ページ1に含まれる内容の要旨
MICRO COMPONENT SYSTEM
UX-J60—Consists of CA-UXJ60 and SP-UXJ60
UX-J50—Consists of CA-UXJ50 and SP-UXJ50
RM-SUXJ60U REMOTE CONTROL
SP-UXJ60 CA-UXJ60 SP-UXJ60
RM-SUXJ50U REMOTE CONTROL
SP-UXJ50 CA-UXJ50 SP-UXJ50
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
ページ2に含まれる内容の要旨
Warnings, Cautions and Others CAUTION—STANDBY/ON button! Disconnect the mains plug to shut the power off completely (the STANDBY/ON lamp goes off). The STANDBY/ON button in any position does not disconnect the mains line. • When the unit is on standby, the STANDBY/ON lamp lights red. • When the unit is turned on, the STANDBY/ON lamp lights green. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do no
ページ3に含まれる内容の要旨
IMPORTANT FOR LASER PRODUCTS REPRODUCTION OF LABELS 1 CLASSIFICATION LABEL ON EXTERIOR SURFACE 2 WARNING LABEL INSIDE THE UNIT ADVARSEL: Usynlig laser- VARO: Avattaessa ja suo- CAUTION: Invisible laser VARNING: Osynlig laser- stråling ved åbning, når jalukitus ohitettaessa olet radiation when open and strålning när denna del är sikkerhedsafbrydere er ude alttiina näkymättömälle interlock failed or defeated. öppnad och spärren är AVOID DIRECT EXPOSURE af funktion. Undgå udsæt- urkopplad. Bet
ページ4に含まれる内容の要旨
Introduction We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. Power sources About This Manual • When unplugging the unit from the wall outlet, always pull This manual is organized as follows: on the plug, not the AC power cord. • The manual mainly explains operations using the buttons on the remote control. DO
ページ5に含まれる内容の要旨
Contents Location of the Buttons and Control ..................................... 3 Front Panel ........................................................................................... 3 Remote Control .................................................................................... 5 Getting Started ........................................................................ 6 Supplied Accessories ............................................................................ 6 Putting the Batt
ページ6に含まれる内容の要旨
Location of the Buttons and Control Become familiar with the buttons and control on your unit. Front Panel Front Panel 1 FOR UX-J50: w 2 e 3 4 r 5 FOR UX-J50: t 6 7 y 8 u i 9 MICRO COMPONENT SYSTEM UX-J60 p q 3 EN01-13_UX-J60&50[A]f.pm6 3 03.2.25, 5:08 PM
ページ7に含まれる内容の要旨
Continued Display Window 12 34 [ ] DAILY REC SLEEP REC SURROUND BASS ST MONO PRGM RANDOM ALL AHB 56 7 89p See the pages in parentheses for details. Front Panel Display Window 1 Disc tray 1 Timer indicators 2 Display window • (timer), DAILY, REC (recording timer), and SLEEP 3 REV.MODE (reverse mode) button (17 – 19) 2 REC (recording) indicator 4 AUX button (9) 3 ONLY FOR UX-J60: Pressing this button also turns on the unit. SURROUND indicator 4 ONLY FOR UX-J60: 5 STANDBY/ON button and STANDBY/ON
ページ8に含まれる内容の要旨
Remote Control See the pages in parentheses for details. 1 Number buttons 2 BASS button (10) 3 Multi operation buttons STANDBY/ON • UP, 4 (reverse skip), 7 (stop), ¢ (forward skip), and DOWN 1 2 3 8 4 SET button (15) DISPLAY 5 Source buttons 4 5 6 9 1 CLOCK • CD 3/8, TAPE 2 3, FM/AM, and AUX /TIMER Pressing one of these buttons also turns on the unit. 7 8 9 p 6 CD 0 (disc tray open/close) button (14) SLEEP 10 +10 q Pressing this button also turns on the unit. UP BASS TREBLE 7 REV.MODE (reverse m
ページ9に含まれる内容の要旨
Getting Started Continued Supplied Accessories Connecting Antennas Make sure that you have all the following items. FM antenna The number in parentheses indicates the quantity of each piece supplied. • AM loop antenna (1) FM antenna (supplied) • FM antenna (1) • Remote control (1) • Batteries (2) • Speaker cords (ONLY FOR UX-J60) (4) If anything is missing, consult your dealer immediately. Putting the Batteries into the Remote Control 1 Attach the FM antenna to the FM 75 Ω Insert the batteries—R
ページ10に含まれる内容の要旨
AM antenna Connecting Speakers 12 FOR UX-J60: 1 Vinyl-covered wire (not supplied) 23 3 Gray RIGHT RIGHT LEFT LEFT Red Speaker AM loop antenna cord Speaker MAIN SPEAKERS SUBWOOFERS (supplied) CAUTION: SPEAKER IMPEDANCE 6 -16 cord Black Blue 1 If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off. 2 Connect the AM loop antenna to the AM LOOP terminals as illustrated. INPUT INPUT INPUT INPUT 3 Turn the AM loop ante
ページ11に含まれる内容の要旨
1 If the cords are covered with insulation, Connecting Other Equipment remove a short section of insulation at the To connect an audio equipment end of each cord by twisting and pulling it You can connect audio equipment—used only as a playback off. device. 2 Press and hold the clamp of the speaker • DO NOT connect any equipment while the power terminal as illustrated. is on. • DO NOT plug in any equipment until all 3 Insert the end of the speaker cord into the connections are complete. terminal
ページ12に含まれる内容の要旨
Common Operations To change the clock Setting the Clock 1 Make sure the (timer) indicator is not lit on the Before operating the unit any further, first set the unit’s clock. display. When you plug the AC power cord into the wall outlet, • If it is lit, press and hold CLOCK/TIMER until it goes “0:00” starts flashing on the display. off. You can set the clock whether the unit is on or off. 2 Press CLOCK/TIMER repeatedly until the unit enters • There is a time limit in doing the following steps.
