPTIMZ even though a subwoofer is connected to this unit and 2)BEAM OPTIMZ ONLY turned on, check the connection and then increase the 3)S
ページ18に含まれる内容の要旨
■ Error messages for AUTO SETUP If an error message is displayed on your TV, check the error message list to solve the problem and then follow the procedure below. [ERROR E-1]: Press GENTER to run the AUTO SETUP procedure again or IRETURN to cancel the operation TV AV Other errors: Press IRETURN to cancel the operation and then run the AUTO SETUP procedure again. TV AUX 1 AUX 2 HDMI 1 HDMI 2 HDMI 3 Note HDMI 4 iPod RADIO ENTER MOVIE MUSIC TAINMENT OFF If the problem is difficult to be solved, c
ページ19に含まれる内容の要旨
INTRODUCTION PREPARATION PLAYBACK FEATURES SETTINGS APPENDIX p p p p p p Using the system memory You can save the current beam and sound settings in the system memory of this unit. It is handy to save certain settings according to the varying conditions of your listening environment. For example, if there are curtains in the path of sound beams, the effectiveness of the sound beams will vary depending on whether the curtains are open or closed. y � If there are curtains in your listening room,
ページ20に含まれる内容の要旨
4 Press G / to select the memory number to be loaded and then press GENTER. TV AV C TV TV A AUX 1 UX 1 A AUX 2 UX 2 HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3 1)MEMORY LOAD D HDMI 4 HDMI 4 iP iPod od RADIO RADIO ENTER MOVIE MUSIC TAINMENT OFF MEMORY1 Load Now ? CINEMA DSP SURROUND STEREO ENTER ENTER G Push [ENTER] to Load TOP MENU MENU OPTION SETUP RETURN TV VOL CH VOLUME 5 Press GENTER. The beam and sound settings saved in the selected K memory number are loaded. TV TV MUTE INPUT MUTE MUTE
