ページ1に含まれる内容の要旨
Ceiling Subwoofer
Model CSUB
Installation and Use Manual
© 2008 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-2171-01B0810
ページ2に含まれる内容の要旨
Product Description Thank you for choosing Bogen’s CSUB Ceiling Subwoofer. Please familiarize yourself with the product by reading and reviewing the descriptions and diagrams in this manual. Bogen’s CSUB delivers unsurpassed performance and value. This subwoofer can be installed either in suspended ceiling structures or hard surfaces (such as drywall). It is ready to install with swinging arm clamps that take the place of a tile bridge for installa- tion in suspended ceilings. A variety of speak
ページ3に含まれる内容の要旨
Product Diagrams 2 1 Front Drawing (grille removed) 1. Driver Assembly (internal) 3 2. Bass Tuning Vent 3. Grille Retention Groove 4 4. 24" Ceiling Tile Guide Arrows (×2) 5. Power Tap Selection Switch 7 6. 14-1/2" Joist Space Guide 5 6 Arrows (×2) Front Drawing 7. Mounting Clamp Screws (×4) (grille removed) Side Drawing 8 8. Metal Back Can 9. Snap-Lock Input Connector 9 10. Terminal Cover (side view) 11 11. Mounting Clamps (×4) 10 Side Drawing Rear Drawing 12 12. Safety Tether Point 13. Snap-Loc
ページ4に含まれる内容の要旨
Speaker Placement The low frequency capability of the CSUB allows great flexibility in its placement. While full-range speakers will typically be installed throughout the ceiling in an evenly spread pattern, the CSUB can be placed wherever it is most convenient. This usually means where the subwoofers best meet the needs of the overall sound system, or may some- times mean where they best fit into the ceiling. This flexibility is useful in irregularly- shaped rooms or when the depth of the area
ページ5に含まれる内容の要旨
Installation The unique clamp-mounting system of the Bogen CSUB not only allows mounting in most types of ceiling surface thicknesses, it takes the ease of installation two significant steps further: 1. NO TILE BRIDGE IS REQUIRED. Because the mounting clamps are extra-long and very durable, they can suspend and support the CSUB across the 24" span of a suspended ceiling. This eliminates the need for the separate tile bridge required for nearly all ceiling speakers. 2. A uniquely designed cl
ページ6に含まれる内容の要旨
Installation (cont.) SUSPENDED CEILINGS: 1. Remove the ceiling tile from the ceiling grid. Cut a 14-1/4" circular hole in the ceil- ing tile. Use the included template as a guide. 2. Put the CSUB face down on a workbench or on the floor without grille installed. 3. Place the ceiling tile over the CSUB, making 2×2 Ceiling Tile sure the ceiling tile is facing out. It is impor- Mounting clamps (×4) tant to note the direction of the clamps: they must be installed so that they span the distance from
ページ7に含まれる内容の要旨
Installation (cont.) DRYWALL OR OTHER HARD SURFACES: 1 Be sure you know the location of the ceiling joists before cutting the speaker open- ing. Cut a 14-1/4" circular hole where the CSUB will be installed. Use the includ- ed template as a guide. 2. Make electrical connections to the snap-lock input connector and then plug it into the CSUB (see Speaker Wiring section). 3. Install terminal cover using the supplied screws. If using conduit, refer to the Terminal Cover section of this manual. Mount
ページ8に含まれる内容の要旨
Speaker Wiring All wiring should be done prior to installation and then plugged into the rear of the speaker. Wiring is terminated at a snap-lock input connector. There are two positive and two negative terminals to accommodate daisy-chaining of speakers in a sys- tem. Daisy-Chaining The snap-lock input connector allows for easy daisy-chaining of speakers by providing a second terminal of each polarity. See the figures to the right and below for correct wiring for daisy-chain- ing of terminals.
ページ9に含まれる内容の要旨
Selecting Power Levels The front-mounted selector switch is used to set the appropriate power level or impedance for your system. Using your fingers or a flat-blade screwdriver, turn the knob until the arrow points to the power level you require. 70V Systems A power setting scale for 70V systems is labeled on the switch. Six settings are available, from 2 to 64 watts. 8-ohm Systems The fully counterclockwise position of the setting switch is the 8-ohm position. This set- ting is suitable for use
ページ10に含まれる内容の要旨
Specifications SPECIFICATIONS CSUB * 40 Hz to 125 Hz Frequency Response (-6 dB) * 91 dBspl Sensitivity (1W/1M) Dispersion Omni-directional Power Input (Max.) 150W @ 8 ohms; 64W @ 70V † 70V: 64, 32, 16, 8, 4, 2 Power Settings (in watts) Fire-rated (94V0) ABS Baffle Material Back Can Material Heavy-gauge Steel Terminations 4-Terminal Snap-Lock Input Connector Included Accessories (1) Snap-Lock Input Connector, (1) Steel Terminal Cover with (2) mounting screws, and (1) Package, Butyl Tape Optional
ページ11に含まれる内容の要旨
Limited Warranty; Exclusion of Certain Damages The Bogen Ceiling Subwoofer, model CSUB, is warranted to be free from defects in material or workmanship for three (3) years from the date of sale to the original purchas- er. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey,
ページ12に含まれる内容の要旨
50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com
