ページ1に含まれる内容の要旨
++
Preview
Sub-dial Button Quick-Release
Lid
Ikelite SLR-DC Housing Zoom
Strobe
Snap
Control
Mount
AEL/AFL
i n s t r u c t i o n m a n u a l
IKELITE
#6851.3 for Olympus E-3
Port Lock
Gear Sleeve
Lens
Drive Gear
Release
Rubber
Shutter
Handle
Release
Port
Opening
Lid Lid
Snap Snap
Strobe
Mount
Aluminum Tray
FRONT VIEW
Viewfinder Port
M
O P Q
Shutter
AEL/
L
Release
AFL
Zoom
Quick
Release Main Dial
Button
F G
N
N N
H
Congratulations on your purchase of an Ikelite Digital Camera I
Power Switch
J
Hous
ページ2に含まれる内容の要旨
F Fl la as sh h C Co on nn ne ec ct ti io on n f fo or r E Ex xt te er rn na al l S St tr ro ob be es s C Cl lo os si in ng g t th he e H Ho ou us si in ng g When using an external strobe, slide the housing hotshoe 1. Place housing face down in your lap. connector into the hotshoe camera mount 2. Check to see that there is an o’ring Slide the connector on the housing back and that it is forward until it External Strobe Connector clean and in its proper location. Waterproof Cap stops. This can 3
ページ3に含まれる内容の要旨
I In ns st ta al ll li in ng g t th he e Z Zo oo om m C Cl la am mp p & & G Ge ea ar r S Sl le ee ev ve e O On n t th he e T Ty yp pe e 1 1 L Le en ns se es s I In ns st ta al ll l t th he e G Ge ea ar r S Sl le ee ev ve e After the Zoom Clamp is installed, lower the appropriate Gear I In ns st ta al ll li in ng g t th he e Z Zo oo om m C Cl la am mp p Sleeve over the Zoom Clamp aligning the Gear Sleeve ribs with the The Zoom Clamp has springs so it can be expanded to fit over grooves in the Zoo
ページ4に含まれる内容の要旨
I In ns st ta al ll li in ng g t th he e P Po or rt t Port Lock I In ns st ta al ll li in ng g t th he e P Po or rt t c co on nt t. . Release Button There are two port locks on P Po or rt t S Se ea al l I In ns si id de e V Vi ie ew w the front of the housing. If the port is installed before the camera is inserted into the (See housing front) Each housing, look on the inside of the port lock has a Release Locked Position housings at the port seal. Check Button, lift the release Lift Release to s
ページ5に含まれる内容の要旨
D DS S2 20 00 0 S Su ub bs st tr ro ob be es s S St tr ro ob be e A Ar rm ms s • DS200 SubStrobes with a Serial Number 6,499 or below require This housing offers two types of arm mounting systems. The an update to operate with the TTL Conversion Circuitry. top of the rubber handles utilize Ikelite’s Quick-Release Arm, available with the SA-100R Arm system. • DS200 Substrobes with a Serial Number of 6,500 or higher or with one of the two following labels in the battery compartment The bottom
ページ6に含まれる内容の要旨
C Ch ho oo os si in ng g a a P Po or rt t P Po or rt ts s C Co on nt ti in nu ue ed d F FL LA AT T P PO OR RT T • With the lens on the camera extended to full length, measure from front of For standard, macro, and telephoto lenses. camera to face of lens. Due to refraction flat ports reduce the angle-of -coverage of a lens • Select the appropriate port based on the and at the same time enlarge the image. This makes the flat port lens type and length. ideal when using standard, macro or zoom lens
ページ7に含まれる内容の要旨
3. Some of the controls have a short shaft and cannot be pulled G Ge en ne er ra al l T Ti ip ps s out exposing the shaft for lubrication. In the unlikely event one 1. You should completely assemble and test your set-up in a of these controls sticks or becomes difficult to operate you can swimming pool before using it in open water. remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, 2. It is a good idea to start each pho