ページ13に含まれる内容の要旨
Continued Adjusting the Volume Enjoying Sound Effects You can adjust the volume level only while the unit is turned You can adjust the sound by using various sound effect on. The volume level can be adjusted between “VOL MIN” functions. and “VOLUME 1” – “VOLUME 40 (VOL MAX).” • These functions only affect the playback sound, and do not affect your recording. On the remote control: Press VOLUME + to increase the volume or To adjust the tone (Bass/Treble) press VOLUME – to decrease it. You can adj
ページ14に含まれる内容の要旨
To enjoy the heavy sound (ONLY FOR UX-J60) Selecting the Display Color (ONLY FOR UX-J60) You can enjoy the heavy sound. The function boosts low and You can select the display color (COLOR 1 – COLOR 5 and high frequency sounds—Sound Turbo. AUTO mode). SOUND Press SOUND TURBO. TURBO • AUTO mode changes the color (COLOR 1 to COLOR 5) • Each time you press the button, the Sound gradually. Turbo is turned on and off alternately. When it COLOR To select the color, press COLOR. is turned on, the BASS i
ページ15に含まれる内容の要旨
Listening to FM and AM Broadcasts Continued Tuning in to a Station Presetting Stations You can preset 30 FM and 15 AM stations. FM/AM In some cases, test frequencies have been already memorized 1 Press FM/AM to select the band. for the tuner since the factory examined the tuner preset The unit automatically turns on and tunes in function before shipment. This is not a malfunction. to the previously received station—either FM You need to preset stations separately for the FM and AM or AM. bands.
ページ16に含まれる内容の要旨
Tuning in to a Preset Station On the remote control ONLY: FM/AM 1 Press FM/AM to select the band. The unit automatically turns on and tunes in to the previously received station—either FM or AM. • Each time you press the button, the band alternates between FM and AM. UP 2 Press UP or DOWN to select a preset number. DOWN To tune in to a preset station directly using the number buttons On the remote control ONLY: Pressing the number button(s) allows you to select the preset number you want. Ex.: F
ページ17に含まれる内容の要旨
Playing Back Discs Continued This unit has been designed to play back the following discs Playing Back the Entire Disc—Normal Play —CD, CD-R, and CD-RW. CD When playing a CD-R or CD-RW 1 Press CD 0. User-edited CD-Rs (CD-Recordable) and CD-RWs The unit automatically turns on and the disc (CD-ReWritable) can be played only if they are already tray comes out. “finalized.” • Usually you can play back your original CD-Rs or CD- 2 Place a disc correctly on the circle of the RWs recorded in music CD f
ページ18に含まれる内容の要旨
PRGM Basic Disc Operations 2 Press PRGM (program). The PRGM (program) indicator lights up on While playing a disc, you can do the following operations. the display. To stop playing for a moment ST PRGM CD During play, press CD 3/8. While pausing, the elapsed playing time flashes on • If a program has been stored in memory, the program the display. is called up. To resume playing, press CD 3/8 again. UP 3 Press UP or DOWN to select the track number, then press SET. To go to another track • You ca
ページ19に含まれる内容の要旨
To modify the program Repeating Tracks—Repeat Play On the remote control ONLY: You can have all the tracks, the program or individual track CANCEL Before or after playing, you can erase the last currently playing, repeat as many times as you like. programed track by pressing CANCEL. • Each time you press the button, the last On the remote control ONLY: programed track is erased from the program. REPEAT To repeat playing, press REPEAT before or To add tracks in the program before playing, simply
ページ20に含まれる内容の要旨
Playing Back Tapes You can play back type I tapes. To stop playing, press 7. Playing Back a Tape To fast-wind to the left or to the right, press ¢ or 4 while the tape is not running. 1 Press PUSH OPEN 0 on the unit. The tape direction indicator (3 or 2) PUSH OPEN starts flashing rapidly on the display. To remove the cassette, press PUSH OPEN 0 on the unit. • If the tape is playing, stop it first. To play both sides—Reverse Mode You can set the deck to play just one side of a tape, both sides onc
