ページ1に含まれる内容の要旨
Subwoofer MODEL
XTR102
XTR104
XTR122
XTR124
XTR152
XTR154
OWNER'S MANUAL
ページ2に含まれる内容の要旨
TABLE OF CONTENTS English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
WHAT’S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation. Listed below is a detailed list of the components included in this system package. Quantity Description 1 Owner's Manual 1 Orion XTR woofer 1 Mounting template 1 Trim ring TOOLS OF THE TRADE Listed are the majority of the tools required to perform the installation. Having the proper tools will make the installation much easier. It is very difficult when you get half way
ページ4に含まれる内容の要旨
FEATURES 12 3 15 4 14 13 5 12 6 11 7 Figure 1 Figura 1 10 9 8 Abbildung 1 1 Polypropylene dust cap - moisture and UV resistant. 2 Oversized NBR (Nitrile-butadiene Rubber) surround for linear controlled long excursion. 3 Paper cone - moisture and UV resistant. 4 Custom stamped steel frame. 5 Vented Aluminum voice coil former (2.5" voice coil former). 6 8mm steel front plate. 7 Large 2 stack ceramic magnets. (Large single magnet on 10" models) 8 8mm steel back plate/pole piece T yoke assembly. 9
ページ5に含まれる内容の要旨
WIRING CONFIGURATIONS Series - One Speaker (dual 2 ohm voice coils) One dual 2 ohm voice coil woofer with voice coils in connected in series results in a 4 ohm load to the amplifier. __ _ + Figure 2 Figura 2 Abbildung 2 ++ 1. Connect the woofer in series by connecting the negative (-) of one terminal to the positive (+) terminal of the other coil. 2. Wire the positive (+) terminal of the first coil to the positive (+) terminal on the amplifier. Wire the negative (-) terminal of the second coi
ページ6に含まれる内容の要旨
Parallel — One Speaker (dual 4 ohm voice coils) One dual 4 ohm voice coil woofer with voice coils in parallel results in a 2 ohm load to the amplifier. _ _ _ + Figure 4 Figura 4 ++ Abbildung 4 1. Connect the speaker in parallel by connecting the two positive (+) terminals together and the two negative (-) terminals together. 2. Wire both positive (+) terminals of the woofer to the positive (+) terminal on the amplifier. Wire both negative (-) terminals of the woofer to the negative (-) term
ページ7に含まれる内容の要旨
Parallel - Two Speaker (dual 4 ohm voice coils) Two dual 4 ohm voice coil woofers with voice coils in parallel and the two woofers in parallel results in a 1 ohm load to the amplifier. -- -- + + + + Figure 5 + Figura 5 Abbildung 5 - 1. Connect the speaker in parallel by connecting the four positive (+) terminals together and the four negative (-) terminals together. 2. Wire the positive (+) terminals of the woofers to the positive (+) terminal on the amplifier. Wire the negative (-) termina
ページ8に含まれる内容の要旨
Series/Parallel - Two Speakers (dual 2 ohm voice coils) Note: Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil. Two dual 2 ohm voice coil woofers with voice coils in series and then parallel the two series woofers results in a 2 ohm load to the amplifier. -- -- + + + + Figure 6 + Figura 6 Abbildung 6 - 1. Connect each woofer in series by connecting the negative
ページ9に含まれる内容の要旨
Series/Parallel - Three Speakers (dual 4 ohm voice coils) Note: Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil. Three dual 4 ohm voice coil woofer with voice coils of each woofer wired in series and then parallel the three woofers for a resulting 2.67 ohm load to the amplifier. -- -- -- + + + + + + Figure 7 + Figura 7 Abbildung 7 - 1. Connect each woofer in s
ページ10に含まれる内容の要旨
Series/Parallel - Three Speakers (dual 2 ohm voice coils) Note: Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil. Three dual 2 ohm voice coil woofer with voice coils of each woofer wired in series and then parallel the three woofers for a resulting 1.33 ohm load to the amplifier. -- -- -- + + + + + + Figure 8 + Figura 8 Abbildung 8 - 1. Connect each woofer in s
ページ11に含まれる内容の要旨
Series/Parallel - Four Speakers (dual 4 ohm voice coils) Note: Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil. Four dual 4 ohm voice coil woofers should be wired with the voice coils on each woofer in series and then parallel the four woofers for a resulting 2 ohm load to the amplifier. -- -- -- -- + + + + + + + + Figure 9 + Figura 9 Abbildung 9 - 1. Connect
ページ12に含まれる内容の要旨
