ページ1に含まれる内容の要旨
WideLine-10
Loudspeaker User Manual
WL2102 – Cored composite enclosure
WL2102-w – Birch plywood enclosure
AF2102-LA – Large aluminum array frame
WL SmALL Grid – Small steel array frame
TD-000227-00-C
*TD-000227-00*
ページ2に含まれる内容の要旨
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS Install in accordance with instructions by QSC Audio Products, LLC instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the install
ページ3に含まれる内容の要旨
Introduction The WideLine-10 loudspeaker system has been designed to provide a compact system that has unique dispersion characteristics, high-power handling and extended low-frequency response. Its primary uses include ballrooms, theatres, night clubs, houses of worship, and small to medium size events for the corporate and industrial markets. WL2102 enclosures are constructed of lightweight cored-composite and weigh 70 lb (31.8 kg). WL2102-w enclosures are constructed of birch plywood and
ページ4に含まれる内容の要旨
TRI AMP/BI AMP Switch TRI AMP TRI AMP: Shading network is NOT applied (shading must be provided by upstream signal processing). Connect the full-range input signal to pins 1+ and 1-, connect the shaded (processed) signal to pins 2+ and 2-. To flip shaded transducer location, use the mF (UNSHADED) SELECT switch or alter signal processing. Default mF (UNSHADED) SELECT switch position for three way mode is position A; if put in position B, connections (Table 1) to LF transducers A and B are i
ページ5に含まれる内容の要旨
Input Connections The input connectors are a pair of Neutrik NL8’s wired in parallel. Connections for bi-amp and tri-amp vary (Table 1). The pin designations for the NL8FC cable connector is shown for reference, bottom right. Note! In TRI AMP mode, the MF (UNSHADED) SELECT switch position determines the input connector wiring! Unexpected results may occur if switch positions and wiring are not strictly controlled. The WideLine-10 loudspeaker is not equipped with a crossover network. All si
ページ6に含まれる内容の要旨
Rigging Rules for Suspension • Correct use of all suspension hardware and components is imperative in sound system rigging and deployment. • Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits. • Research local codes and regulations to fully understand the requirements for suspended loads in the venue in which the equipment is to be suspended. • Use only shackle holes for suspension of array. • Be absolut
ページ7に含まれる内容の要旨
Rigging 1 WideLine-10 enclosures use a three-point suspension system. The system consists of front, left/right, captive articulated joints and a single rear link bar. Articulation is in 2° increments using the first location on the link bar. With the use of the second location, 1° degree increments can be obtained starting at 3°. The total available angular increments are: 0, 2, 3, 4, 5, 6, 7, 8, 9, and 10°. All pieces and locking pins remain with the 2 enclosures. No ancillary items are n
ページ8に含まれる内容の要旨
Adjusting the Angle Between Enclosures (Splay) The illustration shows the rear pin block of two enclosures joined by the upper enclosure’s rear link arm. Use the first pin location (closest to the end) on the link arm for setting in normalized 2° increments. The left-side example shows two enclosures linked for 8° of splay. The ball-lock pin is inserted into the 8° position in the rear block while passing through the “normal” pin hole in the link. When the “+3“ location is used, an addition
ページ9に含まれる内容の要旨
AF2102-LA The link arm is located on the bottom side of the frame assembly. Use this link for attaching the rear of the first enclosure. The frame allows for up or down angle options for use with either stacking or suspending. The 4° “normal” locations on the link system will yield a net 0° vertical inclination. Use 4° link location for 0° vertical inclination. WL SmALL Grid Do not stack more than four (4) enclosures on a WL SMALL GRID. Use only the QSC supplied 5/16" diameter x 1.25" long bal
ページ10に含まれる内容の要旨
Stacking the WL SmALL Grid The WL SmALL GRID comes with two aluminum I-bars used for aligning and securing the frame to QSC’s 215SB or 215PCm subwoofer. To use the I-bars, simply slide each one into the small frame’s L-track and secure with a stud fitting. Then, turn the frame over (I-bars on the bottom) and slide the exposed I-bars into the subwoofer’s L-track. Secure the I-bar with a stud fitting. Note that the stud fittings used are not required to be load rated as they only retain the I-ba
ページ11に含まれる内容の要旨
Specifications WL2102 WL2102-w Configuration Bi-amp or tri-amp mode Transducers Low-frequency 2 x 400 W, 16Ω 10" woofer, 3" voice coil, ceramic magnet assembly High-frequency 1.4" exit, 3" titanium diaphragm, neodymium magnet assembly 1 Frequency Response (±3 dB) 55 Hz – 18 kHz (with recommended DSP processing) Frequency Range (-10 dB) 48 Hz – 20 kHz (with recommended DSP processing) Nominal Impedance HF: 16Ω LF bi-amp mode: 8Ω LF tri-amp mode: 16Ω (x 2) Continuous Power Capacity / HF: 80 W /
ページ12に含まれる内容の要旨
Mailing Address: QSC Audio Products, LLC 1675 macArthur Boulevard Costa mesa, CA 92626-1468 USA Telephone Numbers: main Number: (714) 754-6175 Sales & marketing: (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service: (714) 957-7150 or toll free (USA only) (800) 772-2834 Facsimile Numbers: Sales & marketing FAX: (714) 754-6174 Customer Service FAX: (714) 754-6173 World Wide Web: www.qscaudio.com E-mail: info@qscaudio.com service@qscaudio.com © 2009 QSC Audio Products, LLC. All r
