ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
( *
)
+
,
ページ3に含まれる内容の要旨
Your purchase of a new Gallien-Krueger 1001RB Series If your 1001RB Series amplifier or combo did not come product is surely the result of much careful consideration with all the items listed above, or if you encounter on your part. For our part, we at Gallien-Krueger are problems while setting up your new equipment, please pleased that you chose us, and are determined that you contact your local dealer, or us as soon as possible at: will be a satisfie
ページ4に含まれる内容の要旨
I have never seen the point in doing things the way others have done them. I also have not been very interested in following the latest fad. I am a Stanford educated engineer who worked his way through school as a musician. Like all musicians, I have lugged amplifiers up stairways and into car trunks, always wondering why these things had to be so heavy, bulky, and hard to handle. As I am the principal innovator at GK , our products reflect my attitudes and life
ページ5に含まれる内容の要旨
The 1001RB Series is designed to be simple to operate. All controls have a well defined purpose and are well behaved. These directions will take you through the basics and give you a good start for setting up your sound. . . Do not connect the Speakon cable labeled “Bridge Mode” Set the power switch to Off and connect the supplied to the 1001RB. This may result in damage to the ampli- power cable, from the amplifier AC receptacle, to an AC fier
ページ6に含まれる内容の要旨
The1001RB Series has several unique features which, if used properly, will obtain that sound you have been searching for. %
23 4. 6 . The Equalizer is used to fine tune your sound. When Turning up the Boost control, will add a little growl to adjusting it, do it just a little at a time. These are active your tone. This is an unmistakable GK trade mark circuits, and small changes can make a big difference in sound, that you will grow to appreciate. Ra
ページ7に含まれる内容の要旨
The 1001RB’s unique design makes setup for Bi-Amp or normal configuations simple. The operational mode is configured by how you connect your speaker cabinets. In addition, you have the option of driving one cabinet in Bi- Amp and one in Normal operation. "##"!
. "##"!
. "##"!
. "##"!
. The Bi-Amp feature of t
ページ8に含まれる内容の要旨
7
:
2/
. 8
0 9
85
5
To avoid safety hazards, use only the power cord supplied :. with your unit. If a replacement cord is used, make Your new 1001RB Series Bass Amp has been factory certain that it is of consistent quality and gauge as the configured for use with: original. We do not recommend using extension cords · 120 Volt/60Hz 20 Amp circuit for USA & Canada. with this product. As with all electrical dev
ページ9に含まれる内容の要旨
. 5. · To insure proper operation and to avoid When the unit gets dirty, wipe it with a clean, soft and potential safety hazards, place the unit on a dry cloth. If necessary, first wipe the surface with a firm, level surface. When installing the unit soft cloth slightly dampened with mild, soapy water, in a rack, be sure the mounting hardware can followed by a fresh cloth with clean water. Wipe support
ページ10に含まれる内容の要旨
12 13 14 15 16 17 18 6 7 8 9 10 11 1 2 3 4 5 19 !"
/0 !1 " An electronically balanced output, that you can run Boost and cut at 1 kHz +10dB, “Q Optimized,” band to your P.A. system. pass type. Works on lower string harmonics, and
effects the punch of your sound. Selects the direct out signal from before or after the EQ. 10-Low Mid:
Boost and cut at 250Hz +10dB, “Q Optimized,” Controls the level
ページ11に含まれる内容の要旨
"! 3 1 2 #"
$ % *) 6 The power cord is detachable and plugs in here. $ &'# #$
' 73 *% 8 ( $&(')*+,
"
&(' 540W power amp output for Full-Range operation only. )+,
"' ''& They deliver 540 watts into 4 Ohms. Lower impedances -'('# #' ''& should not be used. Each jack has a minimum of 8 Ohms ('
'"'
.'#/// each. Higher impedances such as 8 Ohms, 16 Ohms, or No Load ar
ページ12に含まれる内容の要旨
0++0# 1 The 1001RB Series combos deliver the1001RB’s unique features and distinct sound by using a variety of internal speaker configurations, GK’s RBH cabinet technology and a unique Lock N’ Roll transport system.
5 . 0
=
!
. 1001RB/115 One 8 Ohm 15″speaker and The Lock N’ Roll transport system is designed for quick one 8 Ohm horn and easy rolling of the combo on flat surfaces such as 1001RB/210 Two 16 Ohm 10″speakers carpet,
ページ13に含まれる内容の要旨
% 2 %
%
"##"!. There is nothing in the 1001RB Series power amp to come The1001RB Series is a flexible, state-of-the-art Bass between you and your sound except faithful, raw power. Amplifier, designed to deliver maximum performance, and be simple to operate. This is accomplished through a
. few, very important features: Bass players have always liked the growl they get from · Extremely high current power supply and slight overdrive
ページ14に含まれる内容の要旨
2 8 5
. 2
<. Bi-Amp systems allow the crossover to be electronic and Voicing filters are used to completely re-voice the therefore, have much higher quality than passive cross- amplifier. In the case of the Contour and String Bass controls, the effect is dramatic. overs. A crossover separates the sound into two parts (high and low frequency). The highs are sent to the horn The Contour control tunes between two different shaping or high frequen
ページ15に含まれる内容の要旨
% 2
! 5
A
! $ .
$% The 1001RB Series uses a “dual rail power supply” that To make use of the 1001RB’s Bi-Amp feature you will generates about half the heat of conventional amplifiers. need to use the four conductor Speakon cable (provided Low output signals run off a low voltage supply, and high with the 1001RB head, and included with the combos for level signals run off a high voltage supply. This keeps connection to the internal speak
ページ16に含まれる内容の要旨
& 0++0# % Output Power: Cooling Continuously Variable- 540W Amplifier 540W @ 8 Ohms Speed Fan 540W @ 4 Ohms Amplifier Protection: 50W Amplifier 50W @ 8 Ohms Full short circuit, thermal,& RF protection. 50W @ 4 Ohms Stable into reactive and mismatched loads. Input Section: Five second muted warm-up. Maximum Input Level 0.6V Rms Dimensions (HxWxD): With -10dB pad 1.6V Rms 3 1/2” x 17” x 8 ¼” Input Impedance 1M Ohm (2 Rack Spaces) Send output impedanc