Series/Parallel - Four Speakers (dual 2 ohm voice coils) Note: Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil. Four dual 2 ohm voice coil woofers should be wired with the voice coils on each woofer in series and then parallel the four woofers for a resulting 1 ohm load to the amplifier -- -- -- -- + + + + + + + + Figure 10 + Figura 10 Abbildung 10 - 1. Conne
ページ13に含まれる内容の要旨
2 Amplifiers - One Speaker (dual 2 ohm voice coils) One dual 2 ohm voice coil woofer with each voice coil connected to an individual amplifier, resulting in a 2 ohm load to each amplifier. -- ++ + - + Figure 11 Figura 11 Abbildung 11 - 1. Connect one of the speaker’s voice coils to the first amplifier by connecting the positive (+) terminal and the negative (-) terminal from the speaker to the respective positive (+) terminal and the negative (-) terminal from the first amplifier. 2. Connect
ページ14に含まれる内容の要旨
2 Amplifiers - One Speaker (dual 4 ohm voice coils) One dual 4 ohm voice coil woofer with each voice coil connected to an individual amplifier, resulting in a 4 ohm load to each amplifier. -- ++ + - + Figure 12 Figura 12 Abbildung 12 - 1. Connect one of the speaker’s voice coils to the first amplifier by connecting the positive (+) terminal and the negative (-) terminal from the speaker to the respective positive (+) terminal and the negative (-) terminal from the first amplifier. 2. Connect
ページ15に含まれる内容の要旨
SPECIFICATIONS Model/Part Number XTR102 XTR104 XTR122 Thiele/Small Parameters Fs (free-air resonance, Hz) 23.4 25.3 22.4 Vas (equivalent compliance, cu. ft.) 1.396 1.245 2.920 Vas (equivalent compliance, liters) 39.550 35.260 82.710 Qms (Q, mechanical) 5.95 5.52 7.28 Qes (Q, electrical) 0.55 0.58 0.51 Qts (total driver Q) 0.50 0.52 0.48 Re (DC resistance, ohms) 4.2 7.8 4.3 Z (nominal impedance, ohms) 4 8 4 Le (inductance, mh) 1.81 2.93 1.84 Efficiency (1W @ 1M, dB) 81.4 81.8 84.4 Xmax (one way l
ページ16に含まれる内容の要旨
SPECIFICATIONS Model/Part Number XTR124 XTR152 XTR154 Thiele/Small Parameters Fs (free-air resonance, Hz) 23.7 21.4 23.0 Vas (equivalent compliance, cu. ft.) 2.606 6.141 5.618 Vas (equivalent compliance, liters) 73.820 173.960 159.140 Qms (Q, mechanical) 6.15 6.93 6.53 Qes (Q, electrical) 0.53 0.61 0.73 Qts (total driver Q) 0.49 0.56 0.66 Re (DC resistance, ohms) 7.9 4.2 7.9 Z (nominal impedance, ohms) 8 4 4 Le (inductance, mh) 2.87 1.70 2.55 Efficiency (1W @ 1M, dB) 84.5 86.3 86.0 Xmax (one way
ページ17に含まれる内容の要旨
Enclosure Details 1. Parameters listed are for conventional applications only, for further help please call Audio Tech Support. 2. At least 0.75" MDF (Medium Density Fiberboard) is recommend for any XTR enclosure. 3. Recommended enclosures are NET box volumes, speaker and port displacement are calculated into the volume of the enclosure, you will not need to add these volumes to calculate GROSS volume for the enclosure. Notes * Due to the high power capabilities and long excursion of the X
ページ18に含まれる内容の要旨
Explanation of Enclosure Specifications There are many different factors that help determine the best style of enclosure for you or your vehicle. Listed below are some factors that should be considered. The size of the enclosure is directly proportional to the efficiency and power handling of that speaker. A woofer in a smaller enclosure will handle more power than the same woofer in a larger enclosure. The exact opposite is true for efficiency, a larger enclosure will play lower frequencie
ページ19に含まれる内容の要旨
ENCLOSURE RECOMMENDATIONS Enclosure Details 1. External dimensions calculated for 3/4” building material 2. Includes speaker displacement 3. Volumes given are net tuning volume 4. Enclosures include a minimal amount of damping material. Just enough material to line the inside of the enclosure is required. XTR102 & 104 Sealed Enclosure Recommendations Box Properties — Description — — Box Parameters — Type: Closed Box Vb = 1 cu.ft Shape: Prism, Square V(total) = 1.055 cu.ft Qtc = 0.692 QL = 7
ページ20に含まれる内容の要旨
XTR102 & 104 Vented Enclosure Recommendations Box Properties — Description — — Box Parameters — — Vents — Type: Vented Box Vb = 1 cu.ft No. of Vents = 1 Shape: Prism, Square V(total) = 1.111 cu.ft Vent shape = round Fb = 40 Hz Vent ends = one flush QL = 6.733 Dv = 3 in. (76 mm) F3 = 32 Hz Lv = 9.879 in. (251 mm) Fill = none Figure 15 External Dimensions Figura 15 A = 12 in. (305 mm) Abbildung 15 B = 15.5 in. (394 mm) C = 14.57 in. (370 mm) Internal Dimensions A = 10.5 in. (267 mm) A
